Alvarion BreezeNET B300 Technical User Manual Software Version: 1.
Document History Document History Changed Item Description Date First revision Document’s first revision April 2009 Alvarion BreezeNET B300 ii Technical User Manual
Legal Rights Legal Rights © Copyright 2009 Alvarion Ltd. All rights reserved. The material contained herein is proprietary, privileged, and confidential and owned by Alvarion or its third party licensors. No disclosure thereof shall be made to third parties without the express written permission of Alvarion Ltd. Alvarion Ltd. reserves the right to alter the equipment specifications and descriptions in this publication without prior notice.
Legal Rights invoice date (the "Warranty Period")". During the Warranty Period, Alvarion may release to its Customers firmware updates, which include additional performance improvements and/or bug fixes, upon availability (the "Warranty"). Bug fixes, temporary patches and/or workarounds may be supplied as Firmware updates. Additional hardware, if required, to install or use Firmware updates must be purchased by the Customer.
Legal Rights WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO WARRANTIES, TERMS OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, NON-INFRINGEMENT, AND ACCURACY OF INFORMATION GENERATED. ALL OF WHICH ARE EXPRESSLY DISCLAIMED. ALVARION' WARRANTIES HEREIN RUN ONLY TO PURCHASER, AND ARE NOT EXTENDED TO ANY THIRD PARTIES.
Legal Rights Disposal of Electronic and Electrical Waste Disposal of Electronic and Electrical Waste Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product.
Important Notice Important Notice This user manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information belonging to Alvarion Ltd. Such information is supplied solely for the purpose of assisting properly authorized users of the respective Alvarion products.
About this Manual About this Manual This User Manual is a description of Alvarion devices and contains installation and configuration guidelines, recommendations and troubleshooting sections, and supplementary materials. The document is intended to be used by Qualified RF engineers/technicians and IT professionals.
Contents Contents Chapter 1 - Getting Started ..................................................................... 1 1.1 Scope of Document....................................................................................................3 1.2 Abbreviations .............................................................................................................4 1.3 Document Marks ........................................................................................................
Contents 2.5.2 Pole Mounting Kit Assembling ..........................................................................27 2.6 Mounting Kits Assembling ......................................................................................28 2.6.1 Pole Mounting Kit MONT-5000-V.Pole-KIT for Vertical Mast............................28 2.6.2 Pole Mounting Kit MONT-5000-H.Pole-KIT for Horizontal Pole........................29 2.7 Specifications .....................................................................
Contents Chapter 5 - Configuration Via Web Interface........................................ 66 5.1 Overall Functionality Overview...............................................................................68 5.2 Run Requirements ...................................................................................................69 5.3 Basic Settings...........................................................................................................70 5.4 Device Status...............................
List of Tables List of Tables Table 2-1: ODU LED Indicators Description................................................................................ 12 Table 2-2: RJ-45 Connector Soldering Procedure ...................................................................... 18 Table 2-3: Radio Specifications................................................................................................... 31 Table 2-4: Maximum Peak Channel Power Levels ........................................................
List of Figures List of Figures Figure 2-1: IDU-BS Top View........................................................................................................ 8 Figure 2-2: IDU-BS Front Panel .................................................................................................... 8 Figure 2-3: IDU-BS Rear Panel..................................................................................................... 9 Figure 2-4: Connection scheme for IDU-BS......................................
List of Figures Figure 4-4: Muffer Review Mode ................................................................................................. 55 Figure 4-5: Muffer MAC2 Mode................................................................................................... 56 Figure 4-6: Muffer Statistics Mode .............................................................................................. 57 Figure 4-7: Load Meter.............................................................................
Chapter 1 Getting Started
Chapter 1 - Getting Started In This Chapter: “Scope of Document” on page 3 “Abbreviations” on page 4 “Document Marks” on page 5 Alvarion BreezeNET B300 2 Technical User Manual
Chapter 1 - Getting Started 1.1 Scope of Document Scope of Document This document consists of the following chapters: “Getting Started” on page 1 - This chapter includes the information about this document purpose and structure. “Hardware Description” on page 6 - This chapter shows the devices appearance and all plugs and connectors.
Chapter 1 - Getting Started 1.
Chapter 1 - Getting Started 1.3 Document Marks Document Marks CAUTION All caution warnings are marked with a special warning sign. One should pay a great deal of attention to what is written in the Warning sections. NOTE All notes are marked with a special note sign. Notes usually contain useful comments or hints to the described section of the document.
Chapter 2 Hardware Description
Chapter 2 - Hardware Description In This Chapter “Power supply units (IDU)” on page 8 “Outdoor Units (ODU)” on page 10 “Installation Preparations” on page 13 “BU/RB-B300D-5X” on page 21 “BU/RB-B300-5X” on page 25 “Mounting Kits Assembling” on page 28 Alvarion BreezeNET B300 7 Technical User Manual
Chapter 2 - Hardware Description Power supply units (IDU) 2.1 Power supply units (IDU) 2.1.
Chapter 2 - Hardware Description Power supply units (IDU) Figure 2-3: IDU-BS Rear Panel Figure 2-4: Connection scheme for IDU-BS Alvarion BreezeNET B300 9 Technical User Manual
Chapter 2 - Hardware Description Outdoor Units (ODU) 2.2 Outdoor Units (ODU) 2.2.
Chapter 2 - Hardware Description Outdoor Units (ODU) Figure 2-6: BU/RB-B300D-5X Top View 2.2.
Chapter 2 - Hardware Description Outdoor Units (ODU) Figure 2-8: BU/RB-B300-5X Top View 2.2.3 ODU LED Indicators Description ODU units have two LED indicators (red and green) located in the Console connector. These LEDs are useful in monitoring the device status during the installation procedure.
Chapter 2 - Hardware Description Installation Preparations 2.3 Installation Preparations 2.3.1 Required Components and Accessories Before the installation, please make sure you have all necessary parts and accessories: Device Antenna Low loss antenna cable for the required frequency range Antenna pole (if necessary) Required grounding system Accessories and tools 2.3.
Chapter 2 - Hardware Description Installation Preparations Power lines To obtain the best results, it is necessary to perform a precise analysis of a signal propagation path zone and possible obstructions that may cover a part of the 1st Fresnel zone (usually the analysis is performed at the highest points of the signal propagation path).
Chapter 2 - Hardware Description 2.3.3 Installation Preparations Antenna Poles Usage Antenna installation is performed on a special facility called antenna pole. The pole is used for strong antenna tightening at the installation site. Poles might have different modifications depending on the installation requirements. 2.3.
Chapter 2 - Hardware Description Installation Preparations CAUTION Antenna pole, tower, ODU and lightning arrestor should be connected to the first common grounding contour. Cable thickness should be no less than 10AWG using corrosion-steady connectors. It is highly recommended to entrust grounding contour development to the skilled personnel. A special attention should be paid if antenna used is not DC-shorted. In this case additional lightning arrestor should be used between the antenna and ODU.
Chapter 2 - Hardware Description Installation Preparations Use GPS receiver and area map Use build-in Device features. These features allow evaluating current channel/signal quality and perform precise antenna alignment 2.3.9 Precaution Measures Before you start the installation please read this section very carefully. Antennas are installed on the roof tops or on the building walls. This work must be accomplished only by personnel having special skills and experience in this area.
Chapter 2 - Hardware Description Installation Preparations Table 2-2: RJ-45 Connector Soldering Procedure Illustration Description Step 1. Peel STP service cable and prepare "RJ-45" connector parts. Use RJ-45 connector without grounding here (RJ-45 connector with grounding is used for connecting service cable to IDU). Step 2. Stick rubber filler - 5 on the Part 4, previously having removed protective white layer from rubber filler -5. Insert Part 2 inside part 4 up to the stop.
Chapter 2 - Hardware Description Installation Preparations Table 2-2: RJ-45 Connector Soldering Procedure Illustration Description Step 4. Put Part 4 on the attached in the previous step RJ-45 connector. Step 5. Screw Part 2 on Part 4. This fixes the "RJ-45" connector on the cable. Check that the connector is properly fixed on the cable. Step 6. Assemble the connector to the unit.
Chapter 2 - Hardware Description Installation Preparations Table 2-2: RJ-45 Connector Soldering Procedure Illustration Description Step 7. Fix the connector by screwing Part 3. Now the connector is hermetically attached to the unit. 2.3.
Chapter 2 - Hardware Description BU/RB-B300D-5X 2.4 BU/RB-B300D-5X 2.4.1 Installation Guidelines 1 Unpack the equipment 2 Check items integrity 3 Prepare RF-cables of the required length. The recommended maximal RF cable length is 1 meter. 4 Install and isolate the connectors on the RF cables Figure 2-10: BU/RB-B300D-5X Installation 1 5 Determine the STP cable length that is used to connect IDU and ODU.
Chapter 2 - Hardware Description BU/RB-B300D-5X 11 Connect the ODU-IDU cable to the ODU 12 Isolate the ODU connector joint place 13 Once the antenna and antenna pole are installed they must be grounded via lightning protection grounding contour. Antenna's position must be lower than the highest antenna pole point at least by 2 antenna heights.
Chapter 2 - Hardware Description BU/RB-B300D-5X 19 Connect Ethernet cable to IDU 20 Provide power supply for IDU 21 Connect to the Device using Telnet protocol CAUTION It is extremely important to install ODU connectors down! 2.4.
Chapter 2 - Hardware Description BU/RB-B300D-5X Figure 2-13: Tube Mounting 2 Alvarion BreezeNET B300 24 Technical User Manual
Chapter 2 - Hardware Description BU/RB-B300-5X 2.5 BU/RB-B300-5X 2.5.1 Installation Guidelines 1 Unpack the equipment 2 Check items integrity 3 Determine the STP cable length that is used to connect IDU and ODU. The total cable length between LAN (behind IDU) and ODU should not be longer than 100 meters.
Chapter 2 - Hardware Description BU/RB-B300-5X 8 Connect the ODU-IDU cable to the ODU 9 Isolate the ODU connector joint place 10 Once the ODU and antenna pole are installed they must be grounded via lightning protection grounding contour.
Chapter 2 - Hardware Description 2.5.
Chapter 2 - Hardware Description Mounting Kits Assembling 2.6 Mounting Kits Assembling 2.6.1 Pole Mounting Kit MONT-5000-V.Pole-KIT for Vertical Mast CAUTION Attention! Pole mounting kit MONT-5000-V.Pole-KIT does NOT contain metal straps. Figure 2-18: MONT-5000-V.
Chapter 2 - Hardware Description Mounting Kits Assembling Figure 2-19: MONT-5000-V.Pole-KIT 2 2.6.2 Pole Mounting Kit MONT-5000-H.Pole-KIT for Horizontal Pole CAUTION Attention! Pole mounting kit MONT-5000-H.Pole-KIT does NOT contain metal straps.
Chapter 2 - Hardware Description Mounting Kits Assembling Figure 2-20: MONT-5000-H.Pole-KIT 1 Figure 2-21: MONT-5000-H.
Chapter 2 - Hardware Description Specifications 2.7 Specifications 2.7.1 Radio Table 2-3: Radio Specifications Item Description Frequency ETSI (5.470 - 5.725 GHz) Center frequencies range 5.475 - 5.720 GHz (in 5MHz steps) for 5MHz BW Center frequencies range 5.475 - 5.720 GHz (in 5MHz steps) for 10MHz BW Center frequencies range 5.480 - 5.700 GHz (in 20MHz steps) for 20MHz BW Center frequencies range 5.490 - 5.690 GHz (in 20MHz steps) for 40MHz BW ETSI (5.725 - 5.
Chapter 2 - Hardware Description Specifications Table 2-3: Radio Specifications Item Description FCC (5.250 - 5.350 GHz) Center frequencies range 5.255 - 5.345 GHz (in 5MHz steps) for 5MHz BW Center frequencies range 5.255 - 5.345 GHz (in 5MHz steps) for 10MHz BW Center frequencies range 5.260 - 5.340 GHz (in 20MHz steps) for 20MHz BW Center frequencies range 5.270 - 5.330GHz (in 20MHz steps) for 40MHz BW FCC (5.470 - 5.725 GHz) Center frequencies range 5.475 - 5.
Chapter 2 - Hardware Description Specifications Table 2-3: Radio Specifications Item Description Output Power (at antenna port) Up to 18 dBm (dependant upon regulation) Table 2-4: Maximum Peak Channel Power Levels 2.7.2 Channel Bandwidth Max. Total Channel Power (Peak) (dBm) 5 MHz 25.6 10 MHz 24.18 20 MHz 23.58 40 MHz 21.8 Antenna Table 2-5: Antenna Specifications 2.7.3 Item Description External Antenna ANT, T.S, 4.9-6 GHz, 9°, dual polarized, 23 dBi / ANT, T.S, 4.
Chapter 2 - Hardware Description 2.7.
Chapter 2 - Hardware Description 2.7.7 Specifications Standards and Regulations Table 2-10: Standards and Regulations Compliance Item Description Radio ETSI EN 301 893 V1.5.1 / ETSI EN 302 502 V1.2.1 EMC ETSI EN 301 489-1 V1.4.
