K-KR4Z - Kona 07.
CURVED GLASS SLIDING SHOWER DOOR Please keep this manual and product code number for future reference and replacement parts ordering if necessary.
CURVED GLASS SLIDING SHOWER DOOR INSTALLATION INSTRUCTIONS FOR CURVED GLASS SLIDING SHOWER DOOR Congratulations! You have made the right choice in buying this shower system. We are convinced that you will be entirely satisfied with our product.
PACKAGING CHECK LIST & HARDWARE 11 9 1 2 8 3 4 5 6 7 10 1 WALL JAMB (2) 2 3 4 SET OF HANDLES (2) 8 SIDE GASKET WALL JAMB SIDE (2) EXPANDER (2) 5 SIDE GASKET (4) 9 TOP TRACK (1) FIXED PANEL (2) 6 DOOR PANEL ASSEMBLY (2) 10 MAGNETIC DOOR GASKET (2) 7 BOTTOM TRACK (1) 11 GLASS SUPPORT (8) PAGE 1
PACKAGING CHECK LIST & HARDWARE 5 4 8 10 OR FOR ‘’PARIS POINT ’’ GLASS ONLY SET OF HANDLES (2) 11 GLASS SUPPORT (8) 15 SCREW CAP (8) SIDE GASKET (4) 12 SIDE GASKET (2) 14 13 WALL PLUG (8) BOTTOM SLIDER SHIM (4) SCREW 1 3/8” LG (12) (M4 X 35) SCREW 3/8” LG (8) (M4 X 8) 18 17 16 MAGNETIC DOOR GASKET (2) SCREW 15/32” LG (4) EXPANDER CAP (2) (M4 X 12) PAGE 2
REQUIRED TOOLS LIST 1/4” 1/8” DRILL BIT CERAMIC TILE DRILL BIT 5/16 HEX NUT DRIVER SCREWDRIVERS DRILL HACKSAW HAMMER * * Required for one piece shower unit installation.
DOOR INSTALLATION STEPS NOTICE For one piece shower unit installation. Prior to installation, to fit the corner contour of your shower unit, it's recommended to round of the edge of wall jamb and/or expander with a hacksaw as shown. INTERIOR SHOWER SIDE TOP VIEW WALLJAMB (2) Round-off edge OR 0 LEVEL EXPANDER & WALLJAMB (2) Round-off edge shower unit NOTICE: If necessary, round-off a little more.
DOOR INSTALLATION STEPS Step 1 EXPENDER (2) + TRACK (2) + SCREW 1 3/8’’ LG (4) TOP TRACK (1) Step 2 INSERT WALL JAMBS TEMPORALLY BOTTOM TRACK (1) PAGE 5
DOOR INSTALLATION STEPS Step 3 POSITION AND CENTER THE FRAME TOGETHER WITH WALLJAMBS ONTO THRESHOLD OF SHOWER BASE. Step 4 - ADJUST AND LEVEL THE FRAME ASSEMBLY. - TRACE OUTER EDGE OF WALL JAMBS. - REMOVE FRAME ASSEMBLY FROM BASE.
DOOR INSTALLATION STEPS 5A Step - REALIGN WALL JAMB WITH REFERENCE LINE (2). - MARK DRILLING LOCATION FOLLOWING PILOT HOLES. - DRILL HOLES BY USING SUITABLE 1/4” DRILL BIT. 5 5B 6B 6A Step 6 - INSERT THE WALL PLUGS (8) AND PUT IN EACH A DROP OF SILICONE.
DOOR INSTALLATION STEPS Step TOP TRACK 7 INSTALL THE FIXED PANELS (2) BY SECURING THEM WITH THE GLASS SUPPORTS (8) & SCREW 15/32” LG (4).
DOOR INSTALLATION STEPS Step 8 INSERT ONE SIDE OF FRAME INTO WALL JAMB Sl e id 9B Pu sh INTERIOR SHOWER SIDE Slide e id Sl 9A Push Pu sh Step 9 ENGAGE THE OTHER SIDE OF FRAME INTO WALL JAMB PAGE 9
DOOR INSTALLATION STEPS Step 10 PRIOR TO INSTALL DOOR PANELS INSERT MAGNETIC DOOR GASKET (2) (OPTIONAL) PUSH DOWN 11C INTERIOR SHOWER SIDE PUSH DOWN 11A INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE Step 11 11B INSERT DOOR PANELS INTO TOP & BOTTOM TRACK PAGE 10
DOOR INSTALLATION STEPS Step 12 USE HEX NUT DRIVER OR PLIERS FOR VERTICAL DOOR ADJUSTMENT TIGHTEN LOOSEN 12A 12E 12D 12B 12C VERTICAL ADJUSTMENT Step INTERIOR SHOWER SIDE INSERT SIDE GASKET WALL JAMB SIDE (2) (both sides) 14 OR (FOR ‘’PARIS POINT ’’ GLASS ONLY) INTERIOR SHOWER SIDE TOP VIEW Step 13 INSTALL SIDE PANEL GASKET ONTO FIXED PANELS & DOOR PANELS (4) PAGE 11
DOOR INSTALLATION STEPS Step - LEVEL AND ADJUST FRAME - FASTEN FRAME WITH SCREW 3/8” LG (8) + SCREW CAP (8) 15 INTERIOR SHOWER SIDE B 1/8” A DRILL BIT INTERIOR SHOWER SIDE B INTERIOR SHOWER SIDE A PAGE 12
DOOR INSTALLATION STEPS Step 16 INSERT EXPANDER CAPS (2) 24 Hours Step 17 SILICONE EXTERIOR ON BOTH SIDES, ALONG THE WALL JAMBS AND WALLS. ALSO ALONG THE BOTTOM TRACK AND THE SIDE PANELS.
