Installation Guide

1 2 3
54 6 7
Camera Overview
Quick Setup
Apollo
Wi-Fi LED
(Green)
Power LED
(Blue)
1080p
Resolution
Light Sensor
PIR Sensor
6 Flash LEDs
(Intruder Warning Light)
8 IR LEDs
(Night Vision)
WPS
Reset
Micro USB
Power Port
microSD Port
Get the App
Power on the Device
5V/2A
Adapter
Connect the Micro USB into the camera and plug
the power adapter into the power outlet. Apollo
is ready for app setup when the Power LED (Blue)
begins to flash.
Camera Setup in the App
Select Apollo in the app, then follow the instructions.
★ Please refer to the Tips & How To Page for more
info on how to share viewer or admin access to
other smartphone devices.
Connect Camera to the Internet
1. Please make sure that
your smartphone is
connected to the same
Wi-Fi SSID network.
(2.4 GHz (802.11 b/g/n)
is required).
2. For Android users, select
Auto-Detection. For iOS
users, refer to the QR code
setup in the app.
Select AMID to Complete Setup
Note: The AMID can be found at the bottom
of the device. Make sure the camera's AMID
is the same one in the app setup.
xxxxxx
Tap on the AMID to complete auto setup.
App Setup Complete
Congratulations!
Your Apollo is set up and ready to go. The Wi-Fi
LED indicator will be a solid green when the Internet
connection is successful.
Mount Your Camera
1. Use the provided
bracket for wall
or ceiling camera
installation.
2. There are 4 snap locks located at the bottom of
the device. Once locked in place, secure with the
screws.
3. Loosen the screws to adjust the angle. Be sure to
tighten the screws to secure your camera once it
has been oriented properly.
1
2
3
Screw
insert
Screw
Snap
lock
Wall
Ceiling
Ceiling
Wall
Use QR Code to Set up Device
1. Make sure your
camera and
smartphone
are parallel to
each other.
2. Your phone must be connected to the same
Wi-Fi router as your camera.
3. The QR code will be generated when you enter
your Wi-Fi password.
4. Show the QR code to the camera. You will hear
a beep when the QR code is read.
15~30cm
LED Indicator
Power
Indicator
(Blue)
Wi-Fi
Indicator
(Green)
Factory Reset
1. Ensure your camera is
powered on.
2. Wait for the camera's bootup
rotation to finish.
3. Using a paperclip or pin, press
the Factory Reset Button and
hold until you hear a beep.
4. Reset will take up to 25 seconds.
The Blue LED indicator will begin to flash when
the reset is complete.
Factory Reset
Button
Safety Guidelines
We designed Apollo to be
durable and easy to
use. Here are some
safety guidelines for you
to follow while using your
Amaryllo camera.
1. Avoid placing the camera under direct sunlight
2. Only use the provided power adapter and cable
for your camera (5V2A).
3. Use Apollo within its operating temperature 32°
to 95°F (0° to 35°C).
Need Help?
To find troubleshooting
tips or to get support, scan
the QR code or visit:
www.amaryllo.us/support
All devices come with a
limited one year warranty!
Scan the QR code to take
you to Amaryllo's legal page:
www.amaryllo.us/terms
Or if you need additional help, just contact us!
E-mail: [e-mail]
Phone: [phone] (toll-free)
Download the
free Amaryllo
app to get
started.
Power Indicator (Blue LED)
Solid Blue LED: Device is powered on.
Blinking Blue LED:
1. Camera is being accessed
remotely.
2. Camera is waiting for setup.
Wi-Fi Indicator (Green LED)
Blinking Green LED:
Camera is attempting to
connect to the Wi-Fi network.
Solid Green LED: Device has
connected a Wi-Fi AP router.
2.4 GHz (802.11 b/g/n)