STREAK 1000 OCTOCOPTER Instruction Manual 1
Contents 1. Safety Notes........................................................................................................................................................3 2. Check List............................................................................................................................................................4 3. Equipment Required For Assembly....................................................................................................................
1. Safety Notes Do fly only in safe areas and always away from other people! Do not operate RC aircraft within the vicinity of homes or crowds of people. RC machine are prone to accidents, failures, and crashes due to a variety of reasons including pilot error, radio interference, and lack of maintenance. Pilot are responsible for their actions and damage or injury occuring during the operation of RC aircraft machine.
2. Check List Please Check the Follow parts. Apc Propeller 14x4.7SFP (CW) 4 Pcs Apc Propeller 14x4.7SFP (CCW) 4 Pcs Large Current Power/ESC Board (Black/ Blue color) with 2 pairs Battery Cable. Servo Extension Wire ( 30cm ) 8 pcs AWG wire Red ( 45cm ) 8 pcs AWG wire Black ( 45cm ) 8 pcs 1pcs x Direction Indicating Sticker Alware Brushless Motor 351515 KV400 (Not included unless otherwise specified.) 6 Set Screw set come with Motor.
Battery Support Damper 8pcs Spare Screw Pack 1pcs Frame Parts: Main Frame Assembly 1 set FPV & GPS Mounting Assembly Motor Mount with Quick Lock 1Pcs (left) Mount Assembly Landing Gear Frame Assembly 4 sets 1 Pcs (right) Motor Mount with Fixed Arm Assembly 4 sets Leading Gear Assembly 2 sets 5 Landing Gear Skid (420 mm) 2 pcs
3. Equipment Required For Assembly 40A ESC(6S 22.2V) (e.g. HobbyWing FlyFun 40A ESC) 8 pcs 3.5mm Bullet Connector (Female) for 8pcs ESC 24 pcs “V” Mode OctCopter Controller (e.g. DJI WK-M) 1 pcs Connectors For Batteries and Power Board 2 pairs Transmitter (7CH or above) 1 pcs Receiver (7Ch or above) 1 pcs 6S Lipo Charger 1pcs 6S LiPo Battery 3500-7500mAh 22.
4 Assembly Steps – Motor and ESC Soldering Step 1. You will received 8 motors in ALS1000CB. Step 2. For the new motors, Thread Lock must be applied to the two M3 Set Screws which is pre-inserted in the motor. (This is a must for safety flying.) Step 3. Step 4. Install the Porp Mount to the motor using 3pcs M3 Double check the prop mount which must be installed Hex Cap Screw. (Apply little amount of Thread Locker to the motor securely. when assembly metal to metal parts.) 1.
5.0 Assembly Steps – Body Step 1. Loosen the screw circled above as to uninstall the Upper Main frame from the Main Frame Assembly. Step 2. Lower Main Frame with Power/ESC Board preinstalled (on the left) and the Upper Main Frame (on the right). Step 3. Step 4. Solder 2 pairs Battery Cable to the Power.ESC Board. Close view of step 3 soldering. Step 5. Prepare four Motor Mount with Fixed Arm Assembly Step 6. Close view of Motor Mount with Fixed Arm Assembly.
Step 7. Loosen the screws of the Lower side. The Hook Side must pointing to the Axis Line of the Lower Main Frame for installation. Step 8. Install the Motor Mount with Fixed Arm Assembly onto the Lower Main Frame. Follow the installation direction as shown above. (Apply little amount of Thread Locker to the screws before installation.) Step 9. Install four Motor Mount with Fixed Arm Assembly onto the specific position of Lower Main Frame. Step 10.
Step 13. Loosen the screws and Quick Lock Mount of the Lower side. The Hook Side must pointing to the Axis Line of the Lower Main Frame for installation. Step 14. Install the Motor Mount with Quick Lock Mount Assembly onto the Lower Main Frame. Follow the installation direction as shown above. (Apply little amount of Thread Locker to the screws before installation.) Step 15. Secure Quick Lock Mount using M3x8mm Screws. (Apply little amount of Thread Locker to the screws before installation.) Step 16.
Step 17. Close view of the Motor Mount Assembly Installation on the Lower Main Frame. Make sure the installation is same as above. Step 18. Insert the Battery Power Cable and Signal Wire of the ESC into the Carbon Boom Arm. Same for all 8pcs ESCs. Step 19. Solder the Battery Power Wires of the ESC to the ESC Board. (Red wire = +ve , Black wire = -ve) Step 20. Solder 2 pairs Battery Cable to the Large Current Power/ESC Board and connect the other end to the Battery Connectors.
Step 21. Install the Upper Main Frame onto the Lower Main Frame Assembly. Secure the screws for the four Motor Mount with Fixed Arm Assembly first. (Apply little amount of Thread Locker to the screws before installation.) Step 22. Secure the screws with 3mm Washer for the four Motor Mount with Fixed Arm Assembly. (Apply little amount of Thread Locker to the screws before installation.) Step 23. (Apply little amount of Thread Locker to the screws before installation.
Step 21. Step 22. Install the Landing Gear Frame Assembly onto the Secure the Booms. Lower Main Frame using M3x10mm Screws from step 7. (Apply little amount of Thread Locker to the screws before installation.) Step 23. Secure the all Booms using the pre-installed M3 screws on the Motor Mount Assemblies. (Make sure all 8 Booms are completely secured.) Step 24. Perform Part 6. Quick Collapsible Illustration shown bellow as to check the folding mechanism of for arms.
5.1 Assembly Steps – FPV and GPS Mount Step 1. Prepare the FPV & GPS Mounting Assembly. Step 2. Get ready for the installation of FPV & GPS Mounting Assembly onto Main Body. Step 3. Step 4. Insert the FPV & GPS Mounting Assembly onto Main Indicate the forward flying direction. Body Rib and secure with M2x6mm Hex Cap Screws. (Apply little amount of Thread Locker to the screws before installation.
5.2 Assembly Steps - Flight direction indicator Step 1. Cut the Direction Indicating Sticker with a width of around 100mm. Step 2. Tear the cover layer of the Sticker before stick to the front Carbon Arm Boom. Step 3. Indicate the forward flying direction. Step 4. Stick the Direction Indicating Sticker (100mm Width) to the two Carbon Arm Boom in the forward flying firection. And use three pieces of Adhesive Tape to secure the Direction Indicating Sticker.
5.3 Assembly Steps – Motors and Props Step 1. Prepare 4pcs M3x8mm HexCap Screws with 4pcs 3mm Washers to install the motors to the Motor Mounts. Step 2. Insert a M3x8mm Screw into a 3mm Washer then insert to the motor mount slot as to mount the Motor to it. (Apply little amount of Thread Locker when assembly metal to metal parts.) Step 3. Secure the motor to the motor mount with 4pcs screws and washers. Step 4. Insert the Motor Wires into the slot of motor mount and connect with motors.
Step 5. Repeat Step 1 to 4 for other 7 motors. Test the motor first without propellers as to ensure the rotating direction is correct. Exchange any two motor wires to the ESC as to reverse the direction if needed. Step 6. After ensuring the motors are running in the correct direction, prepare the APC Props and Prop mounting screw and washer from the motors. Step 7. Insert the Root Hole Adapter (with 6mm inner diameter) to the bottom side of APC Prop. Step 8.
5.4 Assembly Steps – Bipod Landing Gear. Step 1. Step 2. Insert the Landing Gear Skid into the mounting hole of Adjust the length of the Landing Gear Skid. Each side Carbon Fiber Leading Gear Assembly. (Tips: You can of the Landing Gear Skid should be about 195mm. rotate the Landing Gear Skid into the hole with less effort.) Step 3. Secure Landing Gear Skid onto the Carbon Fiber Leading Gear Assembly using the M3 Set Screw which is pre-installed on the Landing Gear Skid Metal Mount. Step 4.
Step 5. Correct two Bipod Landing Gear Assemblies. Step 6. Insert the Carbon Boom of Bipod Landing Gear Assembly into the metal mount of Landing Gear Frame Assembly with the depth of approximately 5mm. Step 7. Adjust the Bipod Landing Gear Assembly to make the Landing Gear Skid be parallel to the Landing Gear Frame Assembly frame. And secure the Landing Gear Frame Assembly with the M3 Screws.
5.5 Assembly Steps – Multicopter Controller Mounting Illustration. Overall electronics mounting for reference. Installation of WK-M, Front View. Back View. GPS Compass mounting for reference.
6. Quick Collapsible Illustration With the Quick Collapsible Design, you can fold four arms of Streak 1000 easily for easy transportation and storage. However you must follow the coming step by step to fold the arms correctly, otherwise the Lock System may damaged! Step 1. Four Arms of Streak 1000 are locked with four Thumb Screws with Split Lock Washers. Lower Main Frame Side Upper Main Frame Side Step 2. Loosen the above Screws a little bit (normally loosen 0.
Step 3. Loosen the Thumb Screw and make sure it is not touching the Fiber Frames. Then the four Folding Arms can be folded or opened. Step 4. Make sure the Arm is fully folded or opened, and then tighten the Thumb Screw completely. It should throught two layer of the carbon fiber frames as shown above for secure flying. Step 5. Always check if the above four Screws on the Upper Main Frame are secured tightened completely for secure flight.
7. Gimbal Mounting Illistration Step 1. Indicate the Multi-Gimbal Mount which is installed with Landing Gear Frame Assembly. Step 2. Mounting position for GAUI CRANE 3 and CRANE 2 Gimbals. Lensman series professional Gimbals will be available soon.. Step 3. Mounting positions for other Gimbals such as STO S903(3-axis) Gimbal, STO Camera Mount Kit S-550 etc.
8. Specification Kit: -Diagonal Wheelbase: 1030mm -Motor Mounting Frame Size: Φ13x22-34mm(Shaft x Screw Diagonal Distance) -Bipod Landing Gear Dimension: 188mm(Top Width) x 466mm(Lower Width) x 348mm(Height) -Landing Skid Pipe: Φ10x420mm -Bipod Landing Gear Weight: 136g -Total Kit Weight: 1400g (Approx.)(Without Electronics & Props) -Total Weight with Motors, Props, 40A ESCs, WK-M: 3.5kg Carbon Arm Booms: -Length: 380mm -Weight: 35.
-Input voltage: 22.2V 6S LiPo Battery -Max continuous current: 35A(180sec) -Max output power: 750W(180sec) -Internal resistance: 175mOHM -Recommended ESC: HobbyWing 40A/ 60A Speed Controller/ ESC: -Current: 40A or Above -Voltage: 22.2V 6S LiPo -Largest Dimension: 30x80x25mm (WxLxH) -Recommended ESC: HobbyWing 40A ESC(for 22.2V 6S Lipo) # Report any mistakes, please email to: info@alwarerc.com Related Videos could be found on: http://www.youtube.
