Owner`s manual

ManualsBrandsAmana ManualsAir ConditionerVTC Series

December 1999 20292301

S P V U

Single Package Vertical

Air Conditioner/Heat Pump

Installation Instructions

and Owner’s Manual

VTC/VTH Series

The Single Package Vertical Unit is a compact, through the wall pack-

aged HVAC system that can be ducted to individual rooms. It’s slim 20” wide

design uses minimal floor space and installs in a closet having an exterior wall.

Conditioned air from a single unit can be ducted to multiple rooms. Each unit

is controlled by a standard wall thermostat.

These instructions give information relative to the SPVU unit only. Refer

to Wall Sleeve and Grille installation instructions for those components. The

manufacturer assumes no responsibility for equipment installed in violation of

any code requirements. For other related equipment refer to the proper

instructions.

Summary of content (9 pages)

PAGE 1
SPVU December 1999 Single Package Vertical Air Conditioner/Heat Pump Installation Instructions and Owner’s Manual VTC/VTH Series The Single Package Vertical Unit is a compact, through the wall packaged HVAC system that can be ducted to individual rooms. It’s slim 20” wide design uses minimal floor space and installs in a closet having an exterior wall. Conditioned air from a single unit can be ducted to multiple rooms. Each unit is controlled by a standard wall thermostat.
PAGE 2
Contents Unit Features ............................................................... 3 Unit Location ............................................................... 3 Transportation Damage .............................................. 3 Unit Accessories ......................................................... 3 Installation Instructions .............................................. 4 Wiring ........................................................................... 5 Operating Instructions ............
PAGE 3
1. Make notation on delivery receipt of any visible damage to shipment or container. 2. Notify carrier promptly and request an inspection. 3. In case of concealed damage, carrier must be notified as soon as possible—preferably within 5 days. 4. File the claim with the following supporting documents within the 6 month statute of limitations. a. Original Bill of Lading, certified copy, or indemnity bond. b. Original paid freight bill or indemnity in lieu thereof. c.
PAGE 4
• Ensure a minimum clearance of three (3) inches around the unit for adequate airflow. • Ensure the condensate drain is unobstructed and leakfree. Installation Instructions To ensure that the unit operates safely and efficiently, it must be installed, operated and maintained according to these installation and operating instructions and all local codes and ordinances or, in their absence, with the latest edition of the National Electric Code.
PAGE 5
UNIT INSTALLATION 1. Lift the unit onto the base of the sleeve and slide the unit forward until it is 1/2” away from the top inside edge of the sleeve to engage the seal. Ensure the unit is completely seated on all four sides against the wall sleeve seals. Figure 4 Wiring WARNING To avoid the risk of electrical shock, personal injury or death, do not service this unit without first opening all disconnects. Figure 3 2. Connect properly sized electrical service to the quick disconnect. 3.
PAGE 6
The unit comes with a factory-supplied quick disconnect, however, the contractor is responsible for providing over current protection on the branch circuit. Refer to the unit wiring diagram for single point electrical connection. Operating Instructions Operation of the unit is automatic and will provide heating and cooling depending on the setting of the thermostat. These units are provided with a Class 2 transformer for 24 volt control circuits.
PAGE 7
System Checks COOLING/ELECTRIC HEAT UNITS POINT CHECK ACTION Set thermostat system switch to OFF position. None. Unit does not come on. Set fan switch to ON. Indoor blower operates after random reset timer cycle is complete. Set fan switch to AUTO Indoor blower de-energizes. Set system switch to COOL and lower thermostat set point to coldest setting. The compressor, outdoor fan, and indoor blower energizes after a 5minute startup delay.
PAGE 8
Care and Cleaning Obtaining Service PERIODIC MAINTENANCE Clean the outdoor coil of foreign material such as lint, dust, leaves or other obstructions as necessary. Check drain line and removing obstructions as necessary. In the unlikely event this unit requires repair or servicing beyond what is covered in this manual, contact an authorized service organization.
PAGE 9
Wiring Diagram YEL YEL EVAP. MOTOR COND. MOTOR COMPRESSOR BRN HEATER 1 RED YEL YEL BLK BLK BRN BLK CAP OFF ANY UNUSED SPEED TAPS BLK RED BLUE BLK H C F L1 BLK YEL YEL L1 COMP HTR2 COND EVAP LO EVAP HI L1 L2 YEL L2 GRD L1 208-240V-1PH-60HZ POWER SUPPLY HTR1 L2 A FACTORY SUPPLIED JUMPER IS PLACED BETWEEN FD AND RC AND MUST BE REMOVED WHEN INSTALLING THE FRONT DESK SWITCH.