Installation Guide

ManualsBrandsAmana ManualsOtherAEP222VAW

INSTALLATION INSTRUCTIONS

20" (50.8 CM) FREESTANDING ELECTRIC RANGE

with Standard Clean Oven

Table of Contents

RANGE SAFETY .............................................................................2

INSTALLATION REQUIREMENTS................................................3

Tools and Parts ............................................................................3

Location Requirements................................................................3

Electrical Requirements ...............................................................5

INSTALLATION INSTRUCTIONS..................................................6

Unpack Range..............................................................................6

Install Anti-Tip Bracket.................................................................6

Electrical Connection...................................................................7

Verify Anti-Tip Bracket Is Installed and Engaged......................11

Level Range................................................................................12

Complete Installation .................................................................12

Check Operation........................................................................12

W10459122A

IMPORTANT:

Save for local electrical inspector's use.

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 20" (50.8 CM) FREESTANDING ELECTRIC RANGE with Standard Clean Oven Table of Contents RANGE SAFETY .............................................................................2 INSTALLATION REQUIREMENTS ................................................3 Tools and Parts ............................................................................3 Location Requirements................................................................3 Electrical Requirements ............................
PAGE 2
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
PAGE 3
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed ■ Tape measure ■ Masking tape ■ Flat-blade screwdriver ■ Wire strippers ■ Phillips screwdriver ■ ³⁄₈" nut driver ■ Level ■ ■ Hammer ¹⁄₈" (3.2 mm) drill bit (for wood floors) ■ Hand or electric drill ■ ■ Wrench or pliers ■ Marker or pencil ³⁄₁₆" (4.
PAGE 4
Product Dimensions Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. If the cabinet depth is greater than 24" (61.0 cm), the oven frame must extend beyond cabinet fronts by ½" (13.0 mm) minimum.
PAGE 5
Electrical Requirements If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge is in accordance with local codes. Do not use an extension cord. Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances.
PAGE 6
INSTALLATION INSTRUCTIONS Unpack Range WARNING Install Anti-Tip Bracket WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Do not use oven door handle to lift or move the range. 2. Remove shipping materials, tape and film from range. Keep cardboard bottom under range. Remove oven racks and parts package from inside oven. 3. Take 4 cardboard corners from the carton. Stack one cardboard corner on top of another.
PAGE 7
Floor Mounting Rear position 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1⁵⁄₈" screws provided. 6. Move range close enough to opening to allow for final gas and electrical connections. Remove shipping base, cardboard or hardboard from under range. 7. Move range into its final location, making sure rear leveling leg slides into anti-tip bracket. Front position Diagonal (2 options) Wall Mounting 8.
PAGE 8
■ Tighten strain relief screw against the power supply cord. ■ Feed the flexible conduit through the strain relief, allowing enough slack to easily attach wiring to the terminal block. ■ Tighten strain relief screw against the flexible conduit. Style 2: Direct wire strain relief Use Phillips screwdriver to remove screws and rotate/ conduit plate 180º. ■ 4. Replace back panel and screws on rear of range. 5.
PAGE 9
2. Use Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw. 3. Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. 3-wire connection: Power Supply Cord Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord. 1.
PAGE 10
Direct Wire Installation: Copper or Aluminum Wire This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection. 1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire. 4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires.
PAGE 11
3. Use ³⁄₈" nut driver to connect the bare (green) ground wire to the center terminal block post with one of the 10-32 hex nuts. 3-wire connection: Direct Wire Use this method only if local codes permit connecting ground conductor to neutral supply wire. 1. Pull the conduit through the strain relief on cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. F A E B A B D C D F E D. Line 2 (red) wire E. Bare (green) ground wire F.
PAGE 12
Check the operation of the cooktop elements: 1. Push in and turn each surface element control knob to the High position. Check the operation of the cooktop elements and indicator lights. A RIGHT REAR RIGHT FRONT OFF OFF LO 9 9 2 3 8 LO HI 8 HI 3 SURFACE 7 5 7 4 4 5 6 6 Level Range 1. Place rack in oven. 2. Place level on rack and check levelness of range, first side to side; then front to back. 3.