A90 Robotic Vacuum Cleaner User Manual Please read this instruction carefully before usage and keep it properly
1.Important Safety Instructions • If you have special objects that could potentially be damaged by the bumping,remove these objects from the floor. • Do not let kids sit or stand on Robot. Children and pets should be supervised when Robot is operating. • Do not make Robot for outdoor use. • Do not clean wet messes with your Robot. • Do not use Robot to pick up spills of water bleach, paint, and other chemicals. • Do not keep Robot at a freezing temperatures.
the battery pack near any heat source or direct sunlight, Do not incinerate or short-circuit the battery pack. Do not subject batteries to mechanical shock. Battery and Charging/Information Lithium-ion Battery Important: Lithium-ion batteries and products that contain Lithium-ion are subject to stringent transportation regulations.
(1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications that not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.About Your Amarey A90 ①.Top View ②.
③.
④.
⑤.
3.Using Your Amarey A90 ①.Important Tips Before Using A90 Before robotic vacuum works, please refer to the following guidelines to check the cleaning area. Remove power cords and A90 is not suitable for Anti-fall sensors can prevent Keep A90 away from small objects from the floor long-pile carpet. If the carpet A90 from falling down stairs. spaces lower than 2.4 that may entangle A90. has tassels, please roll up But it may work less inches to prevent A90 from them before usage.
②. Preparations (1)Position the Charging Base on a hard level surface and against a wall. Ensure the place is an open & uncluttered area leaving at least 4ft in the front and 1.6ft on both sides. (2)Connect the round end of the adapter into the power socket on the Charging Dock and the other end into a wall outlet. When connect well, the white light will be on. Otherwise, the robot can’t dock.
(3)Before usage, Please remove the protective strips. protective strip Protective strip (4) Install the side brushes by pressing them into each slot until you hear the a “click”.
(5)Turn on the Main Power Switch at the bottom of Robot (1 refer to power on, 0 refer to power off). The robot can start working after startup music. ③. Charging Robot Place robot onto the Charging Dock, ensure the Charging Contact Points on Charging Dock and the bottom of robot are contact well. The robot will start charging after hearing “in charging”. Battery fully charged may cost around 4.5h. Tips: 1. The robot can’t power on when in low battery.
④. Download and Install APP (1) Download and install app (2) Reset Wi-Fi Download APP by scanning below QR code. Press the key “ ” for 5S, and you will hear voice prompt "Reset WI-FI, enter network configuration mode", and the blue Wi-Fi indicator will flash rapidly, which means the robot start entering network configuration mode. (3) Add device Enter the home page of APP, click "+" in the upper right corner and add device according to the APP prompt.
⑤.Clean Mode (1) Auto Cleaning Method 1: Power on robot, after the startup music, press button on panel, auto cleaning will start. Method 2: Click the “Start cleaning” button thru APP to start cleaning (press the pause button to pause the current task). Reminder: If power is less than 20%, Robot will not be able to carry out cleaning task, please charge it before next cleaning. If power is less than 20% during cleaning, the robot will dock to charging base.
(3) Schedule Cleaning Schedule cleaning can be set thru APP. The robot will automatically start cleaning at the specified time you set and return to the charging base after cleaning. (4) Smart Area 1.Area cleaning After Smart Map generated successfully, the user can divide the map into different areas according the cleaning needs. You can set one or more cleaning C areas. Select the areas to clean after setting, the robot will only clean the selected area, and do not clean other areas. 2.
• The boundary area may be invalidated due to moving the charging base or furniture. So please do not to move or interfere the robot during cleaning. Due to APP updating, the functions and details may have some changes, please refer to the actual version. (5) Docking Mode Auto mode:When the battery power is low, Robot will prompt “Low power, start docking mode”, and start finding charging base to recharge.
4.Product Maintenance Tip: Before maintenance of the robot and spare parts, please turn off the main switch at the bottom. ①.Dust Bin Press Bin Release Button to remove dust bin and clean it. Tip: Please empty the dust bin after each usage.
②.Filters (1)Take the filters out from the Dust Bin. (2)Clean the Dust Bin and filters with provided Cleaning Tool. (3)Put the filters back together in the Dust Bin. Tip: Clean the filter once a week and replace it every 2 months.
③. Rolling Brush Remove brush cover, take out the rolling brush, clean the vacuuming aisle by a cloth. If the rolling brush has hairs winded, please cut them down with the knife on cleaning tool.
④.Side Brush ⑤.Swivel Wheel Pull out the side brushes, use the knife on cleaning Clean the swivel wheel with a cloth. tool to cut winded hairs, and then use cloth to clean it. Tip: Please clean the rolling brush and side brushes once a week, change the side brush every 3 months, and change the rolling brush every 6 months.
⑥.Cliff sensor Use a dry cloth to clean cliff sensors to ensure the sensitivity.
5.Troubleshooting No. 1 Problems Robot cannot Causes Ensure the charging cord is plugged into the dock and wall outlet, and the light on the Charging Dock is white. The poor connection of the charging contact points. Clean the charging connection points on both Charging Dock and bottom of the Robot with dry cloth. Get stuck by objects. Pick up objects like clothing, scraps of paper, power cords, and fragile objects to avoid Robot stuck before it starts working. Get stuck under furniture.
5 6 The left / right wheel may be entangled. Check left / right wheel for entanglement and clean the side wheel. abnormal Weak suction The Dust Bin is full Empty Dust Bin Filter clogged or wet Clean and dry the filter or replace it with a new one. The Main Power Switch on the bottom of Robot is off Turn on the Main Power Switch at the bottom of Robot. Left / right wheel Cannot schedule cleaning 7 Power is too low to start cleaning Charge Robot. The scheduled time have been set incorrectly.
6.Specifications A90 Robotic Vacuum Cleaner Charging Dock Robot Vacuum Dimensions 325*325*80mm Dimensions 170*137*95mm Battery 2600mAH Adapter Input Voltage AC 100-240V Wireless connection 2.4GHz Wi-Fi Rated Output 19V/600mA Rated Frequency 50/60Hz Rated Power 28W Rated Voltage 14.4V Charging Time 5H Working Hours 120min / / / 7.Amarey Customer Care +86-400-676-0068 service_cn@iamarey.com www.iamarey.cn Manufacturer: Shenzhen Ankobot Robot Co.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.