IN400 AV SWITCHING AMPLIFIER INSTALLATION AND OPERATION MANUAL
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. LISEZ ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS The Innovation series from AMAV is a huge step forward in the interfacing and management of audio and visual sources. Integrating a host of smart, high end features in a compact package that offers the end user extremely simple control over their complex audio visual system. The Innovation series is as ground breaking as it is simple to operate. The IN400 is a compact AV switching amplifier with a host of extra features available to the AV integrator.
FRONT PANEL 6 8 4 5 7 3 2 1 1 MASTER VOLUME This pot controls the audio output level. 2 MASTER VOLUME LEDS These LED’s indicate the position of the volume control. They do not indicate the strength of the signal. 3 SOURCE SELECT SWITCHES These switches select the input that is routed to the audio and video outputs. 4 SOURCE SELECT LEDS The LED above the switch indicates when the channel is being routed to the outputs. LED State 1.
REAR PANEL 4 11 1 2 3 5 6 10 9 1 AUDIO INPUT Sources These are the RCA unbalanced line level audio inputs for each of the 8 sources. The top RCA connector is the left channel, bottom RCA connector is the right channel. 7 8 7 VGA INPUT These are high densisty 15pin D connector VGA inputs for the PC1/PC2/AUX3/ AUX4 sources. 8 VGA OUTPUT 2 MIX IN This input is not switched but mixes with the selected audio source. The bass/ treble/volume controls do not affect this input.
SETUP RS485 Settings Word Structure RS485 Setup Baud Rate: No. of Bits: Stop Bit: Parity Bit: ! - Start byte XXX - 3 byte command : - delimiter XXX - 3 byte data - carriage return All bytes are ASCII characters. The IN400 data port is an RS485 serial data port. Twisted pair cabling should be used when connecting RS485 devices, such as CAT3, CAT5, CAT5e or CAT6 UTP cabling. RS485 data networks should be wired in a ‘daisy chain’ configuration with a maximum of 32 devices in the chain.
INSTALLATION All installation work should be done with the power disconnected. The following inforamtion will help with installation. After installation is complete power up all the sources before turning on the IN400. POWER CONNECTION OUTPUT CONNECTIONS (cont.) Ensure the mains voltage supply matches the rear of the IN400 (+/- 10%) Video Video outputs are on either unbalanced RCA sockets (composite) or 15 pin high density female connectors D-connectors (VGA).
BLOCK DIAGRAM PAGE 8 IN400 INSTALLATION AND OPERATION MANUAL
DIMENSIONS IN400 INSTALLATION AND OPERATION MANUAL PAGE 9
SPECIFICATIONS POWER OUTPUT (0.5%THD, 1kHz) 8ohm 50W, 4ohm 80W THD (20-10kHz, 8ohm, -2dBr) Better than 0.1% Frequency Response(+/-3dB) 20-20kHz Gain 24dB @ 8ohm Line Audio THD Noise Floor Frequency Response(+/-3dB) Headroom Video VGA Video Video follows Audio switching Comms Type Baud Rate No of Data Bit Parity No of Stop Bits Power Consumption Thermal output SIZE (WXHXD) <0.
NOTES IN400 INSTALLATION AND OPERATION MANUAL PAGE 11
AUSTRALIA AND NEW ZEALAND www.australianmonitor.com.au SYDNEY MELBOURNE ADELAIDE AUCKLAND (NSW SALES) (VIC & TAS SALES) (SA & NT SALES) (NZ SALES) 1 Clyde Street Silverwater NSW 2128 Private Bag 149 Silverwater NSW 1811 Phone: (02) 9647 1411 Fax: (02) 9648 3698 Email: nsw@audiotelex.com.au 22/277 Middleborough Road Box Hill VIC 3128 PO Box 151 Blackburn South VIC 3130 Phone: (03) 9890 7477 Fax: (03) 9890 7977 Email: vic@audiotelex.com.
