PDR3W-6036 OWNER’S MANUAL IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS.
GENERAL INSTRUCTIONS - Read this manual carefully and completely before proceeding. - Product are subject to change without notice. Use the installation instructions supplied with the product. SAFETY - " ! - # o WATERPROOFING - .
SHOWER ENCLOSURE 16 20 13 7 3.1 11 19 3.2 15 #11 ASSEMBLY 18 11 2 1 3.3 #12 ASSEMBLY 12 18 8 17 12 4 10 9 6 14 20 5.1 5.3 2 Glass holder for fixed panel Bottom center guide 10 11 Hex L key Clear setting block Clear setting block Instruction manual 23.8 23.9 23.10 23.11 Hex L key #6-1” - Self-drilling screw 23.7 23.6 8-3/8” - Self-drilling screw 23.3 Screw cap #6-1 - Wall Plug (Orange) Back screw cap #8-1 1/4"- Self-drilling screw 23.1 23.2 23.4 HARDWARE 23 23.
TOOLS REQUIRED * SCREWDRIVERS DRILL 1/4 & 1/8 DRILL BITS FINELINER If the shower panels are to be assembled on ceramic tiles, use a 1/4 drill bit for ceramic tiles.
1 DOOR BOTTOM GASKET 5/16” 8mm INTERIOR SHOWER SIDE DOOR CLOSING ON RIGHT DOOR CLOSING ON RIGHT 2 ! ! DOOR PANEL PLACEMENT DOOR CLOSING ON LEFT ! ! DOOR CLOSING ON RIGHT CARDBOARD OR TOWEL TO PROTECT. CARDBOARD OR TOWEL TO PROTECT.
3 LOCATING ALUMINUM THRESHOLDS A DIMENSION A = RUNNING RAIL + 2 5/8’’(MIN) TO 2 7/8’’ (MAX) B DIMENSION B = RETURN PANEL + 1/4’’(MIN) TO 3/4’’(MAX) 6
4 ALUMINUM THRESHOLDS PLACEMENT 1 1/2” 38mm FROM FINISHED WALL SHOWER ENCLOSURE 1 1/2” 38mm FROM FINISHED WALL 7
1 COMPONENTS PLACEMENT 5 A PLACE AGAINST FRONT THRESHOLD ILLUSTRATION SERVES TO REPRESENT AN INSTALLATION WITH DOOR CLOSING ON LEFT. FOR DOOR CLOSING ON RIGHT, MEASURE PLACEMENT OF FRONT THRESHOLD COMPONENTS FROM LEFT THRESHOLD.
6 DRILLING EMPLOY A 1/8’’ DRILL BIT AND DRILL THROUGH THRESHOLD AND THICKNESS OF ACRYLIC. FOR CERAMIC BASE, DRILL THROUGH THRESHOLDS AND MAKE A PILOT HOLE IN THE CERAMIC TILE.
7 VHB TAPE REMOVE COMPONENTS. FOR CERAMIC BASE, PIERCE THROUGH PILOT HOLES USING 1/4’’ CERAMIC BIT AND ADD SILICONE WITHIN HOLES. INSERT INCLUDED WALL PLUGS. FOR ACRYLIC BASE, SIMPLY ADD SILICONE TO 1/8’’ HOLES. PROCEED TO CLEANING BASE THRESHOLD AS WELL AS UNIT THRESHOLDS.
8 FINAL COMPONENTS PLACEMENT SHOWER ENCLOSURE 11
9 SECURE COMPONENTS SECURE COMPONENTS USING SELF-THREADING #6-1’’ SCREWS AND SLIDE GASKETS IN PLACE.
10 WALL JAMBS SHOWER ENCLOSURE 13
10 WALL JAMBS INTERIOR SHOWER SIDE 14
11 WALL JAMBS SHOWER ENCLOSURE 15
12 RETURN PANELS 3/16’’ 16
12 RETURN PANELS TEMPORARILY SECURE.
13 RETURN PANEL GLASS BRACKETS 3’’ 18
14 RUNNING RAIL SHOWER ENCLOSURE 19
14 RUNNING RAIL MANEUVER RUNNING RAIL CAREFULLY.
15 FIXED PANEL TEMPORARILY SECURE.
15 FIXED PANEL IF LEVEELING NECESSARY.
16 CORNER CLIPS SHOWER ENCLOSURE 23
17 TOP ROLLERS 24
18 DOOR INSTALLATION DOOR AT MAXIMUM HEIGHT SHOWER ENCLOSURE DOOR AT MINIMUM HEIGHT 25
19 BOTTOM ROLLERS 26
20 DOOR HANDLE *MODEL ILLUSTRATED A SHOWER ENCLOSURE ! 27
21 MIDDLE GASKET 1’’ 28
22 DOOR GASKET DOOR PANEL CUT SOFT PORTION TO EDGE OF BASE SHOWER ENCLOSURE CUT ADHESIVE PORTION TO DOOR PANEL EDGE 29
23 STOPPERS 30
24 WALL JAMB SECURING SHOWER ENCLOSURE 31
25 SILICONE HOURS 32
