User manual

ManualsBrandsAmbient Weather ManualsConsumer electronicsWS-14

Ambient Weather WS-14 Wireless 8-Channel Floating Pool

and Spa Thermometer with Daily Min/Max Display User

Manual

Table of Contents

1 Introduction ..................................................................................................................................... 2

2 Getting Started ................................................................................................................................ 2

2.1 Parts List ....................................................................................................................................... 2

2.2 Floating Pool and Spa Thermometer Sensor Set Up ..................................................................... 2

3 Maintenance .................................................................................................................................... 7

4 Display Console Set Up .................................................................................................................. 7

4.1 Display Console Layout ..................................................................................................... 9

4.2 Sensor Operation Verification ................................................................................................... 9

5 Display Features .............................................................................................................................. 9

5.1 Console Operation............................................................................................................................. 9

5.1.1 Set Mode .................................................................................................................................... 9

5.1.2 Viewing the High and Low Alarms ...................................................................................... 10

5.1.3 Alarm Defaults ..................................................................................................................... 10

5.1.4 Setting the Min and Max Alarm ....................................................................................... 10

5.2 Manually Reset Max/Min ........................................................................................................... 10

5.3 Channel Selection ....................................................................................................................... 11

5.4 Sensor Search Mode .................................................................................................................... 11

5.5 Best Practices for Wireless Communication ............................................................................... 11

5.6 Adjustment or Calibration ........................................................................................................... 11

5.6.1 Remote Sensor Temperature Calibration.............................................................................. 12

5.6.2 Indoor Temperature Calibration ........................................................................................... 12

6 Glossary of Terms ......................................................................................................................... 13

7 Specifications ................................................................................................................................ 13

7.1 Wireless Specifications ............................................................................................................... 13

7.2 Measurement Specifications ....................................................................................................... 13

7.3 Power Consumption .................................................................................................................... 13

8 Troubleshooting Guide .................................................................................................................. 13

9 Accessories ................................................................................................................................... 15

10 Liability Disclaimer .................................................................................................................. 15

11 FCC Statement .......................................................................................................................... 15

12 Warranty Information ............................................................................................................... 16

Summary of content (17 pages)

PAGE 1
Ambient Weather WS-14 Wireless 8-Channel Floating Pool and Spa Thermometer with Daily Min/Max Display User Manual Table of Contents 1 2 Introduction ..................................................................................................................................... 2 Getting Started ................................................................................................................................ 2 2.1 Parts List ...............................................................
PAGE 2
1 Introduction Thank you for your purchase of the Ambient Weather WS-14 Wireless 8-Channel Floating Pool and Spa Thermometer with Daily Min/Max Display. The following user guide provides step by step instructions for installation, operation and troubleshooting. To download the latest manual and additional troubleshooting tips, please visit the FAQ website: http://ambientweather.wikispaces.
PAGE 3
Figure 1 1. To insert the batteries,, (1) Twist the KEY lid to unlock, (2) remove the key, and (3) twist the main body of the sensor by removing the lid, as shown in Figure 2 . Figure 2 2. The floating thermometer includes dip switches for assigning channel numbers. BEFORE inserting the batteries, locate the dip switches on the inside cover of the lid of the transmitter. Figure 4 displays all four switches in the OFF position (factory default setting).
PAGE 4
Figure 3 Figure 4 Channel Number: The WS-14 supports up to eight transmitters. To set each channel number (the default is Channel 1), change Dip Switches 1, 2 and 3, as referenced in Table 1. Temperature Units of Measure: To change the transmitter display units of measure (°F vs. °C), change Dip Switch 4, as referenced in Table 1.
PAGE 5
3. Reference Figure 5. Install 4 x AAA batteries. Figure 5 (1) Open the battery compartment and (2) insert 4 x AAA batteries into the battery compartment, observing the correct battery polarity. 4. After inserting the batteries, the remote sensor LED indicator will light for 4 seconds, and then flash once per 60 seconds thereafter. Each time it flashes, the sensor is transmitting data. 5. Verify the correct channel number (CH) and temperature units of measure (°F vs.
PAGE 6
(2) temperature units (°F vs. °C) (3) channel number 6. Close the battery door. Make sure both red colored gaskets are properly seated in their traces prior to closing the battery door, as shown in Figure 7. Failure to properly seal the floating thermometer will result in water leakage and damage. Figure 7 7. To close the lid, (1) Twist the lid until it is firmly locked and the key is aligned. (2) Insert the key and turn 90 degrees to lock the lid, as shown in Figure 8.
PAGE 7
Figure 9 Place the sensor in the water and make sure that it is within the effective transmission range from the display console. 3 Maintenance During each battery change (1-2 years), we recommend applying waterproof silicon grease to the seals: http://en.wikipedia.org/wiki/Silicone_grease Silicone grease is available at most hardware and pool stores.
PAGE 8
Figure 10 Fold out the desk stand, remove the battery cover, and insert three AAA (alkaline or lithium, avoid rechargeable) batteries in the back of the display console. All of the LCD segments will light up for a few seconds (to verify all segments are operating properly). 1. Replace the battery door, and place the console in the upright position with the desk stand folded out. The console will instantly display time, indoor temperature as designated by the icon.
PAGE 9
4.1 Display Console Layout Figure 11 4.2 Sensor Operation Verification Verify the indoor and outdoor temperature match closely with the console and sensor array in the same location (about 5 to 10’ apart). The sensors should be within 2°F (the accuracy is ± 1°F). Allow about 30 minutes for both sensors to stabilize. The temperature can be adjusted or calibrated later to match each other or a known source. 5 Display Features 5.
PAGE 10
4. Alarm Hour. Press the [+] or [-] key to increase or decrease the alarm hour. While the alarm value is flashing, press and hold the SET button for three seconds to toggle the alarm on and off the alarm. The time alarm icon will appear when set, and disappear when disabled. Press (do not hold) the SET key to advance to the next setting. 5. Alarm Minute. Press the [+] or [-] key to increase or decrease the alarm minute.
PAGE 11
Press the MIN/MAX button again to return to normal mode. To reset the Max/Min values, press and hold the MIN/MAX- button for 3 seconds. 5.3 Channel Selection Press the CH/+ button to switch the display between remote sensors 1 through 8, and scroll mode . In scroll mode, all of detected outdoor sensors will be displayed in five second intervals. 5.4 Sensor Search Mode If any of the sensor communication is lost, dashes (--.-) will be displayed on the screen. To reacquire the signal: 1.
PAGE 12
The purpose of your weather station is to measure conditions of your surroundings, which vary significantly from location to location. 5.6.1 Remote Sensor Temperature Calibration Prior to entering the calibration mode, press the CH/+ button to select the remote temperature sensor you wish to adjust. To enter the temperature calibration mode, press and hold the SET and CH/+ buttons at the same time for 5 seconds and the remote temperature value will begin flashing.
PAGE 13
6 Glossary of Terms Term Definition Accuracy is defined as the ability of a measurement to match the actual value of the quantity being measured. A hygrometer is a device that measures relative humidity. Relative humidity is a term used to describe the amount or percentage of water vapor that exists in air. Range is defined as the amount or extent a value can be measured. Accuracy Hygrometer Range 7 Specifications 7.
PAGE 14
Problem Solution The maximum line of sight communication range is 300’ and 100’ under most conditions. Move the sensor assembly closer to the display console. If the sensor assembly is too close (less than 5’), move the sensor assembly away from the display console. Make sure the remote sensor LCD display is working and the transmitter light is flashing once per 60 seconds. Install a fresh set of batteries in the remote thermo-hygrometer. For cold weather environments, install lithium batteries.
PAGE 15
9 Accessories The following software and hardware accessories are available for this weather station at www.AmbientWeather.com .
PAGE 16
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.21: Modifications not expressly approved by this company could void the user's authority to operate the equipment. Statement according to FCC part 15.