Owner's manual

ManualsBrandsAlumax ManualsFor HomeABC Series

Model

ABC32 - ABC36 - ABC42

INSTALLATION MANUAL

Acrylic Shower Base

06.10 K

Summary of content (12 pages)

PAGE 1
Model Acrylic Shower Base ABC32 - ABC36 - ABC42 INSTALLATION MANUAL 06.
PAGE 2
ABC32 - ABC36 - ABC42 ● Table of Contents IMPORTANT .................................................... CARE FOR YOUR ACRYLIC SHOWER BASE .................. SPECIFICATION. ............................................... TOOLS AND MATERIALS REQUIRED. ........................ 1. PREPARE DRAINING PIPE. ................................. 2. INSTALL THE DRAIN. ...................................... 3. LEVELING THE BASE. ..................................... 4. TESTING THE DRAINAGE...............................
PAGE 3
ABC32 - ABC36 - ABC42 SPECIFICATION. Dimensions* Model A B C D E ABC32 32” [81.3cm] 32” [81.3cm] 5 1/2” [14cm] 12” [30.5cm] 12” [30.5cm] ABC36 36” [91.4cm] 36” [91.4cm] 5 1/2” [14cm] 12” [30.5cm] 12” [30.5cm] ABC42 42” 42” [106.7cm] [106.7cm] 5 1/2” [14cm] 12” [30.5cm] 12” [30.5cm] * Tolerance on dimensions: ±1/4” [.6 cm] TOOLS AND MATERIALS REQUIRED. DRILL LEVEL 06.
PAGE 4
1 1A. ABC32 - ABC36 - ABC42 PREPARE DRAINING PIPE. modate plumbing. The 2” (5.0cm) drain pipe should Note: Dimensions D and E are 12” ±¼” from wall to center of drain. 12” [30.5 cm] 12” [30.5 cm] 1B. Position base. Verify that the draining pipe location matches the actual location of the base drain. Remove the base. 2 INSTALL THE DRAIN. Drain not included 2A. Prior to install the drain on the base, run a bead of silicone between the drain body and shower base.
PAGE 5
3 ABC32 - ABC36 - ABC42 NIVELEZ LA BASE. 3A. Level the base by adjusting the legs underneath. Check your adjustment with a level. 3A 3B. Tighten the hexagon nut to block the legs height. 4 4A. 3B TESTING THE DRAINAGE. the base with a small amount of water. 4A 4B. Check for any leakage around the drain (some bubbles may appear) and below (if you have access to). 4C. Unplug the drain and assure that the drainage is efThere must be no puddle of water accumulation in the base. 06.
PAGE 6
5 ABC32 - ABC36 - ABC42 FASTEN THE BASE. Shim if necessary 5A. Locate and drill with a 3/16” drill bit, the screw 5B 5B. Fasten base to studs using #8 x 1 1/4” screws (preferably stainless steel screws) 5A 66 FINISHING. Stud. Drywall. Tile adhesive. Tips to achieve a professional looking and Tile. Tiling 3 to 4mm gap. Silicone. Shower base. Shim if necessary. 06.
PAGE 7
Model ABC36 ST Acrylic Shower Base INSTALLATION MANUAL 06.
PAGE 8
ABC36 ST ● Table of Contents IMPORTANT .................................................... CARE FOR YOUR ACRYLIC SHOWER BASE .................. SPECIFICATION. ............................................... TOOLS AND MATERIALS REQUIRED. ........................ 1. PREPARE DRAINING PIPE. ................................. 2. INSTALL THE DRAIN. ...................................... 3. LEVELING THE BASE. ..................................... 4. TESTING THE DRAINAGE.................................. 5.
PAGE 9
ABC36 ST SPECIFICATION. * Tolerance on dimensions: ±1/4” [.6 cm] TOOLS AND MATERIALS REQUIRED. DRILL LEVEL 06.
PAGE 10
1 1A. ABC36 ST PREPARE DRAINING PIPE. modate plumbing. The 2” (5.0cm) drain pipe should Note: Dimensions D and E are 18” (46cm)±¼” from wall to center of drain. dimensions. Dim E Dim D 18” [46cm] 18” [46cm] 1B. Position base. Verify that the draining pipe location matches the actual location of the base drain. Remove the base. 2 INSTALL THE DRAIN. Drain not included 2A. Prior to install the drain on the base, run a bead of silicone between the drain body and shower base.
PAGE 11
3 ABC36 ST LEVELING THE BASE. 3A. Level the base by adjusting the legs underneath. Check your adjustment with a level. 3A 3B. Tighten the hexagon nut to block the legs height. 4 4A. 3B TESTING THE DRAINAGE. the base with a small amount of water. 4A 4B. Check for any leakage around the drain (some bubbles may appear) and below (if you have access to). 4C. Unplug the drain and assure that the drainage is efThere must be no puddle of water accumulation in the base. 06.
PAGE 12
5 ABC36 ST FASTEN THE BASE. 5A. Locate and drill with a 3/16” drill bit, the screw Shim if necessary 5B 5B. Fasten base to studs using #8 x 1 1/4” screws (preferably stainless steel screws) 5A 66 FINISHING. Stud. Drywall. Tile adhesive. Tips to achieve a professional looking and Tile. Tiling 3 to 4mm gap. Silicone. Shower base. Shim if necessary. 06.