INSTALLATION INSTRUCTIONS Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxshowerdoor.com 300d SERIES FRAMELESS SHOWER DOOR Copyright © Alumax Bath Enclosures 2000. All rights reserved.
LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers, customers, and all subsequent purchasers and users, that the products supplied by it shall be free from material defects in material and workmanship for a period of one (1) year after shipment, provided they are installed and maintained according to Alumax Bath Enclosures' recommended practices and installation instructions.
00d PARTS LIST A. B. C. D. E. F. G. H. I. J. 1 Shower Curb 1 Glazed Door Panel Assembly 2 Wall Jamb 6 Plastic Wall Anchors 6 #8 x 1 1/2" Truss Head Screws 6 #6 x 3/8" Pan Head Tek Screws 1 Strike Jamb w/Magnet 1 Hinge Jamb 1 Latch Vinyl 1 Latch K. L. M. N. O. P. Q. R.
1 The Alumax 300D Continous Hinge Shower Door is completely reversible and may be installed hinge-left or hinge-right. Refer to the illustration to determine the correct position for your installation. For maximum waterproofing, the hinge jamb should always be opposite the shower head. These instructions depict a hinge-left installation. CAUTION: For safety, the door must always open outward. 2 NOTE: The 300D unit may be installed without using the sloped curb [A] provided.
4 Lay the door glass [B] on a flat work surface and position the hinges [Q] by sliding them until they are lined up with the holes in the door glass. Remove the hinge plate and bushing. Position the door on the hinges and insert the plastic hinge bushing into the hole. Place the hinge plate on the glass,insert the hinge plate attachment screw and only tighten the screw enough to secure the hinge plate temporarily.
7 Cut one wall jamb [C] to the same length as the strike jamb [G]. Place the wall jamb [C] just cut against the strike side wall with the bottom end 3/16" from the raised side of the curb [A]. Plumb the jamb and mark the hole locations on the wall. Repeat for the other wall jamb. Remove all parts and drill the walls for mounting hardware. For tile or marble walls, drill six 3/16" diameter holes and insert the plastic wall anchors [D]. Attachments to fiberglass or acrylic units can be made in two ways.
10 Slide the strike jamb [G] over the remaining mounted wall jambs [C] with the magnet facing outward. The distance from the edge of the door panel glass to the face of the strike jamb should be 1/4". Plumb the strike jamb vertically and mark the location on the wall jamb. EXTERIOR 11 Inside the shower enclosure, drill two 1/8" holes thru the strike jamb [G] and into the wall jamb [C] 3/8" to 3/4" from the wall and approximately 1" vertically from each end of the strike jamb.
13 Locate the handle [K] that has no Set Screws. Place a Plastic Bushing [M] in the top handle hole then place a Plastic Washer [L] against the glass. Place the handle without Set Screws against the Plastic Washer and insert the threaded end of the Cone Head Screw [N] through the bushing into the threaded insert in the end of the handle and tighten. Repeat the procedure for the bottom hole.
To keep your Alumax Bath Enclosure looking like new we recommend the Alumax ShowerBright Consumer Maintenance Kit. The Consumer Maintenance Kit surface should be applied every 45 to 60 days. To purchase or for more information contact your dealer. Our dealers have the materials to do a professional ShowerBright restoration. For best results professional restorations should be performed a maximum of once every three months. Contact your dealer for more information.