INSTALLATION AND OPERATION INSTRUCTIONS FOR ZERO CLEARANCE AND FREE STANDING UNITS FS-26-922 SAFETY INFORMATION WARNING If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Sierra flame product. IMPORTANT INSTRUCTIONS....................................................................................................................................3 UNPACKING AND TESTING APPLIANCE ..........
IMPORTANT INSTRUCTIONS 1. Read all instructions before installing or using this heater. 2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front of the heater; keep them away from sides and rear as well. 3. Always unplug heater when it’s not in use. 4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the unit has been dropped or damaged in any way. 5. Do not use the heater outdoors. 6.
GROUNDING APPLIANCE This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. To disconnect appliance, turn controls to off, then remove plug from outlet.
FS-26-922 Description Voltage Watts NO HEATER MOTOR HEATER Appliance Width Appliance Height Appliance Depth Gross Weight Plug Location Cord Length BTU This appliance has been tested in accordance with the UL Standard 2021 for fixed and location dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer. Free Standing Appliance 120V AC 60Hz 1500W Max 25W 19W 25 5/8" or 65.2 cm 28" or 71.2 cm 17 1/2" or 44.5 cm 71.
HARD- WIRE INSTALLATION Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance. If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current CSA C22.
MEDIA OPTIONS Your fireplace shipped with the following media: 3 bags of sable glass and an 11 piece log set. Customers can decorate their fireplace according to their wishes with supplied media. This fireplace includes the following decorative media: The glass panel is hooked by 2 hooks on each side. Then you can take off the glass panel.
OPERATION The fireplace can be operated either by the switches located on the left front of the fireplace unit or by supplied remote control. MANUAL OPERATION Push to reveal the manual control panel. (As shows in bellow picture) Push here to open the manual control panel 1. The main power ON/OFF switch in position O, the fireplace is OFF. 2. When main power ON/OFF switch is at position I, the fireplace is ready to use. 3. Press the button repeatedly to set the heater to desired heat setting.
NOTE: If operated at the Low heat setting, the fireplace will not provide as much heat output as in the High heat setting, however the low setting will not require as much electrical power to operate. To avoid overloading a circuit, do not plug the fireplace into a circuit that already has other appliances working. When the fireplace is not in use switch off and unplug. SAFETY CUT-OFF l l This appliance is fitted with a safety cut-off which will operate if the fireplace overheats (eg.
FLASH button: Switches mood light into flash mode, this cycles through all mood light colors. HEATER ON/OFF button: Switching the heater ON/OFF. It has functions of setting memory. HIGHT button: Press the high button to switch the heater to high heat setting 1500W. LOW button: Press the low button to switch the heater to low heat setting 750W. TEMP. button: Press the TEMP. button to switch the heater to AUTO mode.
REPLACEMENT PARTS This list contains replacement parts NO. PART NUMBER DESCRIPTION QTY.
EXPLODED VIEW 13
Wiring Diagram 14
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Dim or no flame Flame LED’s are burnt out Inspect the LED’s and replace them if necessary. Change a flicker and back black cloth.
SERVICE HISTORY This heater must be serviced annually depending on usage.