User's Manual
Table Of Contents
- Revision History
- 1. Installation and General Information
- 1.1 Introduction
- 1.2 Installing iOS App from Apple App Store
- 1.3 Installing Android App
- 1.4 Installing the Sentinare Sensor
- 1.5 Disclaimers, Limitations and Known Issues
- 1.6 Troubleshooting
- 1.7 Technical Support
- 1.8 Certificates
- 1.9. Federal Communications Commission (FCC) Interference Statement
- 1.10 Innovation, Science and Economic Development Canada (ISED) Interference Statement
- 2. User Account Management
- 3.Room Management
- 4.Device Management
- 4.1 Add a Device
- 4.2 Device Streaming and Setting
- 4.2.1 Rename Device
- 4.2.2 Refresh Display
- 4.2.3 Voice Call
- 4.2.4 Setup WiFi
- 4.2.5 Calibration
- 4.2.6 Region of Interest (ROI)
- 4.2.7 View Recordings
- 4.2.8 Updating Firmware
- 4.2.9 Restart
- 4.2.10 Change Room
- 4.2.11 Remove Device
- 4.2.12 Privacy Mode
- 4.2.13 Upside-Down Installation
- 4.2.14 Delay Fall Alert
- 4.2.15 Hand Waving Detection and Sensitivity
- 4.2.16 Advanced Settings
- 4.2.17 Factory Reset
- 4.2.18 Configuring Night Vision
- 4.2.19 LED Green Light
- 4.2.20 Alert Sound
- 4.2.21 Stick Figure Recording
- 4.2.22 HDMI Output (Cypress Only)
- 4.2.23 Local Video Recording (Cypress Only)
- 4.2.24 Meanings of LED Colors
- 5.People Management
- 6.Alerts
- 7.Fall Risk Assessment
- 7.1 Introduction
- 8.Dashboard
- 9. Account Settings
- 10. Sentinare Web Hub
- 11. API for Third-Party Integration
38
User account in the China server:
https://app.altumview.com.cn
Restrict Region
If a ROI is defined as a Restrict Region, when the face of a person in the specified person groups is
recognized in the region, an alert will be sent to the cloud and the app. If the person’s face is not
recognized in the restricted region but is recognized after the face leaves the region, but is still in the
same sensor’s view, the sensor can still send the alert.
After a restricted region alert is generated, no duplicated alert will be generated in 60 seconds.
One possible application of the Restricted Region is to monitor people with dementia. For example,
users can first define a Person Group called “Dementia”, then assign people with dementia to this
Person Group in their profile pages, and finally define a restricted region from the ROI page for the
Dementia person group. After that, any person in the Dementia group entering the restricted region will
trigger an alert.
4.2.7 View Recordings
Sentinare protects people’s privacy by only transmitting stick figures out of the sensor. It can also record
the continuous stick figure activities in the server for future playback and analyses whenever a person
appears in the field of view of a sensor. This feature can be used to analyze a person’s health,
investigate an incident, and improve the quality of service of an organization.
Free access to three days of stick figure is provided by default. Monthly fee is required if you need to
access to longer periods of stick figure recordings.
To access the recorded stick figures from a sensor, go to the main page of the sensor, and tap the “View
Recordings” command. In the next page, as shown by the following figure, users can use the calendar to
select a day within the subscription plan. The activity bar below the calendar will indicate the times that
stick figure recordings are available for the selected day. Users can move the cursor in the activity bar to
select a specific time, and the corresponding records will be downloaded from the server for playback in
the window below the bar.
Each segment of the stick figure recording is up to two minutes. To load the previous or the next
segment, users can tap the left arrow or the right arrow at the two ends of the activity bar.