M-92X INSTRUCTION MANUAL M009
Custom Order FINISH 11- Bright Chrome 12- Bright Brass 25- Brushed Nickel 29- Oil Rubbed Bronze GLASS 40- Clear Please keep this manual and product code number for future reference and to order replacement parts if necessary.
INSTRUCTION MANUAL ● Table of Contents GENERAL INSTRUCTIONS .................................... 3 INSTALLATION OVER CERAMIC TILES ....................... 3 NOTICE ......................................................... 3 CARE FOR YOUR FRAMELESS SHOWER DOOR ............. 3 PARTS LISTING................................................. 4 PROVIDED HARDWARE........................................ 5 TOOLS AND MATERIALS REQUIRED ......................... 5 1. DETERMINE HINGES LOCATION. .......................
INSTRUCTION MANUAL PARTS LISTING 1 2 7 8 3a 3b 3c 9 10 4 11 5 6 ITEM 12 PARTS QTY 1 SUPPORT BAR 1 2 WALL JAMB (TEMPLATE) 1 3a SIDE PANEL 1 3b EXPANDER 1 3c GASKET 1 4 TOWEL BAR 1 5 ALUMINUM “U” CHANNEL 1 6 MAGNETIC DOOR GASKET 2 7 SIDE GASKET 1 8 SQUARE WALL MOUNT HINGE 2 9 DOOR PANEL 1 10 HANDLE BAR 1 11 BOTTOM DOOR GASKET 1 12 THRESHOLD 1 4
INSTRUCTION MANUAL PROVIDED HARDWARE 13 14 15 16 17 18 19 20 ITEM HARDWARE QTY 13 CLEAR SETTING BLOCK 2 14 CLEAR SETTING BLOCK 2 15 WALL PLUG 4 16 SCREW CAP 4 17 SELF DRILLING SCREW #8-3/8 3 18 SELF-DRILLING SCREW #8-1 1/4 3 19 FLAT HEAD SCREW #6-3/4 1 20 SPACING BLOCKS 2 TOOLS AND MATERIALS REQUIRED * SCREWDRIVERS DRILL 1/4˝& 1/8˝ DRILL BITS SILICONE HAMMER * If the shower panels are to be assembled on ceramic tiles, use a 1/4˝ drill bit for ceramic tiles.
INSTRUCTION MANUAL 1 DETERMINE HINGES LOCATION. USE THE WALL JAMB (#2) AS TEMPLATE TO MARK DRILLING LOCATIONS FOR WALL-MOUNTED HINGES. Min 33 7/16˝(85cm) Max 33 7/8˝ (86cm) WALL-MOUNTED HINGES MUST BE SUPPORTED AND FASTENED INTO A STUD FRAMING. Min 33 7/16˝(85cm) Max 33 13/16˝(86cm) 1B 1A. Determine on which side the hinges will be mounted. It is recommended to install the hinges on the same side as the showerhead. 1B. Trace a centerline on the threshold and run it up along the wall. 1C.
INSTRUCTION MANUAL 2 FASTEN THE HINGES TO THE WALL. 8 2A. Fasten the hinges (#8) to the wall as illustrated. INTERIOR SHOWER SIDE 3 PREASSEMBLE THE DOOR. INTERIOR SHOWER SIDE 6 3A. 11 Temporarily insert the bottom door gasket (#11) under the door panel. LIP 7 6 20 9 9 FINAL RESULT 3B. Install the 2 spacing blocks (#7) onto the bottom lip of the gasket. INTERIOR SHOWER SIDE 3C.
INSTRUCTION MANUAL 4 INSTALL THE DOOR PANEL. 9 IT IS BEST TO HAVE 2 PEOPLE WORKING ON THIS STEP. 4B INTERIOR SHOWER SIDE 4A 4A. Place the door assembly on the shower threshold and level it. 4B. Fasten the hinges as illustrated using the Allen key. 11 20 4C. Remove the spacing blocks (#20) and the bottom door gasket (#11). 5 4C INSTALL THE DOOR HANDLE. 5A. Install the straight door handle (#10) as illustrated.
INSTRUCTION MANUAL 6 MOUNT THE WALL JAMB. NOTE CHOOSE 1 OF THE 2 HOLES AT THE TOP AND BOTTOM OF THE WALL JAMB. 6A 2 6C 6B 6D 6A. Place the wall jamb (#2) on the center of the threshold and align it using a level. Trace the outer edge of the wall jamb and the holes onto the wall. Remove the wall jamb. 6B. With a 1/4˝ drill bit, drill 3 holes into the wall using the marks as a guide. 6C. 6C(a) 6C(b) TOP VIEW TOP VIEW WALL STUD the drilled hole location, skip this step.
INSTRUCTION MANUAL 7 POSITION THE FIXED PANEL. 7B 6 7C 6 5 7A. 7A using the mallet and position the aluminium “U” (#5) underneath. 7B. 7C. Adjust and level the glass panels. The magnetic gaskets must be alligned and in contact. IF MORE ADJUSTMENTS ARE NEEDED, INSERT OTHER SETTING BLOCKS (#13&14) IN THE “U” CHANNEL.
ADDENDUM BOTTOM CLIP INSTALLATION Step 3 ON BOTH SIDE SLIDE THE FIXED PANEL OVER THE WALL JAMB 3A 3B COVER THE PLIER’S TEETH BEFOREHAND TO AVOID SCRATCHING THE ALUMINIUM PARTS.
INSTRUCTION MANUAL 8 FASTEN THE “U” CHANNEL. 8A 6 8B 2 5 8A. Mark the location of the aluminum “U” channel (#5) on 5 8B. Realign the aluminum “U” channel on the threshold and drill a hole using a 1/8˝ drill bit at about 2˝ from the edge. Put a drop of silicone in the hole and fasten the “U” channel with a 3/4˝ long screw (#19). Place the clear setting block (#14) back over the screw. 19 OPTIONAL RUN A BEAD OF SILICONE IN THE ALUMINUM “U” CHANNEL. 14 19 9 INSTALL THE FIXED PANEL.
INSTRUCTION MANUAL 10 FASTEN THE SUPPORT BAR. 1a 10B 10C 1b 10A. the shower. Level it and trace an arc on the wall. 10A 10B. Loosen the set screws in the connector (1a & 1b). 10C. Locate the screw position using the cylindrical part. With a 1/4˝ drill bit, drill a hole in the wall and insert a wall plug (#15). 10D.Put the bar back in place. Tighten all the screws.
INSTRUCTION MANUAL 11 INSTALL THE TOWEL BAR. 4 11A. Install the towel bar (#4) as illustrated. 12 INSTALL THE DOOR GASKETS. 5 6 12A INTERIOR SHOWER SIDE 45º 12B 12A. Align the bottom door gasket (#11) to the wall and project on it the 45° magnetic gasket (#6) surface. 12B.
INSTRUCTION MANUAL 12 INSTALL THE DOOR GASKETS (CONTINUED). PRIOR TO APPLY SIDE GASKET MAKE SURE THAT GLASS PANEL EDGE IS CLEAN 11 7 INTERIOR SHOWER SIDE RIGID PART 7 ± 1/8" ± 5/8" 12C ± 1/2" SUGGESTED TRIMMING 12C. Open the door and clean the door panel surface on which the door side gasket (#7) will be placed. Align gasket. Make sure it is oriented as illustrated. 12D 12D. Stick the door side gasket on the door panel.
INSTRUCTION MANUAL 13 SILICONE SEAL THE SHOWER. HOURS 13A 9 INTERIOR SHOWER SIDE 13A. Silicone seal the exterior of the shower along the wall and the aluminum “u” channel (#5). 11 13B. Position the threshold (#12) under the door panel as illustrated. Lift it to pass a bead of silicone underneath. Apply silicone on the outside edges. 12 13B WE RECOMMEND TO HOLD THE THRESHOLD (#12) IN PLACE WITH TAPE WHILE DRYING.