PDR2W-4836-CW PDR2W-6036-CW PDR2W-6042-CW OWNER’S MANUAL SHOWER ENCLOSURES 2 PEOPLE REQUIRED P004 IT IS MANDATORY TO HAVE A WALL STUD TO SECURELY FASTEN THE RUNNING RAIL TO THE WALL 07.
TABLE OF CONTENTS FIXE / FIXED PANEL 1 PANNEAU PARTS LISTING ........................................................ 3 PARTS TABLE .......................................................... 4 PROVIDED HARDWARE ............................................... 5 REQUIRED TOOLS AND MATERIALS ................................. 5 WALL JAMB INSTALLATION .......................................... 6 DOOR PANEL. ......................................................... 7 RETURN PANEL..................................
PARTS LISTING 18 5 2 5 1 4 14 16b 4 16a 3 15 17 12 16c 11 8 19 6 7 13 9 10 3
Running rail Set of double rollers Wall bracket for running rail Door stopper 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16a 16b 16c 17 18 19 Threshold (return panel) Door panel side gasket Fixed panel gasket Door bottom gasket Return panel glass mount bracket Wall jamb (Flat) Universal expander Return panel Gasket Door panel Fixed panel 90º Corner Glass Clip Bottom center guide Straight handle PARTS ITEM 1 2 sets 1 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 QTY PARTS TABLE 4
HARDWARE 20 21 22 23 24 25 26 27 28 ITEM HARDWARE QTY 20 Self-drilling screw #6-1” Screw #12-3” Anchor (Blanc - White) Self drilling screw Wall plug (Orange) Self drilling screw #8 - 3/8 screw cap Hex L key 3 mm Hex L key 6mm (7/32”) 2 2 21 22 23 24 25 26 27 28 3 3 4 3 4 1 1 TOOLS * HACKSAW SCREWDRIVERS DRILL 1/4˝&�1/8˝ DRILL BITS SILICONE If the shower panels are to be assembled on ceramic tiles, use a 1/4˝ drill bit for ceramic tiles.
1 WALL JAMB INSTALLATION 1A Using a measuring tape, mark the center of the threshold of the base. 1A 1B Using the marking established in the previous step, run a second line up the wall. Use a level to ensure verticality of this line. B 1B 1C Place the wall jamb onto the wall while ensuring that the wall jamb holes align themselves onto the line running up the wall. Moreover, the side holes of the wall jamb (15) should face the interior of the shower.
2 17 2A 2A 2A 17 13 2B DOOR PANEL Using the cardboard packaging box as platform, install bottom door gasket (13) onto door panel (17) using a block and a mallet. Notice the gasket orientation. INTERIOR SHOWER SIDE 17 12 2B INTERIOR SHOWER SIDE 3A Install door side gasket (12) onto sliding door panel (17). Ensure that edge of glass is clean so as to ensure proper adhesion of the gasket.
3 CONTINUED 3D 3D Slide the return panel assembly (16a.b.c) into the wall jamb (15) so as to allow the return panel (16b), along with the clips for bottom of fixed panel (6), to rest on the threshold of the base. 15 16a.c 16b 15 3E 16a.c 3E 6 6 Mark the glass clips for bottom of fixed panel (6) locations on the base, ensuring that the leading edge of the return panel is tangent to the center of threshold of the base.
3 CONTINUED 3H 3H 16b Ensure that the return panel (16b) is vertical by way of a level. If there need be a correction, adjust the verticality of the expander (16a) in relation to the wall jamb (15). 3I 3I Once the return panel (16b) has been adjusted, secure the expander (16a) to the wall jamb (15) by way of a clamp so as to keep the return panel level. 16a.c 15 16b 3J 15 3J By way of #8- 3/8 screws (25), as well as screw caps (26), permanently secure the wall jamb (15) to the expander (16a).
4 RUNNING RAIL 4 1 4A Position the stoppers (4) on the running rail (1) as illustrated. Secure them temporarily in place. 4 E 4B E Position the wall bracket for running rail (3) on the running rail (1) as illustrated. Position the return panel glass mount bracket (14) expander (E) as shown. Secure them temporarily in place.
1 5 / FIXED PANEL Fasten the running rail (1) to the fixed panel (18) with the glass holders (5). Secure them temporarily in place. INTERIOR SHOWER SIDE Ensure that the running rail (1) is at the highest possible position in reference to the holes of the fixed panel (18). 5 5 GLASS HOLDERS 1 18 Place the glass panel onto a cushioned surface, such as a towel or cardboard so as to prevent unwanted damage.
6 FIXED PANEL 6A Position the fixed panel (18) on the threshold of the base (B) as shown. Adjust the wall bracket (3) as well as the return panel glass mount bracket (14) so as to ensure that the running rail (1) is secured. 20 The bottom guide (7) can hang off the threshold (B) as long as it can be well-fastened. 18 7 18 INTERIOR SHOWER SIDE B B 6B Ensure that the running rail (1) is level and that the fixed panel (18) is square.
6 CONTINUED 6C 3 Mark the screw locations for the wall bracket for running rail (3) on the wall as well as the placement the glass clip (6) and bottom center guide (7). 3 5 6C 6 7 7 6 7 THRESHOLD Remove the fixed panel (18) so as to allow placement of the threshold (9) onto the base. Ensure that a bead of silicone (S) is applied to the underside of the threshold before installing. S 9A 9 Secure glass clip (6) and bottom center guide (7) with self drilling screws (20) and insert gaskets.
8 3 10A FIXED PANEL 8A Remove running rail (1) from wall bracket for running rail (3) and return panel glass mount bracket (14). Drill holes in wall with a drill bit, intended for ceramic tiles, through to the wall stud. WALL STUD 3 21 Fasten the wall brackets (3) with #12-3 (21). 3 8B 18 8B Insert large fixed panel (20) back, ensuring that it’s placed in the bottom glass clip (6) and bottom center guide (7).
8 CONTINUED 8C Apply a bead of silicone at the corner of the narrow fixed panel (18) and the return panel (16c). Proceed to securing the assembly with 90° glass corner clips (19).
9 DOOR PANEL Assemble a set of double rollers (2) to the door panel’s (17) top holes, as illustrated. 2 17 9A INTERIOR SHOWER SIDE 17 9B Install door panel (17), ensuring that a set of rollers (2) are positioned over the running rail (1). 17 9B Ensure that the door panel (17) is placed within the bottom center guide (7).
9 CONTINUED WASHER 9C Install second set of double rollers (2) to the bottom holes of door panel (17), making sure that they are tangent to the running rail (1) by way of the excentric washers. 1 2 GLASS HOLE WASHER 10 STRAIGHT HANDLE Install straight handle (8) onto door panel (17). Ensure that clear washers on either side of glass are installed.
11 DOOR PANEL SIDE GASKET / FIXED PANEL Install door side gasket (11) onto sliding door panel (17). 17 11 1/2” (12.
12 STOPPERS 4 Adjust the position of the stoppers (4) so as to ensure a maximum opening and closing range. Fixed panel gasket (12) should be collapsed against wall when door is closed. 4 DOOR CLOSED 13 SILICONE Apply silicone (S) between the bottom of the fixed panel (18) and return panel (16b) and the ir appropriate thresholds (9) (10). Silicone application is also recommended along the length of both these thresholds and along the length of the wall jamb (15).
