M-90X INSTRUCTION MANUAL M006
Please keep this manual and product code number for future reference and to order replacement parts if necessary.
INSTRUCTION MANUAL ● Table of Contents MODEL NUMBER............................................... 2 GENERAL INSTRUCTIONS .................................... 3 INSTALLATION OVER CERAMIC TILES ....................... 3 NOTICE ......................................................... 3 CARE FOR YOUR FRAMELESS SHOWER DOOR ............. 3 PARTS LISTING................................................. 4 PROVIDED HARDWARE........................................ 6 TOOLS AND MATERIALS REQUIRED ...................
INSTRUCTION MANUAL PARTS LISTING 4 5 1 6 2 7 3 8 9 10 ITEM QTY PARTS 1 WALL JAMB (TEMPLATE) 1 2 MAGNETIC EXPANDER 1 3 MAGNETIC DOOR GASKET 1 4 DOOR PANEL 1 5 OVAL WALL MOUNT HINGE 2 6 SIDE PANEL GASKET 1 7 HANDLE CURVED 1 8 BOTTOM DOOR GASKET 1 9 SPACING BLOCKS 2 10 THRESHOLD 1 *next page 4
INSTRUCTION MANUAL MODEL DOOR PANEL BOTTOM DOOR GASKET THRESHOLD 23 (20 3/16” x 75”) 21 1/2” 24 1/4” 24 (21 3/16” x 75”) 22 1/2” 25 1/4” 25 (22 3/16” x 75”) 23 1/2” 26 1/4” 26 (23 3/16” x 75”) 24 1/2” 27 1/4” 27 (24 3/16” x 75”) 25 1/2” 28 1/4” 28 (25 3/16” x 75”) 26 1/2” 29 1/4” 29 (26 3/16” x 75”) 27 1/2” 30 1/4” 30 (27 3/16” x 75”) 28 1/2” 31 1/4” 31 (28 3/16” x 75”) 29 1/2” 32 1/4” 32 (29 3/16” x 75”) 30 1/2” 33 1/4” 33 (30 3/16” x 75”) 31 1/2” 34 1/4” 34
INSTRUCTION MANUAL PROVIDED HARDWARE 11 12 13 14 ITEM HARDWARE QTY 11 WALL PLUG 3 12 SCREW CAP 4 13 SELF DRILLING SCREW #8-3/8 14 3 SELF-DRILLING SCREW #8-1 1/4 3 TOOLS AND MATERIALS REQUIRED * SCREWDRIVERS DRILL SILICONE 1/4˝& 1/8˝ DRILL BITS If the shower panels are to be assembled on ceramic tiles, use a 1/4˝ drill bit for ceramic tiles.
INSTRUCTION MANUAL 1 DETERMINE HINGES LOCATION. WALL-MOUNTED HINGES MUST BE SUPPORTED AND FASTENED INTO A STUD FRAMING. USE THE WALL JAMB (#1) AS TEMPLATE TO MARK DRILLING LOCATIONS FOR WALL-MOUNTED HINGES. 1A. Determine on which side the hinges will be mounted. 1B 1B. Trace a centerline on the threshold and run it up along the wall. 1C. Place the wall jamb (#1) on the threshold by centering the slotted holes with the centerline. 1D.
INSTRUCTION MANUAL 2 FASTEN THE HINGES TO THE WALL. NEVER PLACE THE GLASS DIRECTLY ON THE FLOOR. 2A. Fasten the hinges (#5) to the wall as illustrated. 2A INTERIOR SHOWER SIDE 3 PREASSEMBLE THE DOOR. INTERIOR SHOWER SIDE 3 3A. 8 Temporarily insert the bottom door gasket (#8) under the door panel. LIP 7 6 9 4 4 FINAL RESULT 3B. Install the 2 spacing blocks (#9) onto the bottom lip of the gasket. INTERIOR SHOWER SIDE 3C.
INSTRUCTION MANUAL 4 INSTALL THE DOOR PANEL. IT IS BEST TO HAVE 2 PEOPLE WORKING ON THIS STEP. 4 INTERIOR SHOWER SIDE 4A. Place the door assembly on the shower threshold and level it. 4B 4B. Fasten the hinges as illustrated using the Allen key. 4A 4C. Remove the spacing blocks (#9) and the bottom door gasket. 9 4C 5 INSTALL THE DOOR HANDLE. 5A. Install the curved door handle (#7) as illustrated.
INSTRUCTION MANUAL 6 MOUNT THE WALL JAMB. NOTE CHOOSE 1 OF THE 2 HOLES AT THE TOP AND BOTTOM OF THE WALL JAMB. 1 6A 11 14 6B 6C 6D 6A. Place the wall jamb (#1) on the center of the threshold and align it using a level. Trace the outer edge of the wall jamb and the holes onto the wall. Remove the wall jamb. 6B. With a 1/4˝ drill bit, drill 3 holes into the wall using the marks as a guide. 6C. 6C(a) 6C(b) TOP VIEW TOP VIEW WALL STUD the drilled hole location, skip this step.
INSTRUCTION MANUAL 7 INSERT THE MAGNETIC EXPANDER 7A. Insert magnetic expander (#2) into the wall jamb (#1) 7A 1 2 7B. Adjust and level the door panel. The magnetic gaskets must be alligned and in contact. 7C. Combine the 3 3/8˝ screws (#13) with the inner screw caps (#12b). Fasten the magnetic expander. 7D. Snap the screw caps (#12a) on the screws.
INSTRUCTION MANUAL 8 INSTALL THE DOOR GASKETS. 4 3 8A 8 8B 45º INTERIOR SHOWER SIDE 8 6 8A. Align the bottom door gasket (#8) to the wall and project on it the 45° magnetic gasket (#3) surface. RIGID PART ± 1/8" 8B. Using the cutting plier, trim the bottom door gasket at ± 5/8" 8C ± 1/2" SUGGESTED TRIMMING 8C. Open the door and clean the door panel surface on which the door side gasket (#6) will be placed. Align gasket. Make sure it is oriented as illustrated. 8D 8D.
INSTRUCTION MANUAL 9 SILICONE SEAL THE SHOWER. HOURS 9A 4 INTERIOR SHOWER SIDE 8 10 9A. Silicone seal the exterior of the shower along the wall and the wall jamb (#1). 9B 9B. Position the threshold (#10) under the door panel as illustrated. Lift it to pass a bead of silicone underneath. Apply silicone on the outside edges. WE RECOMMEND TO HOLD THE THRESHOLD (#10) IN PLACE WITH TAPE WHILE DRYING.