Amazfit GTS 2e User Guide Contents Amazfit GTS 2e User Guide......................................................................................................................... 1 Getting started............................................................................................................................................... 3 Appearance ................................................................................................................................... 3 Power on and off ....
Activities and health ................................................................................................................................... 17 PAI.............................................................................................................................................. 17 Activity goal ............................................................................................................................... 17 Idle alerts .................................................
Getting started Appearance Power on and off Power on: Press and hold the side button to power on the watch. The start screen will appear. If the start screen does not appear after you press and hold the digital crown, charge your watch and try again. Power off: When the device is on, press and hold the side button for 5 seconds to go to the power-off menu, where you can choose to shut down or restart the watch.
When measuring SpO2, avoid wearing the watch on the wrist joint, maintain a comfortable (appropriately tight) fit between the watch and the skin of your wrist, and keep your arm still throughout the measurement process. When affected by external factors (such as arm sag, arm sway, arm hair, and tattoo), measurement results may be inaccurate or the measurement may fail with no output. You can tighten the watch strap during the workout and loosen it afterwards.
Pairing with a new phone: 1. Open the Zepp app on your old phone and synchronize data with the watch. 2. On your old phone, go to the information page of the watch, tap More at the bottom of the page, and unpair the old phone from the watch. 3. Restore the factory settings of the watch, and then reboot the watch. After the watch is rebooted, pair the watch with your new phone as described in the initial pairing procedure.
Control center On the watch face page, swipe down to go to the control center for the following system features: Flashlight, Brightness adjustment, DND, Battery save mode, Screen locked, Find Phone, Theater mode, and Keep screen on. Time format Keep the watch connected to your phone. During data synchronization, the watch automatically follows the system time and time format of your phone, and displays the time in a 12-hour or 24-hour system.
Common operations Tap the screen Use this feature to select the current item or proceed with the next step. Press and hold your finger on the watch face Activate watch face selection and watch face settings. Cover the screen Unlit the screen. Swipe up/down/left/right Scroll or switch pages. On some pages, you can swipe right to return to the upper-level page. Press the side key Wake up the watch, go to the app list, or return to the watch face.
Features available when the watch is connected App alerts Keep the watch connected to your phone, and you can receive the phone app alerts on your watch. You can swipe up on the watch face page to view the latest 20 alerts in the notification center. Setting method: Keep the watch connected to your phone, open the Zepp app, go to Profile > Amazfit GTS 2e, and tap App Alerts to enable alerts for apps as needed.
Modifying settings on an Android phone: Keep the watch connected to your phone, open the Zepp app, and go to Profile > My Device > Amazfit GTS 2e > Notifications and Alerts > Incoming Call Alerts. Tap the "Please grant the phone permission" message on the top of the screen. In the Grant Phone Permission dialog box, grant the call permission to the Zepp app. If the message does not appear, the Zepp app has been assigned the phone permission.
2. Swipe left or right to preview the watch faces available. The Edit button will be displayed at the bottom of a watch face that supports compilations. You can tap this button to go to the page for editing the compilations of this watch face. 3. Select the compilation to edit, and tap this compilation, or swipe up and down on the screen to switch between compilations. 4. After editing, press the side button to enable the watch face.
2. Swipe left or right to preview the watch faces available to the watch, including built-in watch faces and synchronized online watch faces. 3. Tap the desired watch face to replace the current watch face. Delete watch faces When the storage space on the watch is running out, you will need to delete some of the watch faces to make room for new ones (some build-in watch faces cannot be deleted). 1. Wake up the watch face, and press and hold the watch face to go to the watch face selection page. 2.
You can also open the Zepp app and go to Profile > Amazfit GTS 2e > Shortcut Cards, where you can set the displayed content and the display order. Quick access apps Quick access apps shown on the right side of the watch face allow you to conveniently access watch features. You can add your frequently used apps and features, such as "Workout". Change quick access apps: 1. After waking up the watch, press the side button to open the app list.
Workout Workout The watch supports 12 workout modes, including outdoor running, walking, outdoor cycling, treadmill, indoor cycling, open water swimming, pool swimming, elliptical, climbing, trail running, skiing, and free training. Wake up the watch, press the side button to go to the app list, select Workout, and tap the workout mode you desire. Then tap GO on the workout preparation page to start recording workout data.
Workout alerts and settings At the bottom of the workout preparation page, you can tap the "Settings" icon to set the current workout mode. The related parameters vary depending on the workout mode. Workout goal: Set goal alerts for the target distance, target time, and target KCAL. Workout alert: Set alerts for the distance, safe BPM, BPM ranges, pace, and speed. Auto pause: The watch automatically detects the workout status.
Workout control Enable the workout app to run in the background: 1. During a workout, if you need to use other features, press the side button to return to the watch face page and perform other operations. The workout app will continue running in the background. 2. When the workout app runs in the background, the watch will continuously record the workout data and generate alerts based on the workout settings. 3.
View workout records View workout records on the watch: Wake up the watch, press the side button to go to the app list, and select Activities to view the latest 30 workout records. You can also select a record and view its details. View workout records on the phone: Synchronize the workout data to the Zepp app on the phone, and view the detailed workout records on the Workout records page.
Activities and health PAI PAI is used to measure a person's physiological activity and reflect overall physical condition. It is calculated based on a person's BPM, the intensity of daily activities, and physiological data. By maintaining a certain intensity of daily activities or workouts, you can obtain your PAI value. According to the results of the HUNT Fitness Study*, maintaining a PAI above 100 helps reduce the risk of cardiovascular death and increase life expectancy.
Idle alerts To encourage you to have a certain amount of activity every hour when you are awake and reduce the harm caused by sitting for too long, the watch monitors your activity as you wear it. If no activities are detected for more than one minute at the 50th minute of the current hour and you are wearing the watch correctly, the watch vibrates to remind you to work out.
Abnormal heartbeat alerts 1. Keep the watch connected to your phone, open the Zepp app, and go to Profile > Amazfit GTS 2e > Health Monitoring to enable the heart health monitoring feature. Then, the watch monitors your heart health and records BPM changes all day. 2. The watch vibrates when it detects abnormal heartbeats. 3. You can open the BPM app on the watch to view the day's abnormal heartbeat record, BPM curve, and BPM range. 4.
The watch vibrates when the measured BPM is greater than the predefined value and you have not done any detectable activity for the past 10 minutes. All day BPM monitoring 1. Keep the watch connected to your phone, open the Zepp app, and go to Profile > Amazfit GTS 2e > Health Monitoring to enable all day BPM monitoring and set the measuring frequency. Then, the watch automatically measures your BPM at the predefined frequency and records BPM changes all day. 2.
Sleep Sleep quality has an important impact on human health. When you sleep while wearing the watch, it automatically records your sleep data. Open the Sleep app to view your total sleep duration from the previous night and sleep data over the past seven days. You can also synchronize sleep data to the Zepp app to view your sleep duration, sleep stages, sleep score, and sleep suggestions.
SpO2 SpO2 is an important physiological parameter of respiration and circulation. 1. Wake up the watch, press the side button to go to the app list, and select the SpO2 app to start measuring SpO2. 2. When you are climbing a mountain, you can run the Workout app in the background, and start the SpO2 app to measure SpO2. 3. After measurement is complete, the watch displays the measurement result. You can also view measurement results for the whole day. Precautions for SpO2 measurement 1.
Stress The stress index is calculated based on changes in BPM variability. It is a reference for health status evaluation. You should rest more when the index is high. 1. Wake up the watch, press the side button to go to the app list, and swipe up and down to select the Stress app to view related information. 2. When automatic stress testing is enabled in the Stress app, stress will be measured every 5 minutes to show you the changes in your stress throughout the day.
Voice feature Offline voice Offline voice control allows you to speak to perform most of operations on the watch without connecting to a mobile phone. Offline voice wake-up mode: Go to Settings > User Preferences > Offline Voice Control > Wake Up Mode. 1. Respond in 5 seconds after you turn your wrist 2. Respond in 5 seconds after the screen lights on 3.
Offline voice commands: Go to Settings > User Preferences > Offline Voice Control > View All Voice Commands. There, you can see all offline voice commands the watch supports. Note: The global version of the watch supports the offline voice feature only when the system language is set to English. Music remote controller: Keep your watch connected to your phone.
App list management Keep the watch connected to your phone, open the Zepp app, and go to Profile > Amazfit GTS 2e > App List Management. Then you can set apps on the watch. Temperature The built-in watch sensor measures the real-time temperature of the contact position. For the most accurate temperature measurement, make sure the bottom shell of the watch is fully in contact with the object to measure for more than 30 minutes.
Weather You can check today's weather, wind, humidity, UVI intensity, and other information at any time, as well as the weather information for your current location for the next 7 days. The weather data needs to be synchronized through the mobile network. Therefore, you need to keep the watch connected to your phone to keep weather information up to date. You can also set the city and temperature unit (Celsius or Fahrenheit) in the Zepp app.
Barometer and Altimeter Barometer and Altimeter can show KPA and altitude information for your current location after positioning. After successful positioning, you watch displays the latitude and longitude. Alarm You can add alarms in the Zepp app and on the watch. Alarms can be repeated, enabled, or deleted. Press and hold alarms that are no longer needed to delete them. When the preset time for an alarm arrives, the watch will vibrate to remind you. You can choose to nap or turn it off.
Stopwatch The watch provides a stopwatch with an accuracy of 0.01 seconds and can record up to 24 hours. The watch can count up to 99 times during the timing.
Countdown You can set the countdown time. At the end of the countdown, the watch will vibrate. Watch settings System language settings Open the Zepp app and go to Profile > Amazfit GTS 2e > Watch Settings > System Language to change the system language of the watch. Wearing direction Go to Watch > App List > Settings > User Preferences > Wearing Direction, and set the button as either on the left or right of the screen based on how you wear the watch.