User's Manual

ManualsBrandsAlvarion Technologies ManualsElectronicsIP Broadband Wireless Access System

Table Of Contents

BreezeACCESS V

System Manual

Cat. No. 213283

Summary of content (268 pages)

PAGE 1
BreezeACCESS V System Manual Cat. No.
PAGE 2
PAGE 3
© 2002 by Alvarion Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names BreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW, BreezeMANAGE, BreezeCONFIG and BreezeWIZARD are trade names of Alvarion Ltd. Other brand and product names are registered trademarks or trademarks of their respective companies. Statement of Conditions The information contained in this manual is subject to change without notice.
PAGE 4
ii BreezeACCESS 4.0 System Description Electronic Emission Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules.
PAGE 5
Important Notice iii Outdoor Unit and Antenna Installation and Grounding Be sure that the outdoor unit, the antenna and the supporting structure are properly installed to eliminate any physical hazard to either people or property. Verify that the outdoor unit and the antenna mast (when using external antenna) are grounded so as to provide protection against voltage surges and static charges.
PAGE 6
BreezeACCESS 4.0 System Description iv Important Notice This user's manual is applicable to BreezeACCESS units using software version 4.1 or later and is delivered subject to the following conditions and restrictions: ! This manual contains proprietary information belonging to Alvarion Ltd. Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of BreezeACCESS.
PAGE 7
Table of Contents System Manual Book 1: System Description Introduction .............................................................1-1 Introducing BreezeACCESS .....................................................1-2 System Components .............................................................2-1 Subscriber Units (Customer Premises Equipment) ...............2-2 Base Station Equipment ...........................................................2-4 Networking Equipment ....................................
PAGE 8
System Manual Book 2: Installation IF-Based Equipment ................................................................1-1 Packing Lists ..............................................................................1-2 Guidelines for Selection of Equipment Locations ..................1-5 Installing the Outdoor Unit .......................................................1-7 Installing the SU-NI and AU-NI Indoor Unit ...........................1-12 Installing Modular Base Station Equipment ....................
PAGE 9
System Manual Book 3: Commissioning Setting Basic Parameters ....................................................1-1 Accessing the Monitor Program ..............................................1-2 Configuring Basic Parameters in Access and Subscriber Units ...................................................1-5 Configuring Parameters in GU-A-BS Units ...........................1-10 Optimizing the Wireless Link .....................................................
PAGE 10
System Manual Book 4: Operations and Administration Accessing the Monitor Program ......................................................1-1 Accessing the Monitor Program using the RS 232 MON Connector ............................................................1-2 Accessing the Monitor Program using Telnet ........................1-4 Operating the Monitor Program ...............................................1-6 Menus and Parameters .......................................................2-1 Main Menu ....
PAGE 11
Table of Contents System Manual: Appendices Appendix A: Software Version Loading Procedure ..................................................A-1 General ...................................................................................... A-1 Loading an Upgrade to a Unit with FLASH Type: F .............. A-3 Loading an Upgrade to a Unit with FLASH Type: S .............. A-5 Appendix B: Supported MIBs and Traps .................................................................
PAGE 12
x BreezeACCESS 4.
PAGE 13
BreezeACCESS V System Manual Book 1: System Description
PAGE 14
PAGE 15
System Description Table of Contents Introduction .............................................................1-1 Introducing BreezeACCESS .....................................................1-2 System Components .............................................................2-1 Subscriber Units (Customer Premises Equipment) ...............2-2 SU-A/E Units with an Outdoor Radio Unit and Antenna .....2-2 Base Station Equipment ...........................................................
PAGE 16
ii BreezeACCESS 4.
PAGE 17
Chapter 1 Introduction About This Chapter This chapter introduces the BreezeACCESS system, its components and its functions.
PAGE 18
BreezeACCESS 4.0 System Description 1-2 Introducing BreezeACCESS BreezeACCESS IP Broadband Wireless Access system is an IP based access system that supports wireless data and voice services, employing wireless packet-switched data technology to support high-speed IP services, including fast access to the Internet and Virtual Private Networks. BreezeACCESS users are provided with a network connection that is always on, supporting access to the Internet and other IP services at data rates of up to 3 Mbps.
PAGE 19
Chapter 2 System Components About This Chapter This chapter describes the BreezeACCESS system components. It includes the following sections: ! Subscriber Units (Customer Premises Equipment)‚ page 2-2, describes BreezeACCESS equipment installed at the customer’s premises. ! Base Station Equipment‚ page 2-4, describes the equipment used in BreezeACCESS Base Stations.
PAGE 20
BreezeACCESS 4.0 System Description 2-2 Subscriber Units (Customer Premises Equipment) The BreezeACCESS Subscriber Unit (SU) installed at the customer premises provides data only or data and telephone connections. The data connection is a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface while the voice connection (in units that support voice) is a standard RJ 11 Plain Old Telephone (POTS) interface.
PAGE 21
System Components 2-3 Figure 2-1: BreezeACCESS SU-A/E Outdoor and Indoor Units The following products are available: Data-only Units: SU-X-1D-5.7 The unit supports one Ethernet device. SU-X-8D-5.7 The unit supports up to eight Ethernet devices (eight MAC addresses). SU-X-BD-5.7 The unit provides bridge functionality and can support up to a full LAN. Data and Voice Units: SU-X-1D1V-5.7 The unit supports one Ethernet device and has an interface to a standard analog telephone set (POTS).
PAGE 22
BreezeACCESS 4.0 System Description 2-4 Base Station Equipment The BreezeACCESS Access Units (AU) installed at the base station site provide all the functionality necessary to communicate with the remote Subscriber Units as well as to connect to the backbone of the service provider. Each AU connects to the network through a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface.
PAGE 23
System Components 2-5 Figure 2-2: BreezeACCESS Base Station Module and Outdoor Unit GU-A-BS GPS and Alarms System The optional GU-A-BS system can be used to synchronize the frequency hopping mechanisms of collocated AU-E-BS BreezeACCESS units (where such synchronization is permitted by local regulations) as well as to provide alarm management. The GU-A-BS system is comprised of two units: ! An outdoor GPS Receiver and Antenna unit, the GU-RA. ! An indoor GPS and Alarms module, the BS-GU.
PAGE 24
BreezeACCESS 4.0 System Description 2-6 Figure 2-3: BreezeACCESS GU-A-BS System Components The BreezeACCESS BS-GU module is designed to be inserted into the BS-SH 19” base station chassis to provide hopping synchronization signals to the BS-AU Access Unit modules. The card uses timing signals derived from signals received from the GU-RA GPS antenna. These signals, generated by the GPS global satellites network, allow accurate synchronization of systems located in different locations.
PAGE 25
System Components 2-7 Daisy-chained BS-GU modules use the synchronization signals generated by the first unit in the chain (the Master unit). The BS-GU module also supports the management of alarm inputs and outputs. The module receives Alarms In indications from other BreezeACCESS modules in the base station shelf (internal alarms) and external alarms from other devices via the AL IN connector.
PAGE 26
BreezeACCESS 4.0 System Description 2-8 Networking Equipment The base station equipment is connected to the backbone through standard data communication and telecommunication equipment. For improved security, the 10BaseT ports of the AU modules are connected directly to a multi-port router. This router is connected by any means of point-to-point link to the backbone.
PAGE 27
System Components 2-9 Management Systems The end-to-end IP based architecture of the system allows full management of all components from any point in the system. BreezeACCESS components can be managed using standard management tools through SNMP (Simple Network Management Protocol) agents that implement standard and proprietary MIBs for remote setting of operational modes and parameters.
PAGE 28
BreezeACCESS 4.0 System Description 2-10 BreezeCONFIG The BreezeCONFIG ACCESS configuration utility can also be used to manage BreezeACCESS system components. It is an SNMP-based application that provides a consistent view of the network and the system administrator can use it to control a large number of units from a single location.
PAGE 29
Chapter 3 Specifications About This Chapter This chapter lists the technical specifications of BreezeACCESS and includes the following sections: ! System Specifications‚ page 3-2, outlines the technical specifications of the BreezeACCESS system. ! Physical Specifications‚ page 3-6, lists the physical and electical specifications for different types of BreezeACCESS units.
PAGE 30
BreezeACCESS 4.0 System Description 3-2 System Specifications Radio and Modem Frequency INT Mode: 5.725-5.875 GHz US Mode: 5.725-5.710 GHz Operation Mode Time Division Duplex Radio Access Method FH-CDMA Standard Compliance FCC Part 15.
PAGE 31
Specifications 3-3 Data Communication Standard Compliance IEEE 802.3 CSMA/CD VLAN support Based on IEEE 802.1Q Layer-2 Traffic Prioritization Based on IEEE 802.1p Layer-3 Traffic Prioritization ToS according to RFC791 MIR (Maximum Information Rate) and CIR (Committed Information Rate) Programmable for each user, separately for uplink and downlink. Range: 0 – 2200 Kbps, 1 Kbps resolution. Voice/Fax (Subscriber Units with voice support) Standard Compliance ITU-T H.323 Ver.
PAGE 32
BreezeACCESS 4.0 System Description 3-4 IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS) IF Frequency 440 MHz IF Cable Impedance 50 ohm Maximum IF Cable Attenuation 15 dB Maximum IF Cable DC Resistance 1.5 ohm Configuration and Management Management Options a. Via the MON port, using terminal emulation with the built-in monitor program b. Telnet, using the monitor program c. TFTP, using the Configuration upload/download utility d.
PAGE 33
Specifications 3-5 GU-RA to BS-GU Communication Physical interface RS 422 Cable Type EIA RS 422 3 x 2 x 26AWG + 1 x 2 x 24 AWG FTP Shielded.
PAGE 34
BreezeACCESS 4.0 System Description 3-6 Physical Specifications SU-A/E Subscriber Unit Connectors Unit Connector Description SU-NI IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs.
PAGE 35
Specifications 3-7 AU-E-NI Stand-Alone Access Unit Connectors Unit Connector Description AU-NI IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs Cable connection to a PC: crossed DC-12 V DC phone jack for the AU-PS power supply MON RS 232, 3-pin low profile jack IF TNC jack, 50 ohm, lightning protected ANT N-Type jack, 50 ohm, lightning protected AU-RE Electrical Unit Details General Power consumption: 25 W AU-NI External power supply AC inpu
PAGE 36
BreezeACCESS 4.
PAGE 37
Specifications 3-9 Modular Base Station Equipment - Electrical Unit Details General 250 W for a fully equipped chassis (1 PS, 6 AU, 1 GU) BS-PS DC power input: -48 V, 5.2 A max. DC power output: 12 V; 5 V BS-PS-AC AC power input: 85-256 VAC, 47-65 Hz, DC power output: 12 V; 5 V; 3.
PAGE 38
3-10 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 39
BreezeACCESS V System Manual Book 2: Installation
PAGE 40
PAGE 41
Installation Table of Contents IF-Based Equipment ................................................................1-1 Packing Lists ..............................................................................1-2 SU-A/E Subscriber Unit ......................................................1-2 Modular Base Station Equipment .......................................1-2 Standalone AU-E-NI Access Unit .......................................1-3 Other Items Required for Installation ...............................
PAGE 42
ii BreezeACCESS 4.
PAGE 43
Chapter 1 IF-Based Equipment About This Chapter This chapter describes the basic installation of BreezeACCESS IF-based equipment, including SU-A/E subscriber units, modular base station equipment and stand-alone AU-E-NI access units. It includes the following sections: ! Packing Lists‚ page 1-2, lists the equipment that is packed with each BreezeACCESS IF-based unit.
PAGE 44
BreezeACCESS 4.
PAGE 45
IF Based Equipment 1-3 BS-PS-AC Power Supply (one or two per chassis) ! BS-PS-AC power supply module ! AC power cable GU-A-BS GPS and Alarms System ! BS-GU module ! GU-RA GPS antenna and receiver ! 1” threaded mounting pole for the GU-RA GPS antenna ! Antenna Mounting kit Standalone AU-E-NI Access Unit ! AU-RE with a connector to an external antenna (not included) ! Pole mounting kit for the outdoor unit ! AU-NI indoor unit ! Wall mounting kit for the AU-NI unit ! AU-PS power supply with a mains power c
PAGE 46
BreezeACCESS 4.0 Installation 1-4 Items marked with an asterisk (*) are available as options from Alvarion. NOTE: The BS-GU does not have an external Monitor port and it should be configured via the Ethernet port using Telnet. Table 1-1: Required type of Ethernet cable Unit Type Connection to a PC Connection to a hub Subscriber Unit Straight Crossed Access Units Crossed Straight GPS module Straight Crossed Manual Revision: 1.
PAGE 47
IF Based Equipment 1-5 Guidelines for Selection of Equipment Locations NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS product warranty and may expose the end user or the service provider to legal and financial liabilities.
PAGE 48
BreezeACCESS 4.0 Installation 1-6 440 MHz. The maximum allowed attenuation of the IF cable connecting the outdoor unit to the indoor unit is 15 dB at 440 MHz, and the maximum allowed DC resistance (the sum of the DC resistance of the inner and outer conductors) is 1.5 ohm. This allows for cable length of up to 30 m when using the standard RG 58 cable. If longer cables are required, a cable with lower attenuation and/or DC resistance should be used.
PAGE 49
IF Based Equipment 1-7 Installing the Outdoor Unit NOTE: SU-RE and AU-RE units must be installed by a professional installer only. The Outdoor Unit Bottom Panel The SU-RA outdoor unit includes the radio and an integral high-gain flat antenna located on the front of the unit. The SU-RE and AU-RE outdoor radio units have an RF connector for connection to an external antenna.
PAGE 50
BreezeACCESS 4.0 Installation 1-8 Table 1-4: SU-RA/RE Bar Display Description LED Description Functionality Yellow LED Power On – power is present Off – power is not received from the indoor unit 8 Green LEDs Received signal strength indication Received RF signal level indication in 4 dB resolution, starting from –91 dBm Red LED High RF signal level Received signal level is –40 dBm or higher Figure 1-2: AU-RE Bottom Panel Manual Revision: 1.
PAGE 51
IF Based Equipment 1-9 Table 1-5: AU-RE LEDs Name Description Functionality ETH Ethernet activity Blinking – Data received from or transmitted to Ethernet LAN Off – No activity on the Ethernet LAN 12V IN Power On – 12 VDC power is supplied to the unit Off – 12 VDC power is not available ALARM Alarm indication On – A problem with the power amplifier or in the locking process of any of the synthesizers Off – Normal operation Pole Mounting the Outdoor Unit The outdoor unit can be secured to the p
PAGE 52
BreezeACCESS 4.0 Installation 1-10 Figure 1-3: Holes/Grooves/Screw Holes Figure 1-4: 3" Pole Mounting Installation Using the Special Brackets NOTE: When inserting the open-ended screws, make sure to insert them with the grooves pointing outwards; these grooves are intended to allow fastening of the screws with a screwdriver. Manual Revision: 1.
PAGE 53
IF Based Equipment 1-11 Connecting the Antenna Cable (SU-RE and AU-RE) Connect an RF cable between the ANT connector (located on the top panel of the unit) and the antenna. Connecting the Ground and IF Cables The ground terminal (marked ) and the IF cable connector (marked IF) are located on the bottom panel of the unit. 1. Connect one end of the ground cable to the ground terminal and tighten the ground screw firmly. Connect the other end of the ground cable to a protective ground connection. 2.
PAGE 54
BreezeACCESS 4.0 Installation 1-12 Installing the SU-NI and AU-NI Indoor Unit Figure 1-5: SU-NI with Voice Support Rear Panel Figure 1-6: SU-NI/AU-NI Front Panel NOTE: The rear panel pictured above in Figure 1-5 is a SU-NI with voice support; AU-NI units and SU-NI units that belong to Subscriber Units without voice support are identical, except that they have no TEL port. Manual Revision: 1.
PAGE 55
IF Based Equipment 1-13 Table 1-6: SU-NI/AU-NI LEDs Name Description Functionality PWR Power Supply On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit. Off – Power off or failure to supply 12 VDC to the outdoor unit.
PAGE 56
BreezeACCESS 4.0 Installation 1-14 Installing Modular Base Station Equipment BS-SH Slot Assignments The base station chassis has ten slots. Figure 1-7: BS-SH Chassis Slot Assignments The two wide slots on both sides of the shelf accommodate the BS-PS or BS-PS-AC power supply modules. The shelf is designed to support power supply redundancy through the use of two power supply modules. If a single power supply is used, it can be inserted in any of the two available slots.
PAGE 57
IF Based Equipment 1-15 Figure 1-8: BS-PS Front Panel The BS-PS provides a power input connector (marked -48V) for connecting the -48VDC power source to the module. The color codes of the cable wires are: Black Red -48 VDC + (Return) The power switch turns the mains power to the power supply ON and OFF.
PAGE 58
BreezeACCESS 4.0 Installation 1-16 Figure 1-9: BS-PS-AC Front Panel The BS-PS-AC provides a power input connector (marked AC IN) for connecting the AC power cable to the mains. The ON/OFF power switch controls the connection of the mains power to an AC to DC converter. Table 1-8: BS-PS-AC LEDs Functionality Name Description 3.3V Green LED. Indicates that the 3.3V power supply module is OK (3.3V power supply is not used by current BreezeACCESS modules) 5V Green LED.
PAGE 59
IF Based Equipment 1-17 WARNING: If two power supply modules are used in the same chassis for redundancy, both power supplies must be of the same type. Do not use a mix of AC and DC power supply modules in the same chassis. The BS-AU Figure 1-10: BS-AU Front Panel BreezeACCESS 4.
PAGE 60
BreezeACCESS 4.0 Installation 1-18 Table 1-9: BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
PAGE 61
IF Based Equipment 1-19 3. Carefully insert the BS-PS or BS-PS-AC Power Supply and the BS-AU modules into their intended slots and push firmly until they are securely locked. Before inserting the modules, verify that the switches of all BS-AU modules are in the OFF position. Close the captive screws attached to each module. Place blank covers over all the unused slots. 4.
PAGE 62
BreezeACCESS 4.0 Installation 1-20 Installing the GU-A-BS GPS and Alarms System BS-GU Front Panel Figure 1-11: BS-GU Front Panel Manual Revision: 1.
PAGE 63
IF Based Equipment 1-21 Table 1-10: BS-GU Connectors Connector Name Functionality SYNC IN Receives signals from the GPS antenna unit. If more than one collocated BS-GU module uses a single GPS antenna, this connector is used by a “Slave” unit to receive synchronization signals from the “Master” unit. SYNC OUT Sends synchronization signals to “Slave” BS-GU modules. AL IN Four connections to receive indications from external devices. AL OUT Three relay outputs to external devices.
PAGE 64
BreezeACCESS 4.0 Installation 1-22 Installing the GU-RA GPS Antenna 1. Screw the GPS antenna firmly to the special 1” threaded pole. 2. Use the mounting kit supplied with the unit (or any other suitable means) to secure the GPS antenna pole to an existing pole (e.g. any pole used for mounting base station antennas or the outdoor units of the BreezeACCESS Access Units).
PAGE 65
IF Based Equipment 1-23 NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS product warranty and may expose the end user or the service provider to legal and financial liabilities.
PAGE 66
1-24 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 67
BreezeACCESS V System Manual Book 3: Commissioning
PAGE 68
Using This Guide After completing the installation process as described in Book 2: Installation, the basic parameters must be configured to ensure that the unit operates properly and to provide wireless connectivity. Once the basic parameters have been configured properly, additional parameters can be remotely configured via either the Ethernet port or the wireless link using Telnet or SNMP management.
PAGE 69
Commissioning Table of Contents Setting Basic Parameters ....................................................1-1 Accessing the Monitor Program ..............................................1-2 Accessing the Monitor Program using the RS 232 MON Connector ....................................................1-2 Accessing the Monitor Program using Telnet .....................1-4 Operating the Monitor Program ..........................................
PAGE 70
ii BreezeACCESS 4.
PAGE 71
Chapter 1 Setting Basic Parameters About This Chapter This chapter explains how to configure the basic parameters of the BreezeACCESS system and includes the following section: ! Accessing the Monitor Program‚ page 1-2, explains how to access your BreezeACCESS units for configuration. ! Configuring Basic Parameters in Access and Subscriber Units‚ page 1-5, outlines the basic configuration process for BreezeACCESS AU and SUs.
PAGE 72
BreezeACCESS 4.0 Commissioning 1-2 Accessing the Monitor Program Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. 2. Run a terminal emulation program (such as HyperTerminal™). 3.
PAGE 73
Setting Basic Parameters 1-3 Table 1-1: Default Passwords Access Rights Password Read Only public Installer user Administrator private NOTE: Following three unsuccessful login attempts (using incorrect passwords) from either the monitor port or via Telnet, the monitor program will be blocked for five minutes. To access the monitor program during this time, the unit must be reset (via SNMP or by disconnecting/reconnecting power). BreezeACCESS/AU-BS Official Release Version – 4.0.
PAGE 74
BreezeACCESS 4.0 Commissioning 1-4 NOTE: The Main Menu of the GU-BS (GPS and Alarms module) does not include the Basic Configuration option. Accessing the Monitor Program using Telnet 1. Connect a PC to the Ethernet port of the unit. See the table below to determine the type of cable. Configure the PC’s IP parameters to enable connectivity with the unit (the default IP Address is 10.0.0.1). Run the Telnet application.
PAGE 75
Setting Basic Parameters 1-5 Configuring Basic Parameters in Access and Subscriber Units Introduction The Basic Configuration menu includes all the parameters that are necessary for the initial installation and operation of BreezeACCESS units. Once the unit is properly installed and operational, other parameters can be configured using the monitor program or via either the Ethernet port or the wireless link using Telnet or SNMP management.
PAGE 76
BreezeACCESS 4.0 Commissioning 1-6 " From the Basic Configuration menu, select Access to DHCP. The Access to DHCP menu opens. Select the required access option: From Ethernet Port Only, From Wireless Port Only or From Both Ethernet and Wireless Ports. " From the Basic Configuration menu, select IP Address. The IP Address configuration screen appears. Enter the required IP address. " From the Basic Configuration menu, select Subnet Mask. The Subnet Mask configuration screen appears.
PAGE 77
Setting Basic Parameters 1-7 Configuring Frequency Hopping Parameters 1. In units where Hopping Band selection is available, select Hopping Band from the Basic Configuration menu. The Hopping Band configuration screen appears. Enter the required hopping band option: ISM US FCC, ISM International or Flexible Hopping Definition. ! If the selection in the Hopping Band configuration screen was Flexible Hopping Definition, or if Hopping Band is not available, proceed to Step 2.
PAGE 78
BreezeACCESS 4.0 Commissioning 1-8 ! Select Hopping Shift from the Basic Configuration menu. The Hopping Shift configuration screen appears. Select the required hopping shift value. Configuring VLAN Parameters 1. From the Basic Configuration menu, select VLAN Support. The VLAN Support menu appears. 2. From the VLAN Support menu, select VLAN Link Type. The VLAN Link Type configuration screen appears. Select the required option: Hybrid, Access or Trunk Link. 3.
PAGE 79
Setting Basic Parameters 1-9 ! Define at least one of the four WEP Keys by selecting one of them from the Security Parameters menu and entering the required key. ! Select Default Key ID from the Security Parameters menu and enter the number of a defined WEP key. ! Select Authentication Algorithm from the Security Parameters menu. The Authentication Algorithm menu opens. Select Shared Key.
PAGE 80
BreezeACCESS 4.0 Commissioning 1-10 Configuring Parameters in GU-A-BS Units Introduction This section describes all the parameters that are necessary for the initial installation and operation of GU-RA units. Once the unit is properly installed and operational, other parameters can be configured using the monitor program via Telnet or SNMP management. NOTE: The GU-RA does not have an external MON port, and therefore must be configured using Telnet.
PAGE 81
Setting Basic Parameters 1-11 Configuring Hopping Parameters 1. From the Basic Configuration menu, select Hopping Parameters. The Hopping Parameters menu opens. 2. From the Hopping Parameters menu, select Number of Hopping Frequencies. The Number of Hopping Frequencies configuration screen appears. Enter the number of hopping frequencies used by the system.
PAGE 82
1-12 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 83
Chapter 2 Optimizing the Wireless Link About This Chapter This chapter explains how to optimize the performance of the wireless link of BreezeACCESS Subscriber Units and includes the following sections: ! RSSI Measurement and Maximum Data Rate Configuration (Subscriber Units)‚ page 2-2, explains how to read the RSSI measurement and to configure the optimum value for the Maximum Data Rate parameter.
PAGE 84
BreezeACCESS 4.0 Commissioning 2-2 RSSI Measurement and Maximum Data Rate Configuration (Subscriber Units) The Continuous Link Quality Display test allows a continuously updated display of the average Received Signal Strength Indication (RSSI). As the test measures only the desired signal of properly received frames, it is a good indication of the quality of the received signal.
PAGE 85
Optimizing the Wireless Link 2-3 Aligning the Antenna of the SU-A/E Subscriber Unit NOTE: Antenna alignment using the RSSI bar display is possible only after the Access Unit you wish to associate with is operational and the basic parameters in the Subscriber Unit were properly configured. Otherwise, the unit will not be able to synchronize and associate with the Access Unit.
PAGE 86
2-4 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 87
Chapter 3 Connecting External Alarm Devices About This Chapter This chapter explains how to connect external devices to the AL IN and AL OUT connectors of the Base Station unit.
PAGE 88
BreezeACCESS 4.0 Commissioning 3-2 Connecting External Devices to the GU-BS AL IN and/or AL OUT Connectors Open-ended cables are available from the company for connecting to the module external alarm inputs through the AL IN connector and/or activating external devices through the AL OUT connector. See the tables that follow for descriptions of the connectors’ pins functionality. For details on defining and using the alarm inputs and output, refer to Book 4: Operation and Administration.
PAGE 89
External Devices 3-3 Alarms Out Cable 9-pin Micro D-Type AL OUT Connector Description Color Code 1 Relay 1 Common Brown 2 Relay 1 Normally Closed White 3 Relay 2 Common Green 4 Relay 3 Common Red 5 Relay 3 Normally Closed Black 6 Relay 1 Normally Open Purple 7 Relay 2 Normally Closed Yellow 8 Relay 2 Normally Open Orange 9 Relay 3 Normally Open Blue The other side of the cable is supplied open-ended. BreezeACCESS 4.
PAGE 90
3-4 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 91
Chapter 4 Verifying Proper Operation About This Chapter This chapter explains how to confirm that the BreezeACCESS system is functioning properly and includes the following sections: ! Verifying Connectivity‚ page 4-2, explains how to ensure that your BreezeACCESS and the equipment connected to them are operating properly. ! LED Indicators‚ page 4-4, lists the LEDs found on BreezeACCESS units and their meanings.
PAGE 92
BreezeACCESS 4.0 Commissioning 4-2 Verifying Connectivity Verifying the Ethernet Connection Once you have connected the unit to an Ethernet outlet, verify that the Ethernet Integrity indicator (the yellow LED embedded in the Ethernet connector) is on, indicating that the unit is connected to an Ethernet segment. The Ethernet Activity indicator (the green embedded LED) should blink whenever the unit receives or transmits traffic on the Ethernet port.
PAGE 93
Verifying Proper Operation 4-3 Verifying Proper Operation of the GU-RA GPS Antenna NOTE: It may take up to 10 minutes from the time the GU-RA GPS antenna is powered up until it is fully synchronized with the GPS satellite system. When the unit is operating properly, the PWR and OK green LEDS should be on, indicating that the unit is supplying power to the GPS antenna and that the GPS antenna is functioning properly. If the OK LED is not on, check the functionality of the GPS antenna as follows: 1.
PAGE 94
BreezeACCESS 4.
PAGE 95
Verifying Proper Operation 4-5 SU-NI and AU-NI Indoor Units LEDs Name Description Functionality PWR Power supply On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
PAGE 96
BreezeACCESS 4.0 Commissioning 4-6 BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
PAGE 97
BreezeACCESS V System Manual Book 4: Operations and Administration
PAGE 98
PAGE 99
Operations and Administration Table of Contents Accessing the Monitor Program ......................................................1-1 Accessing the Monitor Program using the RS 232 MON Connector ............................................................1-2 Accessing the Monitor Program using Telnet ........................1-4 Operating the Monitor Program ...............................................1-6 Menus and Parameters .......................................................2-1 Main Menu ........
PAGE 100
ii BreezeACCESS 4.0 Operations and Administration Security Parameters (AU and SU) ................................... 2-62 Voice Parameters (Subscriber Units with Voice Support Only) .................... 2-63 Dialing Parameters (Subscriber Units with Voice Support Only) .................... 2-64 Telephony Signals (Subscriber Units with Voice Support Only) ..................... 2-71 Hopping Parameters (GU) ............................................... 2-77 Alarm Parameters (GU) ..........................
PAGE 101
Chapter 1 Accessing the Monitor Program About This Chapter This chapter explains how to access the monitor program. It also describes how to use the monitor program to set up, configure, and manage BreezeACCESS Broadband Wireless Access system units. This includes the Subscriber Units (SUs), Access Units (AUs) and GPS and Alarms modules (GUs).
PAGE 102
BreezeACCESS 4.0 Operations and Administration 1-2 Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. NOTE: The GU-BS GPS and Alarms module does not have an external MON port. It does have an internal MON port that can be used in laboratory conditions (consult Alvarion technical support for further details).
PAGE 103
Accessing the Monitor Program 1-3 Table 1-1: Default Passwords Access Rights Password Read Only public Installer user Administrator private NOTE: Following three unsuccessful login attempts (using incorrect passwords) from either the monitor port or via Telnet, the monitor program will be blocked for five minutes. To enable access to the monitor program during that time, the unit must be reset (via SNMP or by disconnecting/reconnecting power). BreezeACCESS 4.
PAGE 104
BreezeACCESS 4.0 Operations and Administration 1-4 Accessing the Monitor Program using Telnet 1. Connect a PC to the Ethernet port of the unit. See the table below to determine the type of cable. Configure the PC’s IP parameters to enable connectivity with the unit (the default IP Address is 10.0.0.1). Run the Telnet application.
PAGE 105
Accessing the Monitor Program 1-5 ! For users with Read Only access rights, only the Info Screens option is displayed. Users with this access level cannot access the Unit Control, Basic Configuration, Site Survey and Advanced Configuration menus. ! For users with Installer access rights, the first four menu items (Info Screens, Unit Control, Basic Configuration and Site Survey) are displayed. Users with this access level cannot access the Advanced Configuration menu.
PAGE 106
BreezeACCESS 4.0 Operations and Administration 1-6 Operating the Monitor Program 1. Type an option number to open/activate the option. You may need to press Enter in some cases. 2. Press Esc to exit a menu or option. 3. You can log-out and exit the monitor program from the Main Menu by selecting X (exit). To get to the Main Menu from anywhere in the program, press the Esc key several times. You can also exit the monitor from anywhere in the program by simultaneously pressing the Ctrl and X keys.
PAGE 107
Chapter 2 Menus and Parameters About This Chapter This chapter describes the BreezeACCESS configuration menus and parameters. It includes the following sections: ! Main Menu‚ page 2-2. ! Info Screens Menu‚ page 2-3. ! Unit Control Menu‚ page 2-6. ! Basic Configuration Menu‚ page 2-10. ! Site Survey Menu‚ page 2-12. ! Advanced Configuration Menu‚ page 2-21.
PAGE 108
BreezeACCESS 4.0 Operations and Administration 2-2 Main Menu From the Main Menu you can access the following menus, depending on your access level: ! Info Screens – Provides read-only display of current parameter values. Available at all access levels. ! Unit Control – Enables access to general operations such as resetting the unit, loading the default parameters, changing passwords and switching between software versions. Available at the Installer and Administrator access levels.
PAGE 109
Menus and Parameters 2-3 Info Screens Menu BreezeACCESS/AU-BS Official Release Version – 4.0.40 Release Date: Thu Dec 20 21:05:08 2001 Info Screens ==================== 1 – Show Unit Status 2 – Show Basic Parameters 3 – Show Advanced Parameters S – Show All Parameters >>> Figure 2-1: Info Screens Menu The Info Screens menu enables viewing of the current values of various parameter sets. The parameter sets are identical to the main parameter groups in the configuration menus.
PAGE 110
BreezeACCESS 4.0 Operations and Administration 2-4 ! Console Speed – Displays the speed defined in the unit for the connected terminal, used for running the terminal emulation program. ! Number of Associations Since Last Reset – In SUs displays the total number of associations with any AU since the last reset, including duplicate associations with the same AU. In AUs, displays the number of SUs that have associated with the AU since the last reset, including duplicate associations with the same SU.
PAGE 111
Menus and Parameters 2-5 antenna. If the antenna is functioning and properly connected to the module, this may be because the antenna has not yet synchronized with the GPS satellite system. Show Basic Parameters The Show Basic Parameters menu displays the current values of the parameters included in the Basic Configuration menu (see Basic Configuration Menu‚ page 2-10). When using Read-Only access rights the ESSID and WEP Keys are not displayed.
PAGE 112
BreezeACCESS 4.0 Operations and Administration 2-6 Unit Control Menu The Unit Control menu includes the following options: ! Reset Unit – Resets the BreezeACCESS unit and applies any changes made to the system parameters. ! Defaults Settings – Resets the unit to a predefined set of default parameters or to save the current configuration as Operator Defaults. The available options are: " Set Defaults – Resets the unit to a set of default parameters.
PAGE 113
Menus and Parameters 2-7 community string. The procedure is the same as for downloading/uploading configuration files, except that the extension used for the file name is .cmr. Examples (using the default SNMP Write community string): To upload the configuration file using DOS based TFTP Client to an SU whose IP address is 206.25.63.65: tftp 206.25.63.65 put Suconf private.cmr. To download the configuration file from the same unit: tftp 206.25.63.65 get private.
PAGE 114
BreezeACCESS 4.0 Operations and Administration 2-8 ! Flash Memory Control – Selects the active software version. The following options are available: " Reset and Boot from Shadow Version – Activates the Shadow (backup) software version. The unit resets automatically and loads the shadow firmware. " Use Current Version After Reset – Defines the current version as the one that will be activated and used after the next reset. The flash memory can store two software versions.
PAGE 115
Menus and Parameters 2-9 The Event Log Menu includes the following options: " Event Log Policy – Determines the minimal severity level. All events whose severity is equal to or higher than the defined severity are logged. Valid values are: Log All (TRC) Level, Message (MSG) Level, Warning (WRN) Level, Error (ERR) Level, Fatal (FTL) Level, Log None. The default selection is Fatal (FTL) Level.
PAGE 116
BreezeACCESS 4.0 Operations and Administration 2-10 Basic Configuration Menu The Basic Configuration menu includes all the parameters that are necessary for the initial installation and operation of the unit. Once the unit is properly installed and operational, other parameters can be configured either locally using the monitor program or remotely using Telnet, SNMP management or TFTP for loading to the unit a pre-prepared configuration file.
PAGE 117
Menus and Parameters 2-11 ! VLAN ID – Voice & Management (SU with voice support) (see page 245) ! VLAN Link Type (see page 2-46) Security Parameters ! Authentication Algorithm (see page 2-62) ! Default Key ID (see page 2-62) ! WEP Key # 1 (see page 2-62) ! WEP Key # 2 (see page 2-62) ! WEP Key # 3 (see page 2-62) ! WEP Key # 4 (see page 2-62) NOTE: All parameters in the Basic Configuration menu are also available in the appropriate submenus of the Advanced Configuration menu. BreezeACCESS 4.
PAGE 118
BreezeACCESS 4.0 Operations and Administration 2-12 Site Survey Menu The Site Survey menu provides various tests and counters for verifying the quality of the wireless link and the proper operation of the unit. These tests can be used to help determine where to position the units for optimal coverage, to align antennas and to assist in troubleshooting. Traffic Statistics (AU and SU) The traffic statistics can be used to monitor, interpret and analyze the wired and wireless links performance.
PAGE 119
Menus and Parameters 2-13 Wireless Link Counters The unit transmits data frames received from the Ethernet port, as well as self-generated control and wireless management frames, to the wireless media. After transmission of a data frame, the unit waits for an acknowledgement (ACK) message from the receiving unit. Some control and wireless management frames as well as broadcast and multicast frames that are sent to more than one unit are not acknowledged.
PAGE 120
BreezeACCESS 4.0 Operations and Administration 2-14 where the ACSE Option in the AU is enabled. In this case the Voice count should be 0. ! Total retransmitted frames – Displays the total number of retransmissions of frames (counts all unsuccessful transmissions/ retransmissions). If the ACSE Option is enabled, then in addition to the total count, there are also separate counters for total number of Data frames and Voice (RTP) frames.
PAGE 121
Menus and Parameters 2-15 ! Duplicate frames discarded – Displays the number of frames discarded due to receiving multiple copies. If an acknowledge message was not received by the originating unit, the same data frame can be properly received twice (or more). Although duplicate frames are included in all counters that count data frames, only the first copy is forwarded to the Ethernet port.
PAGE 122
BreezeACCESS 4.0 Operations and Administration 2-16 Num The number of the information row, assigned automatically and sequentially by the program. Freq The hopping frequency, according to the hopping sequence. Rx The accumulated number of frames received at the specified frequency since last reset. Tx The accumulated number of frames transmitted successfully at the specified frequency since last reset.
PAGE 123
Menus and Parameters 2-17 ! Start Sending – Starts transmission of ping frames. ! Stop Sending – Stops the transmission of ping frames. The test will end automatically once the number of pings that were sent have reached the value specified in the No. of Pings parameter (described above). The Stop Sending option can be used to end the test before completing the specified number of pings, or if continuous pinging was selected.
PAGE 124
BreezeACCESS 4.0 Operations and Administration 2-18 " St (Static): An associated SU. These entries also include the SW Version of the SU. " Sp (Special): 5 Addresses that always exist: # The MAC address of the AU (appears twice as it is learned from both the Ethernet and the wireless ports) # Alvarion’s Multicast address (01:20:D6:00:00:01, also twice). The system handles this address as a Broadcast address.
PAGE 125
Menus and Parameters 2-19 # Authenticated # Not Authenticated (a temporary status) " The SW version of the SU.
PAGE 126
BreezeACCESS 4.0 Operations and Administration 2-20 AU the information is provided for each of the associated SUs, identified by their MAC address. The counters in the AU are reset when there is a new association with an SU (including reassociations). RSSI Display Option (AU and SU) In BreezeACCESS units running SW versions 3.X and below, all measurements of received RF signal levels are displayed using arbitrary RSSI units. From version 4.0 onward, the conventional dBm measurement units can be used.
PAGE 127
Menus and Parameters 2-21 Advanced Configuration Menu The Advanced Configuration menu provides access to all the parameters, including the parameters that are available through the Basic Configuration menu.
PAGE 128
BreezeACCESS 4.0 Operations and Administration 2-22 ! DHCP Client " DHCP Options – Displays the current status of the DHCP (Dynamic Host Configuration Protocol) support, and allows selecting a new operation mode. The available options are: # Disable – Use manual procedure for configuring the IP parameters. # DHCP Only – Search for a DHCP Server and obtain the IP parameters from it (IP Address, Subnet Mask and Default Gateway Address).
PAGE 129
Menus and Parameters 2-23 c. Define a different hopping sequence for each AU in order to minimize interference between adjacent AUs. NOTE: The same method for generating the basic hopping sequence (and the hopping shift mechanism) should be used for all units in the system to enable SUs to communicate with the AUs and to support radio planning that will provide minimal interference between neighboring sectors. ! Hopping Band – Available in units with INT option only.
PAGE 130
BreezeACCESS 4.
PAGE 131
Menus and Parameters 2-25 The default sequence (including the case where all frequencies were deleted) is the single lowest available frequency – 5725 MHz. " Add Frequencies – Adds discrete hopping frequencies or frequency ranges. Enter a list of frequencies and/or frequency ranges to be added, e.g. 5725-5735, 5740, 5744. Use a comma to separate between entries (no spaces). The allowed entries are from 5725 to 5875 in steps of 1 MHz. " Remove Frequencies - Removes frequencies from the existing list.
PAGE 132
BreezeACCESS 4.0 Operations and Administration 2-26 parameter (see below) must be configured in the AU. The Enhanced Mode is not suitable for sequences with 6 or less frequencies. If Enhanced Scrambling is selected with sequences that have 6 or less frequencies, than Standard Scrambling is used by default. The scrambled sequence is generated according to the following rules: a.
PAGE 133
Menus and Parameters 2-27 # Spanning Factor (AU only) – Defines the Spanning Factor to be used by the Enhanced Scrambling mechanism. The Spanning Factor should be chosen so that the GCD (Greater Common Divisor) of the Spanning Factor and the Number of Hopping Frequencies would be 1 (e.g. for 8 frequencies possible values for the Spanning Factor are 1, 3, 5 and 7). The SU learns the value of the Spanning Factor from the AU during the association process.
PAGE 134
BreezeACCESS 4.0 Operations and Administration 2-28 ! Hopping Shift –Displays the current Hopping Shift parameter and allows entry of a new value. Available only in AUs. All the associated SUs learn the value of the Hopping Shift parameter from the AU during the association process.
PAGE 135
Menus and Parameters 2-29 Table 2-3: ISM Hopping Sequence, Hopping Shift=3 Index Channel # Frequency (MHz) Index Channel # Frequency (MHz) Index Channel # Frequency (MHz) 1 5 5730 28 8 5733 55 18 5743 2 28 5753 29 42 5767 56 38 5763 3 67 5792 30 15 5740 57 70 5795 4 13 5738 31 39 5764 58 55 5780 5 48 5773 32 71 5796 59 61 5786 6 21 5746 33 12 5737 60 47 5772 7 76 5801 34 73 5798 61 53 5778 8 52 5777 35 80 5805 62 20 5745 9 2
PAGE 136
BreezeACCESS 4.0 Operations and Administration 2-30 (Index=N where N is the number of channels in the sequence) will result in the first channel (Index=1).
PAGE 137
Menus and Parameters 2-31 N=number of channels in the sequence (modulus) P0(j)=Channel no. j in the basic sequence (shift=0) PS(j)=Channel no. j in the actual sequence with hopping shift S Example: The basic hopping sequence is 1, 4, 7, 2, 5, 8, 3, 6 (Enhanced Scrambling, N=8, Spanning Factor=3).
PAGE 138
BreezeACCESS 4.
PAGE 139
Menus and Parameters 2-33 ! Hopping Sync (BS-AU only) –Displays the current Hopping Sync status of the unit and allows defining a new status. When several AUs that use the same hopping set and different hopping sequences are co-located, their operation should be synchronized in terms of hopping sequence initialization and timing. If a BS-GU GPS module is not used for synchronization, then one AU must be specified as a Master unit and all other units must be specified as Slave units.
PAGE 140
BreezeACCESS 4.0 Operations and Administration 2-34 Operator ESSID. The ESSID as well as the Operator ESSID are included in the AU’s Beacon & Probe Response management frames. The SU shall regard such frames if the ESSID or Operator ESSID matches its own ESSID. The ESSID of the AU with which the SU is associated is defined as the Run-Time ESSID, to be used by the SU when communicating with the AU.
PAGE 141
Menus and Parameters 2-35 The Best AU selection mechanism can be overridden by defining a specific AU as the preferred AU. NOTE: Although the SU selects the Best AU based on long-term conditions prior to the decision time, it may not always be connected to the instantaneous Best AU at any given time. Note also that the decision is done only once during the scanning interval. The decision may not remain the optimal one for ever.
PAGE 142
BreezeACCESS 4.0 Operations and Administration 2-36 Valid values: MAC address string The default value for the Preferred AU MAC Address is 00-00-00-00-00-00 (12 zeros), meaning that there is no preferred AU. " Show Best AU Parameters and Data – Displays the applicable information: # • • • • • Neighboring AU Data table - Displayed for each AU that the unit can communicate with the following parameters: MAC Address Received signal strength – RSSI or dBm Mark – The computed quality mark for the AU.
PAGE 143
Menus and Parameters 2-37 BreezeACCESS units operate at data rates of 3 Mbps, 2 Mbps, 1 Mbps. Under certain conditions (compatibility reasons or range/ speed trade-off), you may decide to limit the use of higher rates. If the quality of the link is not good enough, it is recommended to decrease the value of this parameter (the higher the data rate, the higher the error rate).
PAGE 144
BreezeACCESS 4.0 Operations and Administration 2-38 Table 2-8: Recommended Maximum Data Rate Maximum Data Rate 3Mbps 2Mbps 1Mbps SU-A/E RSSI>-67 dBm -75 dBm
PAGE 145
Menus and Parameters 2-39 The SU is deleted from the Call Information database once it sends a message that the call was terminated. Throughout the voice call, the SU periodically transmits keep-alive (re-association) messages approximatly every ten minutes indicating that the call is still on. If such messages are not received for a period defined by the Call Aging Time parameter, the following will take place. a.
PAGE 146
BreezeACCESS 4.0 Operations and Administration 2-40 ! ACSE Parameters – The ACSE (Adaptive Circuit Switched Emulation) Voice Scheduler is a proprietary enhanced air protocol that provides guaranteed delay and jitter properties for voice sessions by reserving specific time slots for each active telephone call. The ACSE Voice Scheduler allows the delivery of high quality voice, while maintaining the inherent efficiency of statistically multiplexed packet based networks.
PAGE 147
Menus and Parameters 2-41 Valid values are from 0 (no retransmissions) to 100. The default value is 6. " ACSE Number Of Retransmissions For Voice (AU and SU with voice support) – The maximum number of times that a voice packet that was not acknowledged will be retransmitted. When the ACSE Option is enabled, this parameter overrides the Number Of Retransmissions parameter. This parameter has no effect when the ACSE Option is disabled. Valid values are from 0 (no retransmissions) to 100.
PAGE 148
BreezeACCESS 4.0 Operations and Administration 2-42 " Disable – No IP address based filtering " Activate Management IP Filter On Ethernet Port – Applicable only if the Access to Network Management parameter is configured to either From Ethernet Only or From Both Ethernet & Wireless Link. The unit can be managed from the Ethernet port only by stations whose IP addresses match one of the entries in the Set Network Management IP Addresses list.
PAGE 149
Menus and Parameters 2-43 " Send SNMP Traps – Enables/disables sending of SNMP traps. Available options are: # Enable Traps Sending # Disable Traps Sending The default selection is Disable Traps Sending. " SNMP Traps IP Destination – Displays the current values of 3 IP addresses that are defined as the trap destinations. Allows entering a new address (4 groups of 3 digits each, separated by dots) for each of the 3 entries. The default of all three SNMP Traps IP Destinations is 000.000.000.000.
PAGE 150
BreezeACCESS 4.0 Operations and Administration 2-44 " VLAN ID-Data (SU unit only) – Applicable for Access links only. Sets the VLAN ID for data frames, identifying the VLAN to which the unit belongs. Valid values: 1 to 4094. Default value: 1. Frames received from the Wireless link port: • Only tagged frames with VLAN ID (VID) value equal to the VLAN ID Data defined in the unit are forwarded to the Ethernet port.
PAGE 151
Menus and Parameters 2-45 The following table summarizes the functionality of the internal management port in accordance with the value of the VLAN ID – Management parameter. The table is valid for all link types.
PAGE 152
BreezeACCESS 4.0 Operations and Administration 2-46 • If the Voice Priority Tag Option is enabled, a VLAN Priority Tag is inserted in all voice frames (RTP packets) generated by the unit before transmission to the Wireless or Ethernet port. The tag includes a VID value of zero and the VLAN Priority – Voice parameter. The following table summarizes the functionality of the internal management and voice ports in accordance with the value of the VLAN ID – Voice & Management parameter.
PAGE 153
Menus and Parameters 2-47 Table 2-11: VLAN Data Port Functionality Summary – Access Link Action Data Port (SU) Accept from Ethernet Untagged frames Accept from Wireless Tagged frames, matching VID-D Tag Insert VID-D, PID-D (to wireless) Tag Remove Yes (to Ethernet) Legend: VID-D: VLAN ID-Data PID-D: VLAN Priority-Data # Trunk Link – Transfers only tagged frames, because all devices connected to it are VLAN-aware: Only tagged data frames received on Ethernet or wireless link ports are forwarded.
PAGE 154
BreezeACCESS 4.0 Operations and Administration 2-48 Table 2-12: VLAN Data Port Functionality Summary – Trunk Link Action Data Port (SU and AU) Accept from Ethernet Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded. Accept from Wireless Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded.
PAGE 155
Menus and Parameters 2-49 Trunk Link and the VLAN Forwarding option is enabled, a received data frame with a VLAN ID that is not a member of the unit’s VLAN Forwarding List will be discarded. The VLAN Forwarding parameter provides the following options: # VLAN Forwarding Support – Enables or disables the VLAN Forwarding feature. Available selections are Disable and Enable. The default selection is Disable. # Add Forwarding VLAN ID – Adds a VLAN ID to the VLAN Forwarding List.
PAGE 156
BreezeACCESS 4.0 Operations and Administration 2-50 The maximum number of VLAN IDs in the VLAN Relaying List is 20. Valid values are 1 to 4094. # Remove Relaying VLAN ID – Removes a VLAN ID from the VLAN ID Relaying List. Valid values are VID values (from 1 to 4094) that are included in the VLAN Relaying List. # Show VLAN ID Relaying List – Displays the values of the VLAN IDs that are included in the VLAN Relaying List.
PAGE 157
Menus and Parameters 2-51 The VLAN Traffic Priority menu allows viewing and setting the following parameters: # VLAN Priority – Data (SU only) – Applicable for Access link only. Displays and sets the value of the VLAN Priority field for data frames that are transmitted to the wireless link. All data frames are routed to the Low queue. This parameter will only impact the way that other VLANaware devices will handle the packet. Valid values are 0-7. The default value is 0.
PAGE 158
BreezeACCESS 4.0 Operations and Administration 2-52 Since the system supports both Layer 2 and Layer 3 prioritization, a frame will be routed to the Mid queue if one of the following conditions is met: a. The precedence in the ToS field is higher than the value of the ToS Precedence Threshold parameter (applicable to both tagged and untagged frames). b. The VLAN Priority field in a tagged frame is higher than the value of the VLAN Priority Threshold parameter. Valid values are 0-7. The default value is 4.
PAGE 159
Menus and Parameters 2-53 Ethernet Broadcast Filtering (SU only) Allows defining the Layer 2 (Ethernet) broadcast and multicast filtering capability. The Ethernet Broadcast Filtering allows enhancing the security of the system and saving bandwidth on the wireless media through blocking protocols that are typically used in the customer’s LAN but are not relevant for other customers (e.g. NetBios that is used by Microsoft Network Neighborhood).
PAGE 160
BreezeACCESS 4.0 Operations and Administration 2-54 " Disable– PPPoE Broadcast messages is filtered or transmitted according to the general filtering criteria set by the selected value of the Filter Options parameter. " Enable– PPPoE Broadcast messages is transmitted regardless of the selected value of the Filter Options parameter. The default selection is Disable.
PAGE 161
Menus and Parameters 2-55 wired LAN and are not sent back to the wireless link. Disable Broadcast Relaying if you are sure that all broadcast messages from the wireless link will be destined to the wired LAN. The default selection is Enable. ! Unicast Relaying (AU only) – Determines whether the unit performs Unicast relaying. When Unicast Relaying is enabled, Unicast packets originating in devices on the wireless link can be transmitted back to the wireless link devices.
PAGE 162
BreezeACCESS 4.0 Operations and Administration 2-56 NOTE: The Number of Dwells to Retransmit is not applicable to ACSE voice frames since voice is sensitive to delay. All ACSE voice frames will be retransmitted within the same dwell, up to the maximum number of retransmissions allowed as defined by the ACSE Number Of Retransmissions For Voice parameter.
PAGE 163
Menus and Parameters 2-57 The default is the minimum possible rate, 1Mbps. ! Multi-Rate – Link quality dynamically changes, due to various environmental conditions. Dynamically switching between the possible transmission rates increases the probability of using the maximum rate for the current radio link quality at any given moment. Decreasing the rate one step improves the receiver sensitivity by 6-8dB. When enabled, the transmission rate decisions are made separately for each unit.
PAGE 164
BreezeACCESS 4.0 Operations and Administration 2-58 the value of this parameter will increase the probability that it will be a successful window, thus slowing down the decision to degrade to a lower rate and accelerating the decision to upgrade to a higher rate. Valid value: 1 to Multi-Rate Decision Window Size. Default value: 8. ! Dwell Time (AU only) – The time spent on a radio channel before hopping to the next channel according to the operational hopping sequence.
PAGE 165
Menus and Parameters 2-59 The default for all subnet masks is 255.255.255.255. " Set User Filter Range – Defines a range of addresses for each of the User Filter IP Address entries (the range includes the base address). Valid values: 0 – 255. The default value is 0 (not used). NOTES: You may use either Mask or Range (but not both) to define a group of user filter addresses.
PAGE 166
BreezeACCESS 4.0 Operations and Administration 2-60 period of inactivity. If no data was received from the Ethernet port during the last N seconds, the unit is allowed to transmit N times its CIR value without any delay. For example, after an inactivity time of 0.5 second, a unit with CIR = 64 Kbps can transmit up to 64 Kbits x 0.5 = 32 Kbits without any delay. " MIR/CIR Option – Enables or disables the CIR/MIR support feature. In cells where the AU and all SUs use SW version 4.
PAGE 167
Menus and Parameters 2-61 Valid values: 0 – 2000 (milliseconds). Default value: 5 (milliseconds), allowing a maximum burst of (0.005 X CIR) Kbps, after an inactivity period of 5 milliseconds or more. " Maximum Delay (SU only) – Sets the maximum permitted delay in the buffers system. Some applications are very sensitive to delay. If relatively high delays are permitted, such applications may suffer from poor performance due to accumulation in the buffers of data from other applications (e.g. FTP).
PAGE 168
BreezeACCESS 4.0 Operations and Administration 2-62 the Run-Time MIR/CIR Option, which is the actual status of the option (may be different from the MIR/CIR Option selected in the SU because it is controlled by the AU). ! Show Service Parameters – Displays the current values of the Service Parameters. Security Parameters (AU and SU) Unauthorized wireless connection is prevented by using the Wired Equivalent Privacy (WEP) algorithm defined in the IEEE 802.11 Wireless LAN standard.
PAGE 169
Menus and Parameters 2-63 configured before the Shared Key authentication mode can be used. The Subscriber Unit must use the same WEP Key that is used by the Access Unit. The WEP Key is a string of 10 hexadecimal numbers. The default for all 4 keys is a string of 10 zeros (no key). NOTE: It is recommended to change the WEP Keys periodically, to enhance system security.
PAGE 170
BreezeACCESS 4.0 Operations and Administration 2-64 value of the Frames per Packet parameter, the higher are the delay introduced (reduced quality) and the higher is the number of simultaneous voice sessions that can be supported by the AU. There is a separate setting for each of the voice codecs that are supported by the unit. The allowed range differs among codecs, in accordance with the different packet sizes (30 ms for G723.1, 10 ms for G729 and 5 ms for G711).
PAGE 171
Menus and Parameters 2-65 ! Pulse Dialing – Enables or disables the automatic pulse dialing detection feature to support telephones with pulse dialing. The default selection is Enable. ! Gatekeeper Option – If set to Enable, the unit will communicate with the Gatekeeper to resolve the destination telephone number into the IP address and to register its own phone number and IP address with the Gatekeeper. The default selection is Disable.
PAGE 172
BreezeACCESS 4.0 Operations and Administration 2-66 ! IP Dialing Option – Enables or disables dialing using IP addresses. The default selection is Enable. ! IP Dialing Indicator – Specifys the prefix used to identify an IP Dialing string. Applicable only if the IP Dialing Option parameter (see above) is set to Enable. Digits dialed after IP Dialing Prefix are assumed to be the destination IP address. 12- and 3-digit numbers are allowed.
PAGE 173
Menus and Parameters 2-67 " Unrestricted with tones (used by H.323 AudioVisual terminals for transmission of unrestricted digital information with tones/announcement) " Video (not used by H.323 terminals) The default is Speech. NOTE: This information element is encoded according to Figure 4-11/Q.931 and Table 4-6/ Q.931. The SU support only H323 Speech traffic and a change of the default value is not recommended. A change will be needed only as result of special PSTN switch requirements.
PAGE 174
BreezeACCESS 4.0 Operations and Administration 2-68 Default value: 0. " International Prefix – Defines the second digit in the two digits string indicating an international call. Valid values: One phone key-pad digit (0-9, *, #, A, B, C, D) and X (no prefix). Default value: 0. ! Registration TTL – Defines the registration Time To Live. Registration is the process by which an endpoint informs the Gatekeeper of its Transport Addresses and alias addresses.
PAGE 175
Menus and Parameters 2-69 The default selection is Enable. ! Endpoint Type – Defines the EndpointType components in H.323 messages for interoperability with other equipment using H.323. Available options are Terminal, Gateway. The default is Terminal ! Fax Relay – Defines the use of T.38 protocol for relaying fax messages. T.38 is a protocol dedicated to fax. In the T.
PAGE 176
BreezeACCESS 4.0 Operations and Administration 2-70 " Forward -> Reverse Battery – Change the polarity from forward to reverse " Reverse -> Forward Battery – Change the polarity from reverse to forward The default is Forward Battery. ! Caller ID: Defines whether the unit will support generation of Caller ID (CID) signaling and if CID generation is supported, which standard will be used.
PAGE 177
Menus and Parameters 2-71 " Disable: The # sign is interpreted as a part of the dialed sequence. End of dialing is determined by the Stop Dialing Timeout parameter. " Enable: The # sign is interpreted as indicating end of dialing sequence. Telephony Signals (Subscriber Units with Voice Support Only) The Telephony Signals menu defines the various call progress tones that indicate the status of a telephone call, the ringer parameters and some timeouts.
PAGE 178
BreezeACCESS 4.0 Operations and Administration 2-72 any reason the call was disconnected because of a problem in the wireless link or incompatible capabilities) or if the user did not hang up after exceeding the specified duration of the Dial, Ring Back, Busy or Congestion Tones. ! High Level Error Tone – Defines the high level tone transmitted to the earphone to better attract the attention of the user if he did not hang up after exceeding the specified duration of the Error Tone.
PAGE 179
Menus and Parameters 2-73 " Cadence Off – The silence time (on) in the ringing-silence sequence of the Ringer. Valid values are 100 – 10,000 milliseconds. " Duration - The maximum duration of activating the ringer. Ringing will cease upon detecting off-hook condition. Valid values are 0 – 10,000 seconds. ! Timeouts – Defines the following timeouts: " Min. Flash Detect Timeout and Max.
PAGE 180
BreezeACCESS 4.
PAGE 181
Menus and Parameters 2-75 Table 2-16: Parameters of Call Progress Tones and Ringer - Sweden Frequency 1 Frequency 2 Cadence Duration (s) Tone Freq (Hz) Level (dB) Freq (Hz) Level (dB) On (ms) Off (ms) Dial Tone 425 -18 0 0 Ring Back 425 -18 0 0 1000 5000 60 Busy 425 -18 0 0 250 250 15 Congestion 425 -18 0 0 250 750 0 Error 425 -18 0 0 200 200 0 High Level Error 0 0 0 0 0 0 0 Ring Frequency 25 1000 5000 60 15 Table 2-17: Parameters of Call Progre
PAGE 182
BreezeACCESS 4.
PAGE 183
Menus and Parameters 2-77 Table 2-20: Parameters of Call Progress Tones and Ringer – Chile Frequency 1 Frequency 2 Cadence Duration (s) Tone Freq (Hz) Level (dB) Freq (Hz) Level (dB) On (ms) Off (ms) Dial Tone 400 -6 0 0 Ring Back 400 -6 0 0 1000 3000 120 Busy 400 -6 0 0 500 500 20 Congestion 400 -6 0 0 200 200 20 Error 400 -6 0 0 500 500 20 High Level Error 400 3 0 0 500 500 20 Ringer 20 1000 3000 120 20 Table 2-21: Timeouts Country Min.
PAGE 184
BreezeACCESS 4.0 Operations and Administration 2-78 If the ISM hopping sequence is used (ISM US FCC or ISM International), the number of hopping frequencies is 79. ! Dwell Time – Applicable only when the ACSE Option is disabled. When the ACSE Option is enabled this parameter is not applicable and the dwell time is the ACSE Dwell Time, set to a fixed value of 60 milliseconds (see page 2-58).
PAGE 185
Menus and Parameters 2-79 the chassis. Alarm In 5 (GPS Antenna Status) is generated internally in the GU module, and it is turned on to indicate that proper PPS (pulse per second) timing signals are received from the GPS antenna. NOTES: Over Temperature alarm indication is only supported by the AC power supply module.
PAGE 186
BreezeACCESS 4.0 Operations and Administration 2-80 ! 2 – Activate if Alarm In 2 turns ON. ! 3 – Activate if Alarm In 3 turns ON. ! 4 – Activate if Alarm In 4 turns ON.
PAGE 187
Menus and Parameters 2-81 " Alarm In 7: PS1 Over Temperature (over temperature indication for BS-PS Power Supply module 1, which is the module inserted in the left-most slot of the chassis). " Alarm In 8: PS2 Over Temperature (over temperature indication for BS-PS Power Supply module 2, which is the module inserted in the right-most slot of the chassis). " Alarm In 9: PS1 Power (power fail indication for BS-PS Power Supply module 1, which is the module inserted in the leftmost slot of the chassis).
PAGE 188
2-82 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 189
Chapter 3 Configuration Download/Upload About This Chapter This chapter describes the method of configuring a large number of BreezeACCESS units at once.
PAGE 190
BreezeACCESS 4.0 Operations and Administration 3-2 The Configuration Download/Upload feature in BreezeACCESS units simplifies the task of remotely configuring a large number of units using TFTP protocol. By downloading the configuration file to a PC it is possible to view all the parameters configured at the unit, as it is a plain text ASCII file.
PAGE 191
BreezeACCESS V System Manual: Appendices
PAGE 192
PAGE 193
Appendix A: Software Version Loading Procedure General Firmware upgrades to the unit's FLASH memory are performed by a simple loading procedure using a TFTP application. Before performing an upgrade procedure, be sure you have the correct files and latest instructions. NOTE: Shutting down power to the unit before completion of the loading procedure may cause the unit to be inoperable. Verify that you have IP connectivity to the unit to be loaded with a new version.
PAGE 194
BreezeACCESS 4.0 System Manual A-2 6. To verify the connection, ping the unit’s IP address. Verify that ping replies are being received. The procedure to be used depends on the unit’s FLASH memory type. Identify the FLASH memory type by using the monitor program, connecting the PC to the unit either directly or via Telnet. From the Main Menu, select 1 – Info Screens. From the Info Screen menu select 1 – Show Unit Status.
PAGE 195
Appendix A A-3 Loading an Upgrade to a Unit with FLASH Type: F Use the following table to determine which source file name to use, according to the unit’s type. Unit Type Source File Name AU AXF.BS SU AXF.SU SU with Voice AXF.SUV GU AXF.GU X, refers to the software version number, up to 5 decimal digits (e.g. for software release 4.0.40, X=4040). Use the SNMP write community .dwn (the default write community is private) to define the destination filename.
PAGE 196
BreezeACCESS 4.0 System Manual A-4 3. From the Flash Memory Control menu, select S – Show Flash Versions. The display appears as follows: Flash Versions =========== Current Version: 3.0.39 Shadow Version: 4.0.40 Version After Reset:3.0.39 From the Flash Memory Control menu select the active software version, using the following procedures: To activate the backup (shadow) version: 1. From the Flash Memory Control menu select 1 - Reset and Boot from Shadow Version.
PAGE 197
Appendix A A-5 Loading an Upgrade to a Unit with FLASH Type: S Use the following table to determine which source file name to use, according to the unit’s type. Unit Type File Name AU AXS.BS SU AXS.SU SU with Voice AXS.SUV GU AXS.GU X refers to the software version number, up to 5 decimal digits (e.g. for software release 4.0.40, X=4040). Use the SNMP write community .fmr (default write community is private) to define the destination filename.
PAGE 198
BreezeACCESS 4.0 System Manual A-6 3. From the Flash Memory Control menu, select S – Show Flash Versions. The display appears as follows: Flash Versions =========== Current Version: 3.0.39 Shadow Version: 4.0.40 Version After Reset:3.0.39 From the Flash Memory Control menu select the active software version, using the following procedures: To activate the backup (shadow) version: 1. From the Flash Memory Control menu select 1 - Reset and Boot from Shadow Version.
PAGE 199
Appendix B: Supported MIBs and Traps BreezeACCESS agents support the following MIBs: ! MIB-II (RFC1213) ! BRIDGE-MIB (RFC1286) ! BreezeCOM brzAccessMib ! BreezeCOM brzPhoneMib ! BreezeCOM brznetmib
PAGE 200
BreezeACCESS 4.0 System Manual B-2 BreezeACCESS System Object Identifiers Path: breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomNewOID {breezecom 10} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10 breezecomBreezeACCESSproducts {breezecomNewOID 2} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10.2 breezecomBreezeACCESS_ACCESS {breezecomBreezeACCESSproducts 1} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10.2.
PAGE 201
Appendix B B-3 breezecomSU_R_1D1V breezecomBreezeACCESS_ACCESS 18 (710.10.2.1.18) SU-R-BD1V breezecomAU_NI breezecomBreezeACCESS_ACCESS 19 (710.10.2.1.19) AU-NI breezecomAU_BS breezecomBreezeACCESS_ACCESS 20 (710.10.2.1.20) AU-BS breezecomAU_I breezecomBreezeACCESS_ACCESS 21 (710.10.2.1.21) AU-I breezecomSU_BS breezecomBreezeACCESS_ACCESS 22 (710.10.2.1.22) SU-BS breezecomAU_BS_WA breezecomBreezeACCESS_ACCESS 23 (710.10.2.1.
PAGE 202
BreezeACCESS 4.0 System Manual B-4 brzAccessMIB Path: breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomPrvRev {breezecom 3} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3 brzAccessMib {breezecomPrvRev 3} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3.3 Note: * is used instead of the brzacc prefix Service Parameters MIB Parameter (Location in Parenthesis) Description *ServiceParameters 710.3.3.1 (brzAccessMib 1) MIR/CIR Parameters.
PAGE 203
Appendix B B-5 *MirOnlyOption 710.3.3.1.10 (*ServiceParameters 10) Applicable only to AU when CIR/MIR option is enabled. When enabled, the MIR/CIR algorithm fo determining the actual information rate is overridden and operates only with the configured MIR values. The graceful degradation algorithm is disabled. disable (0) enable (1) na (255) User Filtering Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *UserFilterParams 710.3.3. 2 (brzAccessMib 2) Applicable to SU only.
PAGE 204
BreezeACCESS 4.0 System Manual B-6 Network Management Parameters MIB Parameter (Location in Parenthesis) Description *NwMngParameters 710.3.3. 4 (brzAccessMib 4) Network Management parameters. *AccessToNwMng 710.3.3. 4.1 (*NwMngParameters 1) Applicable to AU and SU. The port to be used for remote management. wlanOnly: Management E from Wireless port only. ethOnly: Management enabled from Ethernet port only. bothWlanEth: Management enabled from both Wireless and Ethernet ports.
PAGE 205
Appendix B B-7 *NwMngTrapTableIdx 710.3.3. 4.7.1.3 (mngTrapEntry 3) Applicable to AU, SU and GU. Read only. Tables Index for an entry in the Management Trap Table. Integer 1-3 *DeleteOneTrapAddr 710.3.3. 4.8 (*NwMngParameters 8) Applicable to AU, SU and GU. Deletes a single selected entry from the Management Trap Table. Integer off (0) firstEntry (1) secondEntry (2) thirdEntry (3) na (255) *DeleteAllTrapAddrs 710.3.3. 4.7.9 (*NwMngParameters 9) Applicable to AU, SU and GU.
PAGE 206
BreezeACCESS 4.0 System Manual B-8 Bridge Parameters MIB Parameter (Location in Parenthesis) Description *BridgeParameters 710.3.3. 5 (brzAccessMib.5) Bridge parameters. *EthBroadcastFiltering 710.3.3. 5.1 (*BridgeParameters 1) Applicable to SU only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable: No filtering. ethOnly: Filter broadcasts received on the Ethernet port only. wlanOnly: Filter broadcasts received on the Wlan port only.
PAGE 207
Appendix B B-9 *VlanRelayingSupport 710.3.3. 5.2.8.1 (*VLANRelaying 1) Applicable to AU only. Enables or disables VLAN Relaying. (applicable in Trunk links only) Integer disable (0) enable (1) na (255) *VlanRelayingTable 710.3.3. 5.2.8.2 (*VLANRelaying 2) Applicable to AU only. A VLAN Relaying Table of up to 20 VLAN IDs of devices to which data frames are relayed when VLAN Relaying is Enabled. (applicable in Trunk links only). Not accessible. *VlanRelayingEntry 710.3.3. 5.2.8.2.
PAGE 208
BreezeACCESS 4.0 System Manual B-10 * ARPBroadcastOverrideFilter 710.3.3. 5.7.3 (*EthBroadcastingParameters 3) Applicable to SU only. Enables or disables the broadcasting of ARP messages, overriding the general *EthBroadcastFiltering Ethernet broadcast filtering option. Integer no (0) yes (1) na (255) *VoicePacketsToS 710.3.3. 5.8.1 (*ToSPriorityParameters 1) Applicable to SU with voice only. The Type of Service value to be inserted in the IP header of voice (RTP) packets.
PAGE 209
Appendix B B-11 Air Interface Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *ESSID 710.3.3. 6.1 (*AirInterface 1) Applicable to SU and AU. The Extended Service Set ID (ESSID) used to prevent the merging of collocated systems. Accessible only with SNMP Write Community. DisplayString (SIZE(31)) Up to 31 printable case sensitive ASCII characters. *AckDelayLimit 710.3.3. 6.2 (*AirInterface 2) Applicable to SU and AU.
PAGE 210
BreezeACCESS 4.0 System Manual B-12 *HoppingSync 710.3.3. 6.7 (*AirInterface 7) Applicable to BS-AU only. Inter-AU hopping sync functionality of the unit. In the BreezeACCESS II family, synchronization among AUs is not available with the following Country Standards: US FCC, Australia, Canada. In the BreezeACCESS V family, synchronization is not available if the selected hopping band is ISM US FCC. Integer idle (0) slave (1) master (2) na (255) *HoppingShift 710.3.3. 6.
PAGE 211
Appendix B *HoppingBands 710.3.3. 6.9 (*AirInterface 9) B-13 Applicable to SU and AU only. In BreezeACCESS II this is readonly, showing the Country Standard set in the factory. In BreezeACCESS MMDS it is read-only, showing Flexible Hopping Definition. In BreezeACCESS XL products that support only Flexible Hopping Definition for setting the hopping frequencies (e.g. 3.3a band), it is read-only, showing Flexible Hopping Definition.
PAGE 212
BreezeACCESS 4.0 System Manual B-14 *MaxDataRate 710.3.3. 6.10 (*AirInterface 10) Applicable to SU and AU. The maximum transmission data rate. Integer max1Mbps (1) max2Mbps (2) max3Mbps (3) na (255) *TransmitPowerControl 710.3.3. 6.11 (*AirInterface 11) Applicable to IF based units (AU-A/ E and SU-A/E) only. Enables reducing the transmit power level. The maximum available value is for maximum power. A lower value reduces the transmitted power.
PAGE 213
Appendix B B-15 *SubBandsTableIdx 710.3.3. 6.15.4.1.2 (*SubBandEntry 2) Applicable to SU and AU only. Read-only. A Sub-Band Table entry index. Integer *SubBandExp 710.3.3. 6.15.4.1.3 (*SubBandEntry 3) Applicable to SU and AU only. Read-only. A Sub-Band in the SubBands Table. DisplayString (SIZE(10)) *CurrentHoppingSeqTable 710.3.3. 6.15.5 (*FlexSubBandDef 5) Applicable to SU and AU only. The list of hopping frequencies in the Current Hopping Sequence. Not accessible. *CurrentHoppingSeqEntry 710.3.
PAGE 214
BreezeACCESS 4.0 System Manual B-16 *EraseManualSequence 710.3.3. 6.15.9.3 (*ScramblingDefinition 3) Applicable to SU and AU. Erase the manually configured sequence. Integer cancelOperation (0) eraseAll (1) *SpanningFactor 710.3.3. 6.15.9.4 (*ScramblingDefinition 4) Applicable to AU only. The Spanning Factor to be used by the Enhanced Scrambling mechanism. The Spanning Factor should be chosen so that the GCD (Greater Common Divisor) of the Spanning Factor and the Number of Frequencies would be 1 (e.g.
PAGE 215
Appendix B B-17 *CurrentTxPwrLvl 710.3.3. 6.18 (*AirInterface 18) Applicable to SU-R, SU-I and AU-I units only. Enables setting the transmitted power level according to the unit capabilities. The medium (2) value is not applicable to SU-I and AU-I and to some SU-R products. Integer Low (0) high (1) medium (2) *WirelessTrapThreshold 710.3.3. 6.19 (*AirInterface 19) A wireless link quality threshold for sending the *WirelessStatusTRAP,or *WirelessStatusOfSUsTRAP.
PAGE 216
BreezeACCESS 4.0 System Manual B-18 *NeighborAuDbm 710.3.3. 6.23.3.1.7 (*NeighborAuEntry 7) Applicable to SU only. Read-only. The received signal strength in dBm of an AU in the Neighbor AU Table. Integer *PreferredAuMacAddress 710.3.3. 6.23.5 (*BestAu 5) Applicable to SU only. The MAC address of the preferred AU (overriding the Best AU selection process. 00...00 (all zeros in address) means no preferred AU is set. MAC Address *TransmitLevel 710.3.3. 6.
PAGE 217
Appendix B B-19 *SPFreqs 710.3.3. 6.31.2 (* SiteProprietary 2) Site Proprietary frequencies parameters. *SPFreqsTable 710.3.3. 6.31.2.1 (*SPFreqs 1) A table of frequencies in the Site Proprietary hopping sets. Not accessible. sPFreqsEntry 710.3.3. 6.31.2.1.1 (*SPFreqsTable 1) An entry in the table of frequencies in the Site Proprietary hopping sets. Not accessible. sPFreqIdx 710.3.3. 6.31.2.1.1.1 (sPFreqsEntry 1) A index of an entry in the able of frequencies in the Site Proprietary hopping sets.
PAGE 218
BreezeACCESS 4.0 System Manual B-20 Performance Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *NumOfRetransmissions 710.3.3. 7.1 (*PerformanceParams 1) Applicable to SU and AU. Maximum times to retransmit an unacknowledged packet. Applicable only when the *ACSEOption is disabled. Integer 0-100 *NumOfDwellToRetransmit 710.3.3. 7.2 (*PerformanceParams 2) Applicable to SU and AU. Minimum dwell periods during which an unacknowledged packet is retransmitted.
PAGE 219
Appendix B *SyncSignalSource 710.3.3. 7.12.1 (*GpsHoppingParams 2) B-21 Applicable to GU Only. The source of the synchronization signal. When using a single GU, it should always be configured to 1 (gPSAntennaOrInternal). When using several daisy-chained units and a GPS Antenna is connected to the first unit, than all units should be configured to 1 (gPSAntennaOrInternal).
PAGE 220
BreezeACCESS 4.0 System Manual B-22 Site Survey Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *SiteSurvey 710.3.3. 8 (brzAccessMib 8) PerHopStatisticsTable 710.3.3. 8.1 (*SiteSurvey 1) Applicable to SU and AU. Statistics accumulated since last reset and average RSSI per frequency for all hopping frequencies in the (sequence). Not Accessible. hopSeqEntry 710.3.3. 8.1.1 (perHopStatisticsTable 1) Applicable to SU and AU. A Per Hop Statistics Table entry. Not accessible.
PAGE 221
Appendix B B-23 *TotalRxFramesFromWireless 710.3.3. 8.2.3.2 (*WlanCounters 2) Applicable to SU and AU. Read-only. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU. The count does not include frames that were discarded internally, bad frames and duplicate frames. Counter *TotalRetransmittedFragments 710.3.3. 8.2.3.3 (*WlanCounters 3) For future use Counter *WlanFramesDropped 710.3.
PAGE 222
B-24 BreezeACCESS 4.0 System Manual *FramesDroppedVoice 710.3.3. 8.2.3.14 (*WlanCounters 14) Applicable to SU and AU only when the ACSE Option is enabled. Read-only. The number of dropped voice frames, including fax and T.38 redundant frames. The voice frames that were retransmitted to the extent of the maximum allowed number of retransmissions for voice frames without being acknowledged. Counter *TotalRetransmittedFrames 710.3.3. 8.2.3.15 (*WlanCounters 15) Applicable to SU and AU. Read-only.
PAGE 223
Appendix B B-25 *BadFragmentsReceived 710.3.3. 8.2.3.31 (*WlanCounters 31) Applicable to SU and AU. Read-only. The number of frames received from the wireless media with errors (CRC errors). Counter *DuplicatedFramesDiscarded 710.3.3. 8.2.3.32 (*WlanCounters 32) Applicable to SU and AU. Read-only. The number of frames discarded due to receiving multiple copies. Counter *InternallyDiscardedMirCir 710.3.3. 8.2.3.33 (*WlanCounters 33) Applicable to SU and AU. Read-only.
PAGE 224
BreezeACCESS 4.0 System Manual B-26 *ReceivingUnits 710.3.3. 8.3 (*SiteSurvey 3) *AveragePower 710.3.3. 8.3.1 (*ReceivingUnits 1) Applicable to SU only. Read-only. Represents the average Signal Strength of received frames. DisplayString (SIZE(32)) *RssiOrDbm 710.3.3. 8.3.2 (*ReceivingUnits 2) Applicable to SU and AU. Selects the measurement units used to display the average received signal strength. Integer rssi (0) dBm (1) *PerHopStatistics 710.3.3. 8.4 (*SiteSurvey 4) Applicable to SU and AU.
PAGE 225
Appendix B B-27 *AdbTxFrames3M 710.3.3. 8.5.2.1.8 (*AdbEntry 8) Applicable to AU Only. Read-only. Counts the total number of frames (excluding retransmissions) that were transmitted to the SU over the wireless link at 3Mbps. Counter *AdbRTxTotal 710.3.3. 8.5.2.1.9 (*AdbEntry 9) Applicable to AU Only. Read-only. Counts the total number of frames that were retransmitted to the SU over the wireless link. Counter *AdbRTx1M 710.3.3. 8.5.2.1.10 (*AdbEntry 10) Applicable to AU Only. Read-only.
PAGE 226
BreezeACCESS 4.0 System Manual B-28 Special Operations Parameters MIB Parameter (Location in Parenthesis) Description Values/Range Applicable to AU and SU. Read-only. Identifies the product family/band: DisplayString (SIZE(15)) (2.4 (BreezeACCESS II), MMDS, 2.6a, 2.6b, 3.3a, 3.5a, 3.5a1, 3.5b, 3.5ab, 3.6b, 3.8, 5.7(SD), 5.7 (D,D)) *SpecialOp 710.3.3. 9 (brzAccessMib 9) *RadioBand 710.3.3. 9.1 (*SpecialOp 3) Note: Additional Special Operations parameters are reserved for factory use only.
PAGE 227
Appendix B B-29 Unit Control Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *ResetUnit 710.3.3. 10.1 (*UnitControl 1) Applicable to all products. Resets the unit and applies new parameter values. Integer cancel (0) resetSystemNow (1) *SetDefaults 710.3.3. 10.2 (*UnitControl 2) Applicable to all products. Sets unit configuration to Defaults values after the next reset.
PAGE 228
BreezeACCESS 4.0 System Manual B-30 *EventLogPolicy 710.3.3. 10.10.1 (*EventLog 1) Applicable to all products. Determines which events will be stored in the Event Log. Event from the configured level and higher are stored and can be displayed using the Monitor or by getting a the log file using TFTP. Integer logAll (1) message (2) warning (3) error (4) fatal (5) logNone (6) *NumberOfEventsInLogFile 710.3.3. 10.10.2 (*EventLog 2) Applicable to all products. Readonly.
PAGE 229
Appendix B B-31 System Information Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *UnitHwVersion 710.3.3. 13.1 (*SysInfo 1) Applicable to all products. Read-only: Hardware platform version. DisplayString (SIZE(0..32)) *VoiceHwVersion 710.3.3. 13.2 (*SysInfo 2) Applicable only to SU with voice. Read-only: Voice hardware platform version. DisplayString (SIZE(0..32)) *SoftwareVersion 710.3.3. 13.3 (*SysInfo 3) Applicable to all products.
PAGE 230
BreezeACCESS 4.0 System Manual B-32 Alarms Parameters MIB Parameter (Location in Parenthesis) Description *Alarms 710.3.3. 20 (brzAccessMib 20) Alarms parameters *GpsAlarms 710.3.3. 20.1 (*Alarms 1) Applicable to GU only. GPS Alarms parameters. *AlarmInTable 710.3.3. 20.1.1 (*GpsAlarms 1) Applicable to GU only. Names and status of Alarms-In. Not accessible. *AlarmInTableEntry 710.3.3. 20.1.1.1 (*AlarmInTable 1) Applicable to GU only. An Alarms In table entry. Not accessible. *AlarmInIdx 710.3.3.
PAGE 231
Appendix B B-33 brzPhoneMIB (applicable to SU with voice only) breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomPrvRev {breezecom 3} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3 brzPhoneMib {breezecomPrvRev 4 } OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3.4 Note: * is used instead of the phon prefix Dialing Parameters MIB Parameter (Location in Parenthesis) Description Values *PulseDialing 710.3.4.1.
PAGE 232
BreezeACCESS 4.0 System Manual B-34 *FastStart 710.3.4.1.13 (*DialingParams 13) Enables/disables the fast connect protocol. Integer disable (0) enable (1) na (255) *InformTransferCap 710.3.4.1.14 (*DialingParams 14) Defines the value of the information transfer capability in the SETUP message. Integer speech (0) unrestricted (1) restricted (2) audio (3) unrestrictedTones (4) video (5) na (255) *DTMFRelay 710.3.4.1.15 (*DialingParams 15) Disable/enable DTMF Relay. 0 ñ Disable.
PAGE 233
Appendix B B-35 *AlternateGkOption 710.3.4.1.24 (*DialingParams 24) Setting the Alternate Gatekeeper feature. EnableManualDiscovery: the Alternate Gatekeeper IP address is specified by the Alternate Gatekeeper IP Address parameter. EnableAutomaticDiscovery: the Alternate Gatekeeper IP address is received from the Primary GK. Integer disable (0) enableManualDiscovery (1) enableAutomaticDiscovery (2) na (255) *AlternateGkIPAddress 710.3.4.1.
PAGE 234
BreezeACCESS 4.0 System Manual B-36 *VoiceCodec 710.3.4.2.4 (*VoiceParams 4) The relative priority of voice codecs. DisplayString (SIZE (0..120)) A priorities vector of up to 7 different numbers in the range 1-7, where 1=G.723.1 2=G.729 3=G.711 uLaw 64k 4=G.711 Alaw 64k 5=G.729AnnexA 6= G.729wAnnexB 7= G.729AnnexAwAnnexB *VoiceActivityDetection 710.3.4.2.5 (*VoiceParams 5) Enables or disables the voice activity detection (VAD) feature when using G7231 codec.
PAGE 235
Appendix B B-37 Telephony Signals MIB Parameter (Location in Parenthesis) Description Values *TelephonyCountryStandard 710.3.4.3.1 (*TelephonySignals 1) The country standard for call progress tones, ringer and timeouts. INTEGER proprietary (1) germany (2) sweden (3) france (4) unitedKingdom (5) belgium (6) usa (7) chile (8) na (255) *TonesTable 710.3.4.3.2 (*TelephonySignals 2) A table of parameters of the tones.
PAGE 236
BreezeACCESS 4.0 System Manual B-38 *TimeOuts 710.3.4.3.3 (*TelephonySignals 3) Time Out parameters. If the *TelephonyCountryStandard is set to proprietary, the Time Out parameters may be configured (read/write). For all other country standards, the values are readonly. *MinimumFlashDetectTimeOut 710.3.4.3.3.1 (*TimeOuts 1) The minimum on-hook time for identifying it as a Hook Flash. Integer 0-2,000 (milliseconds) *MaximumFlashDetectTimeOut 710.3.4.3.3.
PAGE 237
Appendix B B-39 Supported Traps Note: * is used instead of the brzacc prefix Trap Associated Parameters MIB Parameter (Location in Parenthesis) Description Values *TrapSUMacAddr 710.3.3.14.1 (*Traps 1) Applicable to AU only. SU MAC address. MAC address *TrapRssiQuality 710.3.3.14.2 (*Traps 2) Applicable to SU only. RSSI level of the received signal. Integer *TrapLastRssiQuality 710.3.3.14.3 (*Traps 3) Applicable to SU only.
PAGE 238
BreezeACCESS 4.0 System Manual B-40 Traps Trap (Number) Description Variables *SUassociatedAUTRAP(2) An AU trap indicating a new association with an SU. *TrapSUMacAddr *AUdisassociatedTRAP(3) An AU trap indicating that an SU has been disassociated from the AU. The AU decides that an SU has been disassociated from it and remove it from the ADB after receiving from another AU a SNAP frame with the SU MAC address.
PAGE 239
Appendix B B-41 BreezeACCESS 4.
PAGE 240
B-42 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 241
Appendix C: RSSI to dBm Conversion Table RSSI 71 72 74 75 77 78 81 82 83 84 85 86 88 89 90 91 92 93 94 96 97 98 99 100 101 102 103 104 105 106 107 108 110 111 112 113 dBM -100 -99 -98 -97 -96 -95 -94 -93 -92 -91 -90 -89 -88 -87 -86 -85 -84 -83 -82 -81 -80 -79 -78 -77 -76 -75 -74 -73 -72 -71 -70 -69 -68 -67 -66 -65 RSSI 114 115 116 118 119 120 121 122 123 125 126 127 128 129 130 131 133 134 135 136 137 138 139 141 142 143 144 145 146 148 149 150 151 152 153 dBM -64 -63 -62 -61 -60 -59 -58 -57 -56 -55 -54
PAGE 242
C-2 Manual Revision: 1.01 BreezeACCESS 4.
PAGE 243
Appendix D: Parameters List Unit Control Parameters Parameter Unit Range Default Run-Time Updated Change Unit Name All Up to 32 printable ASCII characters Empty String Yes Change Read-only Password All Up to 8 printable ASCII characters public Yes – For access from Monitor or Telnet only Change Installer Password All Up to 8 printable ASCII characters user Yes – For access from Monitor or Telnet only Change Administrator Password All Up to 8 printable ASCII characters private Yes – F
PAGE 244
BreezeACCESS 4.0 System Manual D-2 Site Survey Parameters Parameter Unit Range Default Run-Time Updated RSSI Display Option AU, SU RSSI, dBm RSSI Yes IP Parameters Parameter Unit Range Default Run-Time Updated IP Address All IP address 10.0.0.1 No Subnet Mask All IP address 255.0.0.0 No Default Gateway Address All IP address 0.0.0.
PAGE 245
Appendix D D-3 Air Interface Parameters Parameter Unit Range Default Run-Time Updated ESSID AU, SU Up to 31 printable ASCII characters ESSID1 No Operator ESSID Option AU Disable, Enable Enable No Operator ESSID AU Up to 31 printable ASCII characters ESSID1 No Hopping Sequence AU Depends on hopping standard 1 No Hopping Set AU 1-3 1 No Hopping Sync AU Idle, Master, Slave Idle No Best AU Support SU Disable, Enable Disable No Number of Scanning Attempts SU 1 – 255 2
PAGE 246
BreezeACCESS 4.0 System Manual D-4 ACSE Number Of Retransmissions For Data AU, SU 0 – 100 6 No ACSE Number Of Retransmissions For Voice AU, SU with voice 0 – 100 30 No Manual Revision: 1.
PAGE 247
Appendix D D-5 Network Management Parameters Parameter Unit Range Default Run-Time Updated Access To Network Management AU, SU From Wlan Only, From Ethernet Only, From Both Ethernet & Wlan From Both Ethernet & Wlan No Network Management Filtering All Disable, Activate Management IP Filter On Ethernet Port, Activate Management IP Filter On Wlan Port (not available in GU), Activate Management IP Filter On Both Ethernet & Wlan Ports (not available in GU), Disable No Set Network Management IP A
PAGE 248
BreezeACCESS 4.
PAGE 249
Appendix D D-7 Parameter Unit Range Default Run-Time Updated ARP Broadcast Override Filter SU Disable, Enable Disable Yes LAN to WLAN Bridging Mode AU Reject Unknown, Forward Unknown Forward Unknown Yes Bridge Aging Time AU, SU 100 – 2000 seconds AU, SU-BD, SU-BD1V: 300 All other SUs: 1800 No Broadcast Relaying AU Disable, Enable Enable No Unicast Relaying AU Disable, Enable Enable No Performance Parameters Parameter Unit Range Default Run-Time Updated RTS Threshold AU,
PAGE 250
BreezeACCESS 4.0 System Manual D-8 Service Parameters Parameter Unit Range Default Run-Time Updated User Filtering Option SU Disable, IP Only, User Defined Addresses Only, PPPoE Protocol Only Disable Yes Set User Filter Address SU IP address (8 entries) 0.0.0.0 (all 8 entries) Yes Set User Filter Mask SU IP address (8 entries) 255.255.255.
PAGE 251
Appendix D D-9 Voice Parameters Parameter Unit Range Default Run-Time Updated Volume SU with voice -20 to 0 (dB) -3dB Yes Echo Cancellation SU with voice Disable, Enable Enable Yes Voice Codec SU with voice 1 – 7654321 (use only the digits 1 – 7) 2134 No G723 Frames Per Packet SU with voice 1–8 2 No G729 Frames Per Packet SU with voice 1 – 12 6 No G711 u-Law Frames Per Packet SU with voice 1 – 16 12 No G729 Frames Per Packet SU with voice 1 – 16 12 No Voice Activity
PAGE 252
BreezeACCESS 4.0 System Manual D-10 Dialing Parameters Parameter Unit Range Default Run-Time Updated Pulse Dialing SU with voice Disable, Enable Enable No Gatekeeper Option SU with voice Disable, Enable Disable No Gatekeeper / Gateway IP Address SU with voice IP address 0.0.0.0 No Alternate Gatekeeper Option SU with voice Disable, Enable Disable No Alternate Gatekeeper IP Address SU with voice IP address 0.0.0.
PAGE 253
Appendix D D-11 Parameter Unit Range Default Run-Time Updated Endpoint Type SU with voice Terminal, Gateway Terminal No Fax Relay Option SU with voice Disable, Enable Disable No Fax Relay redundancy SU with voice 0–5 3 No Batter Polarity SU with voice (Voice card rev. D and higher) Forward Battery, Reverse Battery, Forward->Reverse Battery, Reverse->Forward Battery Forward Battery No Caller ID SU with voice (Voice card rev.
PAGE 254
BreezeACCESS 4.
PAGE 255
Appendix D D-13 Parameter Unit Range Default Run-Time Updated Cadence Off SU with voice 100-10,000 milliseconds Dial Tone: Ring Back: 3000 Busy: 500 Congestion: 1000 Error: 200 High Level Error: 0 Ring Frequency: 3000 No Duration SU with voice 0 – 10,000 seconds Dial Tone: 15 Ring Back: 60 Busy: 15 Congestion: 0 Error: 0 High Level Error: 0 Ring Frequency: 60 No Min. Flash Detect Timeout SU with voice 0-2,000 milliseconds 120 No Max.
PAGE 256
BreezeACCESS 4.
PAGE 257
Index A Access Link Parameter .......................................................................Book 4, 2-46 Access to DHCP Parameter ...............................................................Book 4, 2-22 Access to Network Management Parameter ......................................Book 4, 2-41 Access Units AU-A/E-NI ...................................................................................Book 1, 2-7 Acknowledge Delay Limit Parameter ................................................
PAGE 258
B Bad fragments received Parameter .................................................... Book 4, 2-14 Base Station Equipment ..................................................................... Book 1, 2-4 Basic Configuration Menu ................................................................. Book 4, 2-10 Basic Parameters Configuring .................................................................................. Book 3, 1-5 Battery Polarity Parameter ...................................................
PAGE 259
Configuring Basic Parameters .....................................................Book 3, 1-5 GU-A-BS .....................................................................................Book 3, 1-10 RSSI and Maximum Data Rate ....................................................Book 3, 2-2 Compression Efficiency Parameter ....................................................Book 4, 2-63 Configuring Basic Parameters ..........................................................................
PAGE 260
58, Book 4, 2-78 E Echo Cancellation Parameter ............................................................. Book 4, 2-63 Endpoint Type Parameter .................................................................. Book 4, 2-69 Enhanced Mode Spanning Factor ...................................................... Book 4, 2-27 Erase Event Log Parameter ............................................................... Book 4, 2-9 Erase Manual Sequence ................................................................
PAGE 261
H H323 Terminal ID Parameter .............................................................Book 4, 2-65 High Level Error Tone Parameter ......................................................Book 4, 2-72 Hopping Parameters Menu .................................................................Book 4, 2-77 Hopping Shift .....................................................................................Book 4, 2-28 Hopping Sync ...................................................................................
PAGE 262
Manual Sequence Definition ............................................................. Book 4, 2-26 Max. Flash Detect Timeout Parameter .............................................. Book 4, 2-73 Maximum ACSE Voice Sessions Parameter ..................................... Book 4, 2-40 Maximum Burst Duration Parameter ................................................ Book 4, 2-60 Maximum Data Rate Configuring ..................................................................................
PAGE 263
MIR/CIR Option Parameter ...............................................................Book 4, 2-60 Multi-Rate Decision Window Size Parameter ...................................Book 4, 2-57 Multi-Rate Support Parameter ...........................................................Book 4, 2-57 N Network Management Filtering Parameter ........................................Book 4, 2-41 Network Management Parameters .....................................................
PAGE 264
R Rate Parameter ................................................................................... Book 4, 2-57 Receive Attenuation Control Parameter ............................................ Book 4, 2-39 Registration TTL Parameter .............................................................. Book 4, 2-68 Remove Forwarding VLAN ID Parameter ........................................ Book 4, 2-49 Remove Frequencies Parameter ........................................................
PAGE 265
AU-A/E-NI ...................................................................................Book 1, 3-7 Configuration and Managemen ....................................................Book 1, 3-4 Data Communication ...................................................................Book 1, 3-3 Environmental ..............................................................................Book 1, 3-5 GU-RA GPS Radio ......................................................................
PAGE 266
Total Tx errors Parameter .................................................................. Book 4, 2-14 Traffic Statistics ................................................................................. Book 4, 2-12 Transmit Power Control Parameter ................................................... Book 4, 2-36 Transmitted wireless to Ethernet Parameter ...................................... Book 4, 2-12 Trunk Link Parameter ........................................................................
PAGE 267
Volume Parameter ..............................................................................Book 4, 2-63 W WEP KEY # Parameter ......................................................................Book 4, 2-62 Wireless Link Counters ......................................................................Book 4, 2-13 WLAN Aging Time Parameter ..........................................................
PAGE 268