Installation Instructions

ManualsBrandsAltronix ManualsPower Supply UnitsVERTILINE16DI

CCTV Isolated Rack Mount

Power Supplies

Installation Guide

Models Include:

Vertiline8i Vertiline8Di

- 24VAC or 28VAC @ 8 amp - 24VAC or 28VAC @ 8 amp

- Eight (8) fuse protected electronically - Eight (8) PTC protected electronically

isolated outputs isolated outputs

Vertiline16i Vertiline16Di

- 24VAC or 28VAC @ 16 amp - 24VAC or 28VAC @ 16 amp

- Sixteen (16) fuse protected electronically - Sixteen (16) PTC protected electronically

isolated outputs isolated outputs

Rev. 031808

More than just power.

Summary of content (8 pages)

PAGE 1
CCTV Isolated Rack Mount Power Supplies Installation Guide Models Include: Vertiline8i Vertiline8Di Vertiline16i Vertiline16Di - 24VAC or 28VAC @ 8 amp - 24VAC or 28VAC @ 8 amp - Eight (8) fuse protected electronically - Eight (8) PTC protected electronically isolated outputs isolated outputs - 24VAC or 28VAC @ 16 amp - 24VAC or 28VAC @ 16 amp - Sixteen (16) fuse protected electronically - Sixteen (16) PTC protected electronically isolated outputs isolated outputs Rev.
PAGE 2
Overview: Altronix Vertiline AC Isolated CCTV Rack Mount Power Supplies provide 8 or 16 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. The units feature individually selectable 24VAC and/or 28VAC power outputs. Specifications: Features: Input: • Selectable 115VAC 60 Hz or 230VAC 50/60 Hz input. Output: • Eight (8) or sixteen (16) individually selectable 24VAC or 28VAC power outputs with OFF position. • Maximum 1 amp per output.
PAGE 3
8. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 3, pg. 6). 9. Connect the power outputs of the terminals marked [1P & 1N] to the power inputs of camera 1 (Fig. 2, pg. 5). Repeat this step for each additional camera (Outputs 2-16). After wiring is completed, insert terminal block into the corresponding connector and secure by tightening the screws. 10. Upon completion of wiring, set illuminated master power disconnect circuit breaker to the ON (RESET) position (Fig.
PAGE 4
-4- Vertiline8i/Vertiline16i P N 15 P N 14 P N 16 P N 15 P N 14 P N 13 13 P P N N 12 12 P N P N 11 11 P N P N 10 10 P N P N 1 9 9 P P 3 4 28VAC OFF 24VAC 5 6 8 N 8 P N 7 P N 6 P N 5 P N 8 P N 7 P N 6 P N 5 P 1d - Power Outputs: 24VAC or 28VAC. 7 1b - Output voltage switches: Selects 24VAC or 28VAC or OFF for each output. PTC protected models (Vertiline8Di and Vertiline16Di) do not have output fuses on the rear of rack mount chassis.
PAGE 5
Vertiline8i/Vertiline16i -5- OFF RESET Fig.
PAGE 6
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
PAGE 7
Mounting Options: Rack Mount Installation 1- Remove factory installed screws from both sides of rack chassis (Fig. 4a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the two (2) flat head screws (B) (included) (Fig. 4b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 4c). Fig. 4 Fig. 4b Fig. 4a Top Fig.
PAGE 8
Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A.