Walk-in • Shower System L-203X-34 L-313X-34 L-313TBX-34 L007 08/10
Please keep this manual and product code number for future reference and replacement parts ordering if necessary.
2 PEOPLE REQUIRED GENERAL INSTRUCTIONS - Read this manual carefully and completely before proceeding. - It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES - Silicone should be used to seal the gap where the ceramic - If your shower door is to be installed over ceramic tiles, the tiles should lay completely under the wall jamb. NOTICE - Caulking: no sealant is required inside the shower . Unless otherwise stated.
INSTRUCTION MANUAL 203X-34 PARTS LISTING 2.3 2.2 HARDWARE 5 10.1 WALL PLUG #6-1 1 10.2 SCREW 3/8" LG 2.1 3 10.3 SCREW 1 1/4" LG a 10.4 b SCREW CAP 6 4 7 IT E M # P AR TS QTY 1 W AL L JAM B 1 2 .1 F IX E D F R O N T P A N E L 1 2 .2 G AS K E T 1 2 .3 E XP AN D E R 1 3 S M AL L R E T U R N P AN E L 1 4 C O R N E R C L IP 2 5 S U P P O R T B AR 1 6 B O T T O M G L A S S C L IP 2 7 L O N G B O T T O M C L IP 1 10 H AR D W AR E 1 0 .
INSTRUCTION MANUAL 203X-34 TOOLS AND MATERIALS REQUIRED DRILL 1/4” CERAMIC TILE DRILL BIT LEVEL HAMMER SCREWDRIVERS MEASURE 1/8” ACRYLIC DRILL BIT SILICONE ALLEN KEY PENCIL INSTRUCTION SHEETS CONTENTS Support bar see page 9-10 small fixed panel corner clips long bottom clip front panel bottom clips see page 7-8 see page 1 1-12 2
INSTRUCTION MANUAL 313X-34 PARTS LISTING 2.2 2.3 HARDWARE 8.2 5 10.1 8.3 3 WALL PLUG #6-1 1 10.2 1 2.1 SCREW 3/8" LG 10.3 8.1 SCREW 1 1/4" LG a 10.4 b SCREW CAP 6 4 IT E M # 1 2 .1 2 .2 7 6 P A R T S Q T Y W AL L JAM B 2 F IX E D F R O N T P A N E L G AS K E T 1 1 2 .3 E XP AN D E R 1 3 S M AL L R E TU R N P AN E L 1 4 C O R N E R C L IP 2 5 S U P P O R T B AR 1 6 B O T T O M G L A S S C L IP 4 7 L O N G B O T T O M C L IP 1 8 .1 R E TU R N P AN E L 1 8 .
INSTRUCTION MANUAL 313X-34 TOOLS AND MATERIALS REQUIRED DRILL HAMMER SCREWDRIVERS 1/4” LEVEL MEASURE TAPE 1/8” 1/4” CERAMIC TILE DRILL BIT ACRYLIC DRILL BIT SILICONE ALLEN KEY PENCIL INSTRUCTION SHEETS CONTENTS Support bar see page 9-10 return panel bottom clips see page 7-8 small fixed panel corner clips long bottom clip front panel bottom clips see page 7-8 see page 1 1-12 4
INSTRUCTION MANUAL 313TBX-34 PARTS LISTING 2.2 2.3 HARDWARE 8.2 5 8.3 10.1 3 WALL PLUG #6-1 1 1 10.2 9 2.1 SCREW 3/8" LG 10.3 8.1 SCREW 1 1/4" LG a 10.4 b SCREW CAP 6 4 IT E M # 1 2 .2 2 .2 6 7 P A R T S Q TY W AL L JAM B 2 F IX E D F R O N T P A N E L G AS K E T 1 1 2 .3 E XP AN D E R 1 3 S M AL L R E TU R N P AN E L 1 4 C O R N E R C L IP 2 5 S U P P O R T B AR 1 6 B O T T O M G L A S S C L IP 4 7 L O N G B O T T O M C L IP 1 8 .1 R E TU R N P AN E L 1 8 .
INSTRUCTION MANUAL 313TBX-34 TOOLS AND MATERIALS REQUIRED DRILL HAMMER SCREWDRIVERS 1/4” LEVEL MEASURE TAPE 1/8” 1/4” CERAMIC TILE DRILL BIT ACRYLIC DRILL BIT SILICONE ALLEN KEY PENCIL INSTRUCTION SHEETS CONTENTS Support bar voir page 9-10 see page 9-10 return panel bottom clips see page 7-8 towel bar see page 13 small fixed panel corner clips long bottom clip front panel bottom clips see page 7-8 see page 1 1-12 6
INSTRUCTION MANUAL 203X, 313X, 313TBX 1 FRONT PANEL INSTALLATION RETURN PANEL INSTALLATION THIS INSTALLATION PROCEDURE APPLIES FOR ALL RETURN PANELS INSTALLATION REGARDLESS QUANTITY OR ADITTIONAL FIXTURE AS TOWEL BAR. 1a. Using a measuring tape, mark the center of the threshold of the base. 1 1a 1b. Using the marking established in the previous step, run a second line up the wall. Use a level to ensure verticality of this line. 1b 1c.
INSTRUCTION MANUAL 203X, 313X, 313TBX 1 CONTINUED 1e. Place the bottom clips (6) for return panel on the line traced previously following dimension shown on the plan view. Mark the screw location. 1e Remove temporary the bottom clips to drill the base using #1/8” drill bit. Put silicone onto the bottom clip bottom face groove and around the hole. Finally , fasten the bottom clips to the base using the provided screws.Place the gaskets into bottom clips slots. 1f.
INSTRUCTION MANUAL 203X, 313X, 313TBX SUPPORT BARS INSTALLATION 2a. Take apart the end component of the support bar with the provided Allen Key. 2a 5.1 WALL END COMPONENT 5.2 2b. Transfer the position of the bottom clips (6) to the back wall. At 82” from the threshold mark the position (center of the cylinder 5.2) for the support bar end component mounting. 2b 2c MIN 82” | MAX . 82 1/4” 2c. Drill the back wall using a 1/4”drill bit. 2d 2d. Apply silicone in the holes and insert the wall plugs.
INSTRUCTION MANUAL 203X, 313X, 313TBX 2 CONTINUED 2f 2f. Place the front fixed panel into the bottom clips (6) attached to the base. Loosen the support bar as necessary to allow the bar to rotate and hold the glass from the top. Put the gaskets as shown in the detail and proceed to rotate the bar until it meets the glass panel. 5.3 6 2g. Level support bar by loosening wall end component set screw (5.2) and glass holder set screw (5.3) adjusting to the proper position. Fasten securely all screws.
INSTRUCTION MANUAL 203X, 313X, 313TBX 3 BOTTOM CLIPS INSTALLATION CORNER CLIPS INSTALLATION 3a. Proceed to install the corner clips (4) onto the glass panels (2) (3)temporary. Located in front of the unit place the small fixed panel inner face(3) onto the edge of the front fixed panel (1) as shown in the detail. Holding the glass from the front install corner clip front plate onto front panel slots. Slide the corner clip until it meets the front panel holes.
INSTRUCTION MANUAL 203X, 313X, 313TBX 3 CONTINUED 3c. Remove the small fixed panel (3) by unscrewing the corner clip back plate. On the marked positions drill the base with a drill bit 1/8”. Put silicone onto the bottom clip bottom face groove and around the hole. Fasten it to the base with screw #6-1”. Install the provided gasket. 3c 3 2 3d. Insert small fixed panel back into bottom clips slots and fasten the back corner clip plate temporary until proper leveling of panels is completed.
INSTRUCTION MANUAL 313X, 313TBX 4 TOWEL BAR INSTALLATION 4a. For L-313X and L-313TBX models. If installation of return panel has not been performed yet please, refer to step #1to complete the installation. 4a model L-313TBX model L-313X 8.1 9 4b. For L-313TBX model install the towel bar as illustrated.
INSTRUCTION MANUAL 203X, 313X, 313TBX 5 SILICONE SEAL THE SHOWER DOOR 5a. Silicone seal the exterior of the shower along the wall. Fill gap between glass panels and base surrounding the bottom clips (6). 5a 5b 5b. Placed inside the shower silicone seal de corner between the glass panels all the way long trough out the corner clips (4).
