K-KS914Z - Kona INSTRUCTION MANUAL FRAMELESS SLIDING SHOWER ENCLOSURE 07.
Please keep this manual and product code number for future reference and replacement parts ordering if necessary.
READ CAREFULLY AND COMPLETELY BEFORE PROCEEDING IT IS RECOMMENDED THAT YOU WEAR SAFETY GLASSES AT ALL TIMES DURING INSTALLATION INSTALLATION OVER CERAMIC TILE If your shower door is to be installed over ceramic tile, tile should extend completely under both wall jambs. Silicone should be used to seal the line where ceramic tile meets the base. HOW TO CARE FOR YOUR DOOR Never use scouring powder pads or sharp instruments on metal work or glass panels.
8 TOP TRACK WITH ROUNDED CHANNEL 9 6 5 4 11 3 2 10 1 7 BOTTOM TRACK WITH FLAT CHANNEL 1 2 3 WALL JAMB (2) 4 EXPANDER (2) 5 FIXED PANEL (2) 6 7 SET OF HANDLES (2) SIDE GASKET (4) DOOR PANEL ASSEMBLY (2) BOTTOM TRACK (1) 8 9 10 11 SIDE GASKET WALL JAMB SIDE (2) TOP TRACK (1) MAGNETIC DOOR GASKET (2) GLASS SUPPORT (8) PAGE 1
REQUIRED TOOLS LIST 1/4” 1/8” DRILL BIT CERAMIC TILE DRILL BIT SCREWDRIVERS 5/16 SILICON DRILL LEVEL HEX NUT DRIVER PENCIL MEASURE TAPE MALLET PACKAGING CHECK LIST & HARDWARE 5 4 8 OR 10 (FOR ‘’PARIS POINT ’’ GLASS ONLY) SET OF HANDLES (2) SIDE GASKET (4) 12 11 SIDE GASKET (2) 13 MAGNETIC DOOR GASKET (2) 14 (M4 X 8) BOTTOM SLIDER SHIM (4) GLASS SUPPORT (8) 16 15 SCREW 1 3/8” LG (14) SCREW 3/8” LG (8) 18 17 (M4 X 35) SCREW CAP (8) WALL PLUG (8) (M4 X 8) SCREW 15/32” LG
INSTRUCTION MANUAL TOP TRACK WITH ROUNDED CHANNEL BOTTOM TRACK WITH FLAT CHANNEL Step 1 Step 2 EXPENDER (2) + TRACK (2) + SCREW 1 3/8’’ LG (8) INSERT WALL JAMBS PAGE 3
INSTRUCTION MANUAL Step 3 Step 4 POSITION AND CENTER THE FRAME TOGETHER WITH WALLJAMBS ONTO THRESHOLD OF SHOWER BASE. - ADJUST AND LEVEL THE FRAME ASSEMBLY. - MARK DRILLING LOCATION FOLLOWING PILOT HOLES. - REMOVE FRAME ASSEMBLY FROM BASE.
INSTRUCTION MANUAL 5A 5B Step 5 - INSERT THE WALL PLUGS (8) AND PUT IN EACH A DROP OF SILICONE.
INSTRUCTION MANUAL Step TOP TRACK 7 INSTALL THE FIXED PANELS (2) BY SECURING THEM WITH THE GLASS SUPPORTS (8) & SCREW 15/32” LG (4).
INSTRUCTION MANUAL Step 8 PRIOR TO INSTALL DOOR PANELS INSERT MAGNETIC DOOR GASKET (2) (OPTIONAL) PUSH DOWN 9C PUSH DOWN 9A INTERIOR SHOWER SIDE 9B INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE Step 9 INSERT DOOR PANELS INTO TOP & BOTTOM TRACK PAGE 7
INSTRUCTION MANUAL Step 10 USE HEX NUT DRIVER OR PLIERS FOR VERTICAL DOOR ADJUSTMENT TIGHTEN LOOSEN 10A 10E 10D 10B 10C VERTICAL ADJUSTMENT Step INTERIOR SHOWER SIDE INSERT SIDE GASKET WALL JAMB SIDE (2) (both sides) 12 OR (FOR ‘’PARIS POINT ’’ GLASS ONLY) INTERIOR SHOWER SIDE TOP VIEW Step 11 INSTALL SIDE PANEL GASKET ONTO FIXED PANELS & DOOR PANELS (4) PAGE 8
INSTRUCTION MANUAL Step 13 - LEVEL AND ADJUST FRAME - FASTEN FRAME WITH SCREW 3/8” LG (8) + SCREW CAP (8) INTERIOR SHOWER SIDE B A INTERIOR SHOWER SIDE B INTERIOR SHOWER SIDE A PAGE 9
INSTRUCTION MANUAL Step 14 INSERT EXPANDER CAPS 24 Hours Step 15 SILICONE EXTERIOR ON BOTH SIDES, ALONG THE WALL JAMBS AND WALLS. ALSO ALONG THE BOTTOM TRACK AND THE SIDE PANELS.
