Antus Instructions for Use and Installation

ManualsBrandsAmba ManualsHome FurnishingAntus Collection A 2856 B 28" Towel Warmer with 32 Wide Bars, Digital Heat Controller and 1807 BTU in Brushed

Instructions for Use & Installation

ANTUS COLLECTION

CONSULT THIS INSTRUCTION MANUAL IN ITS ENTIRETY PRIOR TO

THE HANDLING & INSTALLATION OF ANY TOWEL WARMER

FOLLOW THE GENERAL GUIDELINES & INCLUDED WIRING DIAGRAM.

790 Pickens Industrial Dr,

Marietta, GA 30339 USA

Phone : (404) 350 9738

Fax : (404) 355 0166

www.ambaproducts.com

3165407

IP 54

SKU Width HEIGHT Power Amps BTU

A2056 19 3/4” 56 3/8” 400 watts 3.5 1364

A2072 19 3/4” 72 3/8” 530 watts 4.6 1807

A2856 27 1/2” 56 3/8” 530 watts 4.6 1807

ADDITIONAL COMPONENTS

1 – Plastic Anchor

2 – Cover Washer

3 – Regulating Plate

4 – Anchor Screw

5 – Supporting Screw

6 – Washer

7 – Cover

8 – Mounting Fixture

9 – Fixing Screw

10 – Extension (not shown - optional)

DIGITAL HEAT CONTROLLER

Please see Instructions

for Optional Switch see guide

110v

Summary of content (8 pages)

PAGE 1
IP 54 Instructions for Use & Installation 3165407 ANTUS COLLECTION SKU 110v Width HEIGHT Power Amps BTU A2056 19 3/4” 56 3/8” 400 watts 3.5 1364 A2072 19 3/4” 72 3/8” 530 watts 4.6 1807 A2856 27 1/2” 56 3/8” 530 watts 4.
PAGE 2
IMPORTANT INSTRUCTIONS WARNINGS & PRECAUTIONS BEFORE INSTALLING THE TOWEL WARMER CAREFULLY READ ALL INSTRUCTIONS Ensure that VOLTAGE (V) & FREQUENCY (HZ) indicated in the serial number plate correspond to the voltage & frequency available in the place of installation At receipt of goods, ensure that packaging is intact: ANY DAMAGES THAT OCCUR DURING TRANSPORT ARE NOT COVERED BY THE WARRANTY • • • • • • This heater is hot when in use — to avoid burns do not let bare skin touch hot surfaces For indoor use
PAGE 3
MAINTENANCE UPKEEP & CARE • • • • • Before any maintenance operation ensure that the power source is disconnected and that the switch is in the off position Before any maintenance wait for the unit to cool down completely Clean the outside surface with a soft cloth and liquid detergent or stainless steel cleaner Do not use abrasive cleaning or scouring products To maintain the delicate external finishes use the following methods with each finish: • • • • • Brushed finishes: rub the soft cloth following t
PAGE 4
INSTALLATION CAUTION: INSTRUCTIONS DO NOT TAKE OFF THE PROTECTIVE P.V.C. TAPE BEFORE INSTALLING TOWEL WARMER TO AVOID SCRATCHING, MARKING OR GRAZING THE SURFACE.
PAGE 5
INSTALLATION STEP 7 INSTRUCTIONS View Without Extension View With Extension • • Proceed with the fastening of the wall bracket to the bar by screwing the fixing screw (9); Repeat this procedure for the other wall brackets; CAUTION: REMOVE THE PROTECTIVE P.V.C. TAPE BEFORE SWITCHING THE TOWEL WARMER ON www.ambaproducts.
PAGE 6
IMPORTANT INSTRUCTIONS WARNINGS & PRECAUTIONS DIGITAL HEAT CONTROLLER All EMMESTEEL electric models can be integrated with the Digital heat Controller Manages the power supply to offer 9 different heat levels at a maximum power load of 1200w The DHC control system is certified and ratified according to American and European norms for electric devices, made of components that meets the requirements of current safety regulations.
PAGE 7
DIGITAL HEAT CONTROLLER (DHC) INSTALLATION STEP 1 INSTRUCTIONS E - Ground faston POWER REGULATOR B - DHC Supply Cable D - Towel Warmer cable A - Power Source Cable C - DHC Output cable 1 Connect T1 (A)-T2(B)-T3(D) to faston T(E) 2 Connect L 1 (A)-L2(B) 3 Connect N 1 (A)-N2(8) 4 Connect N3(0)-N4(C) 5 Connect L3(0)-L4(C) STEP 2 Level Settings: 1 — Minimum Heat 9 — Maximum Heat Can be wired in conjunction with a programmable timer. (CONSULT ELECTRICIAN) www.ambaproducts.
PAGE 8
SWITCH INSTALLATION FOR UNITS WITHOUT DIGITAL HEAT CONTROLLER COMPONENTS Power source cable Towel warmer cable • • • • Connect the two grounding cables (green) Consider the button as 2 separate vertical sections, one on the right and one on the left Connect the fastenings of the power source cable to one section, it doesn’t matter which Connect the fastenings of the towel warmer’s cable to the other section See the example below Fastening Connections (Step 2) FASTENING CONNECTIONS • Connect one ca