M-PD93X 06.
Dimensions from wall to center of threshold FRONT (DIM A) MODEL SIDE (DIM B) MIN MAX MIN MAX 4836 45 7/8” 46 3/8” 33 7/8” 34 3/8” 6036 57 7/8” 58 3/8” 33 7/8” 34 3/8” 4832 45 7/8” 46 3/8” 29 7/8” 30 3/8” 4848 45 7/8” 46 3/8” 45 7/8” 46 3/8” 6032 57 7/8” 58 3/8” 29 7/8” 30 3/8” 6048 57 7/8” 58 3/8” 45 7/8” 46 3/8” 2 PEOPLE REQUIRED
Please keep this manual and product code number for future reference and replacement parts ordering if necessary. GENERAL INSTRUCTIONS • Read this manual carefully and completely before proceeding. • It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES • Silicone should be used to seal the gap where the ceramic tiles meet the panel.
INSTALLATION MANUAL PARTS LISTING 16 1 HARDWARE 2 3 17 18 19 20 5 4 6 21 22 23 7 8 9 10 24 25 11 13 12 26 14 27 15 ITEM SUPPORT BAR 1 2 SUPPORT BAR 1 3 WALL JAMB (REGULAR PUNCH) 2 4 SIDE PANEL 1 5 RETURN PANEL 1 6 UNIVERSAL EXPANDER 2 7 GASKET 2 8 DOOR PANEL 1 9 STRAIGHT HANDLE BAR 1 10 HINGES 2 11 BOTTOM DOOR GASKET 1 12 THRESHOLD = (FINISHED WALL OPENING) 1 13 THRESHOLD = (FINISHED WALL OPENING) 1 14 MAGNETIC RETURN PANEL GASKET 1 15 MAGN
INSTALLATION MANUAL PXL4836 TOOLS AND MATERIAL REQUIRED LONG NOSE LOCKING PLIER (X2) PENCIL SCREWDRIVERS CUTTING PLIER DRILL TAPE MEASURE MALLET LEVEL BLOCK SILICONE *1/4˝& 1/8˝ DRILL BITS *To install the shower door on ceramic tiles, use a 1/4’’ drill bit for ceramic tiles INSTALLATION OF COMPONENTS STEP 1 • Wall Jamb see page 28 STEP 4 • Door panel & hinges see page 31 STEP 3 • Fix & return panel see page 30 STEP 2 • Threshold see page 29 STEP 7 • Support bar see page 34 STEP 5 • Expa
INSTALLATION MANUAL CAPRI WALL JAMB INSTALLATION 1 1a. Determine dimensions A & B on the threshold of the base. (Refer to chart on page 2 for the recommended minimum & maximum dimensions) 1b 1a Repeat on opposite side 1b. Run a second line up the wall using a level. 1c. Center the opening of the wall jamb on the line marked previously. Drill holes with a Ø1/8’’ drill bit by using the wall jamb holes as reference.
INSTALLATION MANUAL 2 THRESHOLD INSTALLATION 2a. Place silicone under the threshold. 2a INTERIOR SHOWER SIDE 2b. Place the threshold extrusion on the base by placing both 45˚ cuts together on the line of the base threshold. 2b 2c. Place the bottom glass clips and the glass panels (side panel and return panels) on the threshold extursion and mark there locations on the base. The clips must be 1” from the edge of the glass or from the expander. 2c 2d.
INSTALLATION MANUAL 3 FIX & RETURN PANEL INSTALLATION 3a. Insert the expanders into the wall jambs and the glass in the bottom glass clips. 3a 3b. Level the glass panels and lock the position by clamping the wall jambs and expanders with pliers. Cover the plier’s teeth beforehand to avoid scratching the aluminum parts. 3b 4a. Use a mallet to install the bottom gasket centered on the door panel. Place the lip side towards the inside of the shower. 4b.
INSTALLATION MANUAL DOOR PANEL INSTALLATION 4 4b GE OF ED CUT TO CUT SS F GLA GE O D TO E GLASS INTERIOR SHOWER SIDE RESULT OF OPERATION TO CUT OF EDGE S GLAS 4c 4d 4c INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE 4d 4e Q MODEL SHOWN 9
INSTALLATION MANUAL 5 INSTALLATION DES PIÈCES DE FINITIONS / FINISHING PARTS INSTALLATION SECURE THE EXPANDERS 5a. Secure the expanders with their wall jambs using the self drilling screws #8- 3/8’’ and place the caps on the heads of apparent screws.
INSTALLATION MANUAL 6 6a. Screw the handle on the door panel with the bar part facing the ouside of the shower. POIGNÉE INTÉRIEURE (1) HANDLE INSTALLATION 6a 6b. Screw the inside knob facing the inside of the shower using the plastic gaskets be tween the metal parts and the glass panel. 6c. Screw the part without grip using the thitening pin in the second hole of the door panel using the plastic gaskets between the metal parts and the glass panel.
INSTALLATION MANUAL SUPPORT BARS INSTALLATION 7 7a 7a. Loosen the glass clip (#1d). Align the slotte panel. The slotted screw head to the should be on the inside of the shower. 7b. Rest the support bar on the panel inside the tub. Level it and trace an arc on the wall. 7b 7c. Isolate the wall bracket and drill a hole, using a 1/4˝ drill bit through the wall. Locate the position of this hole by way of the wall bracket. Insert a wall plug. 7d. Secure the wall bracket to the wall by way of the screw.
INSTALLATION MANUAL SEALING 8 8a. Use a mallet to install the side gasket on the side panels. Place the textured side towards the outside of the shower. 8a INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE 8b. Use a mallet to install the magnetic gasket on the door and return panels. The magnetic gasket must close in point on the side of the handle hole. 8c. Silicone the outside of the shower, between the wall and the wall jamb, bellow of the panel and the return panel. 8b 8d.