4700/4800 Series Time Stamp Handling Manual
Proprietary Notice This document contains proprietary information and such information may not be reproduced in whole or part without the written permission from Amano Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey 07068. Amano Cincinnati, Inc. reserves the right to make equipment changes and improvements, which may not be reflected in this document. Portions of this document may have been updated to include the latest hardware or firmware version, if applicable.
Table of Contents Table of Contents.................................................................i Introduction .........................................................................1 Preparation Before Use ......................................................1 How To Take Off The Case.................................................1 How To Operate ..................................................................2 How To Set The Typewheels..............................................
ii 4700/4800 Series Time Stamp Operation Manual
Introduction This manual explains how to use your 4700/4800 Series Time Stamp. You are strongly encouraged to read this manual completely before using the 4700/4800 Time Stamp, and to retain it for future reference. Preparation Before Use (Refer to Fig. 1, 2, & 7) To prevent possible damage of the machine during transit, shock absorbing material has been put inside the machine body (hammer section).
How To Operate • Connect the power cord to an electrical power source. • Insert the papers along the guide line of slide plate for automatic printing (about 5 sheets, if back carboned slips, can be copied). How To Set The Typewheels (Refer to Fig. 2, 3, & 5) • Remove the case, and turn the shaft holder [1] in the arrow direction indicated in Figure 2 to detach it from the shaft [2].
• On releasing the minute advance lever [5], the minute typewheel advances one minute to synchronize with the desired time. Clock Face Typewheels 3 Figure 3. To Set the 4800 Series Model 4850 …4 digit numbers (Year, Month, Date, Hours & Minute) Model 4850 …5 digit numbers )Month, Date, Hours & Minute) • The numbers will be changed automatically upon each printing. • To set the desired number, operate the number wheel advance lever [14] as illustrated in Figure 5.
• To advance the typewheel and clock at the same time, push the minute advance lever [5] (see Figure 5) in the arrow direction, so the typewheel and clock hand advance one minute at the same time. Caution: The setting of the typewheel should be done only right after the minute typewheel is advanced! Shaft 2 Clock Face Clock Advance Gear 4 Figure 4. Figure 5.
How To Change A Ribbon (Refer to Fig. 6 & 7) • In case the print color becomes too light, or the ribbon is cut or crumpled too much, please replace the ribbon with a new one. • First check whether the ribbon reverse turn lever [6] (see Figure 6) is inclined to the inner side of the machine. Incase the lever is inclined to the front, push it in the direction of the inner side.
Ribbon Spool 8 Ribbon Fixer Ribbon Guide Shaft 9 Ribbon Spool 7 Figure 7. Adjustment of Printing Position (Refer to Fig. 8, 9 & 10) 6 • The printing position can be adjusted by moving the knob [11] (see Figures 8 & 9) between 37 mm – 83 mm (1.5” – 3.25”) from the top of the paper. When the upper die plate hammer is taken out, the printing position can be within 16 mm – 83 mm (.66” – 3.25”) from the top of the paper. • For easy setting of the printing position, refer to the mark on the side plate.
Knob for printing adjustment 11 Figure 8. Figure 9.
Printing Sample Figure 10. Incase the printing is required on paper narrower than 65 mm (2 5/8”), install the polyester sheet supplied as accessory in between the bottom case and slide plate as per illustration by placing the sheet so as the edge cut side comes to the right-hand side.
Caution On Use • DO NOT touch the clock hands in any case. • When the printing color becomes light, replace the ribbon with a new one. DO NOT paint with stamping ink as this could injure the machine. • When cleaning the typewheel, carefully remove the dust lodged between the typewheels. For Power Reserve Type Only (Refer to Fig. 11) 1. For Quartz Clock with power reserve type.
NOTES 10 4700/4800 Series Time Stamp Operation Manual
© Copyright 2006 11/06/0