Owner Manual (FULL)

ManualsBrandsAlwyn Home ManualsBed FramesAshland 8.3'' Platform Bed

Table Of Contents

ASSE

MBLY INSTRUCTION

Rail Support Bar

Thi

s page lists all the contents included

in the box. Please take the time to

identify the hardware as well as the

individual components to this product.

As you unpack and prepare for

assembly, place the contents on a

carpeted or padded area to protect

them from damage.

Ratchet Tool

4mm

METAL FULL BED FRAME

Rail Side Connector

Bar

Wrench

1/4"

16PC

Bolt

1/4"*16mm

20PC

Slat Connector

PCS

Rail Left Section

PCS

ail End Connector

Bar

Center Support Rail

Slat

20PCS

Bolt

1/4"*35mm

PCS

2PCS

Nut

1/4"

PCS

Bolt

3/16"*16mm

Slat Connector - Middle

10PC

PCS

Bolt

1/4"*50mm

PCS

24PC

Rail Down Section

PCS

ail Right Section

PCS

Summary of content (5 pages)

PAGE 1
ASSEMBLY INSTRUCTION METAL FULL BED FRAME Rail Left Section Rail Right Section Rail Down Section Rail Support Bar 2PCS Rail Side Connector Bar 2PCS Rail End Connector Bar 4PCS Center Support Rail 8PCS Slat 2PCS Slat Connector 2PCS Slat Connector - Middle 2PCS Bolt 1/4"*35mm 24PCS Bolt 1/4"*50mm 20PCS Bolt 1/4"*16mm 10PCS Bolt 3/16"*16mm 20PCS Nut 1/4" 2PCS Ratchet Tool 4mm 16PCS Wrench 1/4" 6PCS 2PCS 1PC 1PC This page lists all the contents included in the box.
PAGE 2
How to Use the Ratchet Tool (P) 1. Before assembling the furniture, please adjust the lock as needed. Lock on the right to loosen bolts! Lock on the left to tighten bolts! 2. Tighten or loosen bolts. Tighten bolts: Locate the turncap and rotate it clockwise to screw the bolt quickly until it cannot be rotated any more. Then start rotating the handle clockwise to finalize tightening the bolt. Turncap Handle Loosen bolts: Rotate the handle counterclockwise to loosen the bolt.
PAGE 3
Attach Rail Support Bar (D) to Rail Sections (A) & (C), insert the Bolt (K), turn the Ratchet Tool (P) to tighten them. Attach Rail Support Bar (D) to Rail Sections (B) & (C), insert the Bolt (K), turn the Ratchet Tool (P) to tighten them. P K A B D D C A C D K A D D C D D C B C D D Attach the Rail End Connector Bar (F) to the assembled rails, insert the Bolt (M), turn the Ratchet Tool (P) to tighten them.
PAGE 4
Attach the Slat (H) to the Center Support Rail (G) and Rail Sections (A) & (B), insert the Bolt (N), turn the Ratchet Tool (P) to tighten them. PH A H N H H G H B B P N A H G G H A H H G H B Attach two Center Support Rail (G) together, insert the Bolt (L) and Nut (O), turn the Ratchet Tool (P) and Wrench (Q) to tighten them. Attach the Rail Side Connector Bar (E) to the assembled rails, insert the Bolt (M), turn the Ratchet Tool (P) to tighten them.
PAGE 5
7 Attach the Slat (H) to assembled rails, put the Slat Connectors (J) & (I) into the correct places and press them down. J I H B G H H B I J A H G A G B Cleaning & Care Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time. Periodically check that all connections are tight.