Installation guide

]NST TION REQUIREMENTS
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with any tools
listed here.
All installations
Tools needed:
Piers
Phillips
screwdriver
5/t8"and 1/4"
nut drivers or
hex sockets
Measuring tape
or ruler
Flat-blade
screwdriver
Utility knife
UL Listed/CSA _
Approved twist-on_J U
wire connectors* v v
Small level
10" adjustable wr_
that opens to
11/8" (2.9 cm)
*Must be the proper size to connect your household wiring to 16
gauge wiring in dishwasher
Other useful items you may need:
F ash ght _/_ I Bath towel _---_
Parts supplied:
Drain hose clamps (2) Drain hose
(1 large and 1 small )
Make sure all these parts are included in the literature package.
Parts needed:
90,! E bowfi_ting With Tefl0n®taPe oi pipe j0int--
% NIRT. external threads i €0mpound
(the other end must fit Y0ur /,-_-,_
Other parts you may also need:
11/2"' 2!' : ISi demounti_gk it: I Mas_ing_ I
(38,!-5 cm) _q Ifor solid surface I duct tape
Screw4ype I c2untert°P,s I I
clam . _r'ar[ i_umDer
PS (3 max'mum)J 8212560) [ I
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
in addition, for first time installations
Tools needed:
cordless drill
with
and 11/2'!hole small
Sawbits tubing cutter Wire stiippei
Parts needed:
I
Copper tubing (3/8" See "Electrical Requirements" section
O.D.suggested) or __ _: . . ,. _ ,, ,
flexible braided t-0r Lhrect Wire: r0r rowerbuppjy
water su,,,,i, li--e i use UL Listed/ Cord: use UL
" CSA Approved listed power
J strain relief suppiycord ki t
_\t_/,_t,_ _/)))_,)to fit 7/8 (2.2 cm) marked for use
wi!hd!shwashe!
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
wa rra nty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277)is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
• easy access to water, electricity and drain.
• convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (if floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
if dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Product and Cabinet Opening Dimensions" section.
• Teflon is a registered trademark of E.I. Du Pont de Nemours and Company. 3