Walk-in ● Shower System L-201X-25, L-202X-25 L-311TBX-25, L-312TBX-25 L-311X-34, L-312X-34 L-311X-25, L-312X-25 L-201X-34, L-202X-34 L-311TBX-34, L-312TBX-34 L001 08.
Please keep this manual and product code number for future reference and replacement parts ordering if necessary.
2 PEOPLE REQUIRED GENERAL INSTRUCTIONS • Read this manual carefully and completely before proceeding. • It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES • Silicone should be used to seal the gap where the ceramic tiles meet the panel. • If your shower door is to be installed over ceramic tiles, the tiles should lay completely under the wall • jamb. NOTICE • Caulking: no sealant is required inside the shower. Unless otherwise stated.
INSTALLATION MANUAL 201X-25, 202X-25 PARTS LISTING HARDWARE 11.1 WALL PLUG #6-1 11.2 HINGE SCREW #8-3/8 1 11.3 SCREW #8-1 1/4 11.4 SCREW CAP 11.5 SPACING BLOCK HINGE ITEM # PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 1 4 HINGE 2 5 BOTTOM GLASS CLIP 2 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 11 HARDWARE 11.1 WALL PLUG #6-1 4 11.2 SELF DRIILLING SCREW #8-3/8 3 11.3 SELF DRILLING SCREW #8-1 1/4 3 11.
INSTALLATION MANUAL 201X-25, 202X-25 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE SILICONE 1/4˝& 1/8˝ DRILL BITS LEVEL MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Return panel • Bottom clips • Side gasket • Door bottom see page 20 see page 16-17 5
INSTALLATION MANUAL 311X-25, 312X-25 PARTS LISTING 6 HARDWARE 4 8 11.1 9.2 CHEVILLE #6-1 WALL PLUG #6-1 HINGE 11.2 VIS # 8-3/8 SCREW #8-3/8 9.3 11.3 VIS # 8-1 1/4 SCREW #8-1 1/4 9.1 11.4 CAPUCHON COUVRE-VIS SCREW CAP 11.5 HINGE BLOC ESPACEUR SPACING BLOCK 5 4 7 ITEM NO. PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 2 4 HINGE 2 5 BOTTOM GLASS CLIP 4 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 9.
INSTALLATION MANUAL 311X-25, 312X-25 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE SILICONE 1/4˝& 1/8˝ DRILL BITS LEVEL MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Return panel • Bottom clips • Side gasket • Door bottom see page 20 see page 16-17 7
GUIDE D’INSTALLATION INSTALLATION MANUAL 311TBX-25, 312TBX-25 PARTS LISTING 6 HARDWARE 4 8 11.1 9.2 WALL PLUG #6-1 9.3 HINGE 11.2 SCREW #8-3/8 10 11.3 SCREW #8-1 1/4 9.1 11.4 SCREW CAP 11.5 HINGE SPACING BLOCK 5 4 7 5 ITEM NO. PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 2 4 HINGE 2 5 BOTTOM GLASS CLIP 4 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 9.1 RETURN PANEL 1 9.2 EXPANDER 1 9.
INSTALLATION MANUAL 311TBX-25, 312TBX-25 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE SILICONE 1/4˝& 1/8˝ DRILL BITS LEVEL MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Towel Bar see page 22 • Return panel • Bottom clips • Side gasket • Door bottom see page 16-17 see page 20 9
INSTALLATION MANUAL 201X-34, 202X-34 PARTS LISTING HARDWARE 11.1 HINGE WALL PLUG #6-1 1 11.2 SCREW #8-3/8 11.3 SCREW #8-1 1/4 11.4 SCREW CAP 11.5 HINGE SPACING BLOCK ITEM NO. PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 1 4 HINGE 2 5 BOTTOM GLASS CLIP 2 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 11 HARDWARE 11.1 WALL PLUG #6-1 4 11.2 SELF DRIILLING SCREW #8-3/8 3 11.3 SELF DRILLING SCREW #8-1 1/4 3 11.
INSTALLATION MANUAL 201X-34, 202X-34 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE 1/4˝& 1/8˝ DRILL BITS LEVEL SILICONE MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Return panel • Bottom clips • Side gasket • Door bottom see page 16-17 see page 20 11
INSTALLATION MANUAL 311X-34, 312X-34 PARTS LISTING HARDWARE 9.2 11.1 WALL PLUG #6-1 HINGE 11.2 SCREW #8-3/8 9.3 11.3 SCREW #8-1 1/4 11.4 SCREW CAP HINGE 11.5 SPACING BLOCK ITEM NO. PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 2 2 4 HINGE 5 BOTTOM GLASS CLIP 4 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 9.1 RETURN PANEL 1 9.2 EXPANDER 1 9.3 GASKET 1 11 HARDWARE 11.1 WALL PLUG #6-1 8 11.
INSTALLATION MANUAL 311X-34, 312X-34 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE SILICONE 1/4˝& 1/8˝ DRILL BITS LEVEL MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Return panel • Bottom clips • Side gasket • Door bottom see page 16-17 see page 20 13
INSTALLATION MANUAL 311TBX-34, 312TBX-34 PARTS LISTING HARDWARE 9.2 11.1 WALL PLUG #6-1 HINGE 9.3 11.2 SCREW #8-3/8 11.3 SCREW #8-1 1/4 11.4 SCREW CAP 11.5 HINGE SPACING BLOCK ITEM NO. PARTS QTY 1 DOOR PANEL 1 2.1 FIXED PANEL 1 2.2 EXPANDER 1 2.3 GASKET 1 3 WALL JAMB 2 4 HINGE 2 5 BOTTOM GLASS CLIP 4 6 SUPPORT BAR 1 7 BOTTOM DOOR GASKET 1 8 SIDE GASKET 1 9.1 RETURN PANEL 1 9.2 EXPANDER 1 9.3 GASKET 1 10 TOWEL BAR 1 11 HARDWARE 11.
INSTALLATION MANUAL 311TBX-34, 312TBX-34 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE SILICONE 1/4˝& 1/8˝ DRILL BITS LEVEL MALLET BLOCK INSTALLATION OF COMPONENTS • Support Bar see page 18-19 • Hinges • Door panel see page 21 • Panneau de retour • Supports inférieurs • Return panel • Bottom clips • Towel Bar see page 22 • Side gasket • Door bottom voir page 16-17 see page 16-17 see page 20 15
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 1 FIXED PANEL INSTALLATION THIS INSTALLATION PROCEDURE APPLIES FOR ALL RETURN PANELS INSTALLATION REGARDLESS OF QUANTITY OR ADDITIONAL FIXTURE SUCH AS TOWEL BAR. 3 1a 1a. Using a measuring tape, mark the center of the threshold of the base. 1b. Using the marking established in the previous step, run a second line up the wall. Use a level to ensure verticality of this line. 1b 1c.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 1 CONTINUED 1e. 1e. Place the bottom clips (5) for return panel on the line traced previously following dimension shown on the plan view. Mark the screw location. Remove temporary the bottom clips to drill the base using #1/8” drill bit. Put silicone onto the bottom clip bottom face groove and around the hole. Finally, fasten the bottom clips to the base using the provided screws. Place the gaskets into bottom clips slots.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 2 SUPPORT BAR INSTALLATION 2a 2a. Take apart the end component (A) of the support bar with the provided Allen Key. 6 B WALL END COMPONENT A 2b 2b. Transfer the position of the bottom clip (8) to the back wall. At 82” from the threshold mark the position (center of the cylinder ) for the support bar end component (A) mounting MIN 82” | M AX. 8 2 1/4” 2d. Drill the back wall using a Ø1/4”drill bit. 2e.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 2 CONTINUED 2h 2h. Insert the clear gasket as shown. Then Loosen and rotate support bar to grab the front panel. B Clear Gasket 5 2g. Level support bar. Tighten the set screws. 2g A B B.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 3 GASKETS INSTALLATION 3a panel side gasket to the glass 3a. Align the panel edge. Insert it with a 2˝ x 6˝ x 1/2˝ block and a mallet. Trim the excess using the cutting plier. INTERIOR SHOWER SIDE 8 2.1 3b. Cut the bottom door gasket (7) as illustrated. The lip should be about 3/4˝ longer than the rest. 8 2.1 3c. Rest the door panel (1) on a fat surface. With the mallet, insert the bottom door gasket (7) at the bottom of the door.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 4 HINGES INSTALLATION 4a 4a. Fasten one side of the hinges (4) onto the panel (2.1). Do not tighten all the way for this step to allow other door (1) adjustments. INTERIOR SHOWER SIDE 4 1 4b. Place the door panel vertically next to the panel (2.1). The holes for the hinges should be aligned. 4b 4c. Fasten the hinge on the door (1).The door panel must be leveled before tightening the hinges completely. 4d. Remove the spacing blocks (11.5).
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 5 TOWEL BAR INSTALLATION 5a 9.1 5a.For 4302 - 4303 - 56302 -56303 - 4302 4303 - 56302 - 56303. If installation of return panel (9.1) has not been performed yet please, refer to step #1 to complete the installation. 5b.Install the towel bar (10) as illustrated.
INSTALLATION MANUAL 201X, 202X, 311X, 312X, 311TBX, 312TBX 6 SILICONE SEAL THE SHOWER DOOR 6a. Seal the exterior of the shower along the wall with silicone. Fill gap between the glass panels and base surrounding the bottom clips (5).
