Instruction Manual

ManualsBrandsAMAX INDUSTRIAL GROUP CHINA ManualsElectronicsPower Craze 1/18 High Speed Buggy

6. Install batteries into the remote control. Open the battery cover on

the bottom of the remote control (see diagram E). Insert 4 AA

batteries (not included) into the battery compartment, matching

polarity (+ and -) marked inside. Replace the battery cover.

CHARGING THE BATTERY

1. Insert the USB charger into the battery charging socket (see diagram A).

2. Connect the USB end of the cable to your computers USB port or a USB wall charger (see diagram B),

The Red CHARGE indicator light turns stay to show that charging is in progress.

3. Average charging time is approximately 2.5 hours( via 5.0V 2A USB wall charger). The truck

operates for approximately 40 minutes on full charge.

4. The red charging indicator turns green when the battery is fully charged.

Note: Periodically examine the charger for external damage. External damage to the charger may result

in the risk of fire, electric shock, or injury to persons. Never use a damaged adapter.

OPERATION

THIS IS A HIGH-SPEED OUTDOOR RC TRUCK. DO NOT PLAY INSIDE YOUR HOME OR OTHER SMALL ENCLOSED AREAS.

1. Turn your truck on:

• Pick up your truck and turn it over to make sure the battery is properly installed and the battery

compartment door is properly closed and locked.

• Sync your truck and remote control and set the truck on the ground.

2. Driving your truck:

• Pull the throttle to drive forward.

• Push the throttle forward to make truck move in reverse.

• Turn the steering control to the counterclockwise to turn the truck left. Turn steering to the clockwise to

turn the truck right.

• To break or quickly stop simply pull or push the throttle in the opposite direction and release the throttle.

Batteries Not Included (4xAA)

PACKAGE CONTENTS

• Radio Controlled OFF-ROAD RACER™

• Remote Control

• USB Charger

• 7.4V Li-poly Battery Pack

TRUCK DIAGRAM

REMOTE DIAGRAM

Your

truck

features an automatic 2.4G channel selection system that allows up to 8 people to race side

by side in the same wireless range.

For One Player:

1. Before starting, make sure that the power on both your remote control and truck are in the OFF

position. Make sure that there are no other 2.4G devices in the area.

2. Turn ON the truck and set it down on a flat surface.

3. Turn ON the remote control. When the remote control's power indicator flashes, pull the throttle all

the way down and the power indicator lights continuously. This indicates that your truck and

remote control have successfully synced. If pairing fails, repeat steps 1-3.

For Multiple Players:

1. Before starting, make sure that the power on all trucks and controllers are in the OFF position.

Make sure that there are no other 2.4G devices in the area.

2. Each person will have to sync a truck individually at a different time to avoid interference.

Follow steps 1 to 3 above, making sure to keep away from other people while also making sure that

no one else is syncing at the same time.

3. After syncing, leave the truck ON until all players have synced their trucks.

4. If there is interference, all players must turn off their controllers and trucks and restart the syncing

process.

SYNCING YOUR TRUCK

Steering

Throttle

ON/ OFF Switch

Power Indicator

Charging Light

WARNING

DO NOT USE TRUCK IN INCLIMATE WEATHER!

TROUBLESHOOTING

Before sending your truck in for repair, please check for a solution below.

Problem

Truck will not move.

Truck does not respond properly to

remote control.

Truck loses connection to remote

control.

Truck battery has fully charged, but

slower than normal.

Possible Cause(s)

Weak batteries; no batteries

Truck and remote not synced properly

Another RC truck may be transmitting on the

same radio frequency

Using truck in a small enclosed area

Using truck indoors

Low batteries in transmitter or vehicle

Driving truck for too long at high speeds, causing

motor to overheat

Solution

Install new batteries in remote control and

recharge the truck battery.

Refer to sync section and re-sync your truck

and remote.

Move to a new location where no other RC

trucks are present.

Move outdoors to a large open area.

Install new batteries in remote control or

recharge your truck.

Turn truck off for 10-15 minutes.

BATTERY WARNING:

• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (nickel-cadmium).

• Do not mix old and new batteries.

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the unit before being charged (if removable).

• Rechargeable batteries are only to be charged under adult supervision (if removable).

• Exhausted batteries are to be removed.

• The supply terminals are not to be short-circuited.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity.

LITHIUM BATTERY STATEMENT:

• Battery may explode or leak chemicals if opened, exposed to fire or high temperature, installed backwards,

or mixed with other battery types.

IMPORTANT: ALWAYS DISCONNECT CHARGER CORD AFTER CHARGING. NEVER LEAVE CHARGER CONNECTED TO

BATTERY OVERNIGHT OR FOR EXTENDED PERIODS OF TIME.

Head Lights

Tire

Fog Lights

5. Put the battery into the battery compartment then lock the

two ends with the battery locks.(see diagram c)

BATTERY LOCK