Instruction manual

ManualsBrandsAmbirad ManualsGas HeaterQUARTZ GLOW

AMBIRAD QUARTZ GLOW

INSTANT INFRA-RED HEATERS

INSTALLATION AND OPERATING MANUAL

INDEX Section

Introduction and Document Index

Installation Requirements ------------------------------------------------- 1

Assembly Instructions ----------------------------------------------------- 2

Commissioning Instructions ---------------------------------------------- 3

Servicing Instructions ------------------------------------------------------ 4

Spare Parts ------------------------------------------------------------------ 5

Fault Finding Guide -------------------------------------------------------- 6

Replacing Parts ------------------------------------------------------------- 7

User and Operating Instructions ---------------------------------------- 8

WARNINGS

AmbiRad equipment must be installed and maintained in accordance with the relevant

codes and practices. Due account should also be taken of any obligations arising from the

Health and Safety at Works Act 1974 or relevant codes of practice. In addition the

installation must be carried out in accordance with the current IEE wiring regulations (BS

7671), BS 6896 (Industrial & Commercial) and any other relevant British Standards and

Codes of Practice by a qualified installer. All external wiring MUST comply with the current

IEE wiring regulations.

Instruction Manual

Part No. 700505

Summary of content (20 pages)

PAGE 1
Instruction Manual AMBIRAD QUARTZ GLOW INSTANT INFRA-RED HEATERS INSTALLATION AND OPERATING MANUAL INDEX Section Introduction and Document Index Installation Requirements ------------------------------------------------- 1 Assembly Instructions ----------------------------------------------------- 2 Commissioning Instructions ---------------------------------------------- 3 Servicing Instructions ------------------------------------------------------ 4 Spare Parts ---------------------------------------
PAGE 2
Introduction. Welcome to the range of high frequency infra-rad heaters. Local regulations may vary in the country of use and it is the installers responsibility to ensure that such regulations are satisfied All installation, assembly, commissioning and service procedures must be carried out by suitable qualified competent persons to the statutory regulations in the country of use.
PAGE 3
1. Installation Requirements. Isolate any electrical supply to the heater and controller before proceeding. 1.1 Health and Safety AmbiRad heaters must be installed in accordance with the relevant codes and practices. Due account should also be taken of any obligations arising from the Health and Safety at Works Act 1974 or relevant codes of practice.
PAGE 4
AmbiRad Apollo Range AmbiRad Sorrento Range AmbiRad Titan Range Single Unit 1.3 Mounting the unit Wall Mounted Wall Mounted Ceiling Hung Wall Mounted Ceiling Hung 8 8 8 8 8 9 9 9 8 8 8 9 9 8 n/a n/a n/a n/a AmbiRad Sorrento SOR –DL30 Horiz AmbiRad Sorrento SOR –TW45 Horiz n/a n/a AmbiRad Sorrento SOR -15 AmbiRad Titan Range Horiz Horiz or Vertical Three Units Joined Ceiling Hung 91 9 9 9 AmbiRad Apollo Range Two Units Joined Horiz or Vertical Horiz or Vertical 1.
PAGE 5
1.3.1 Apollo range: 1.3.2 Sorrento range: • 1.3.2.1 General The heater must be mounted in such a way that the halogen lamp does not slant more than 4° from the horizontal, when viewed from the front. • The heater is suitable for installation only on a normally non-flammable surface. Observe the minimum safe distance between the heater body and inflammable surfaces when mounting. • Do not position the heater near to furniture or curtains as this could present a fire hazard.
PAGE 6
1. When wall mounting, securely fasten the Lshaped wall brackets to the mounting surface using both of the fixing holes in the short part of the bracket . Refer to Table 1 for recommended positioning of the heater. Please note. Wall fixings are not supplied. They should be selected to substantially support the weight of the installation. If in doubt contact a professional for advice 2.
PAGE 7
• When hanging from a ceiling two chains of equal length and gauge are required and should be selected with fixings that are more than adequate to hold the weight of the heater. Ensure minimum distance from ceiling is adhered to as shown below. If in doubt contact a professional for advice! 1. Fix the heater assembly to the chains via the hole in the centre of the joining bar as shown below and ensure the heater faces directly down when hanging.
PAGE 8
2. 3. 4. 5. of the heater. Please note. wall fixings are not supplied. They should be selected to substantially support the weight of the installation. If in doubt contact a professional for advice! Fix the heater assembly to the brackets via the bolt threads on the middle heater. A serrated washer should be placed on the threads first and the wall brackets should prise apart in order to fit the threads in place. Place a washer and a nut on the thread on the outside of the wall brackets – both sides.
PAGE 9
1.4 Electrical Connections 1.4.1 General • Warning - this appliance must be connected to an earthed supply. • Pre-wired heaters are either fitted with 2.5 metres of supply cable or 3.0 meters of supply cord and a moulded 13A plug therefore it is unnecessary to remove the terminal box in order to carry out normal installation of these models. • All unwired versions should be installed by a suitably qualified electrician, following the instructions herewith.
PAGE 10
2. Use a minimum of 1.0mm2 H05RN-F supply cable with 2 poles and earth and sleeve with silicon glass fibre braided (250°C) sleeving. The live and neutral wires must be connected to the terminal block. See below. 3. The green/yellow wire should be connected to the clamp marked with the earth symbol using a suitable wire terminal. Fit cord grip and terminal box saddle once wired. 4. Tighten the barrel nut of the compression gland so that the rubber seal grips the cable. 5.
PAGE 11
1.5 Technical Details. Table 1 Model ref Description Voltage Lamps x Power Total Power Current per lamp Amps per phase V ph kW kW a a Single tube 230V 1ph 1 x 1.5 1.5 6.5 6.5 QH 30-1 Double tube 230V 1ph 2 x 1.5 3.0 6.5 13.0 QH 45-1 Triple tube 230V 1ph 3 x 1.5 4.5 6.5 19.6 QH 45-3 Triple tube 415V 3ph** 3 x 1.5 4.5 6.5 6.5 QHL 30-1 Double linear 230V 1ph 2 x 1.5 3.0 6.5 13.0 QHL 45-1 Triple linear 230V 1ph 3 x 1.5 4.5 6.5 19.
PAGE 12
2. Assembly Instructions. PLEASE READ this section prior assembly to familiarise yourself with components and tools you require at various stages of assembly. Carefully open packaging and check the contents against parts and check list. to the the the the The manufacturer reserves the right to alter specifications without prior notice. 2.1 Please ensure that all packaging is disposed of in a safe environmentally friendly way.
PAGE 13
2.4.2 Titan Mobile heater The support stand for the Titan Static heater is supplied in two halves for ease of packing. 1. Interlock the two base plates with the base anchor plate uppermost. 2. Affix the casters to each of the four ends. 3. Join the support to the anchor plate and bolt trough the base pieces. 4. Affix the head anchor bracket to the top of the support. 5. Attach the heater head to the top of the support. Typical multiple heater assembly 2.4 Titan range: 2.4.
PAGE 14
3. Servicing Instructions. These appliances should be serviced annually by a competent person to ensure safe and efficient operation. In exceptional dusty or polluted conditions more frequent servicing may be required. The manufacturer offers a maintenance service. Details available on request 3.1 Tools Required. Suitable alternative tools may be used. The following tools and equipment are advisable to complete the tasks laid out in this manual. Leather Faced Gloves 3.
PAGE 15
4. Replacing Parts. 4.1 Replacing the lamp - general 4. Remove the panels to expose the lamp connections (see below). It is very important that your replacement lamp is exactly the same as the one it was supplied with. Failure to fit the exact same type could cause the heater to fail or even become dangerous especially when used in an outdoor environment. Please contact AmbiRad to purchase your replacement lamp and state the model number of the heater you wish to fit the lamp to.
PAGE 16
4.3 Sorrento Range: 1. Ensure the heater and lamp are cool and the power supply is disconnected by removing the plugs from the socket outlet - both plugs must be removed even if only one lamp is to be replaced. 2. Remove the screws from the terminal box at the back of the lamp you wish to replace and lift off the lid - see below. 3. Disconnect the lamp from the connector blocks by unscrewing the screws highlighted above below and remove the white coloured lamp wires from the terminal block. 6.
PAGE 17
11. The lamp should now be removed from the heater as shown below. 5. Disconnect lamp leads from terminal plates, and remove lamp retaining clips (see diagram below). 12. Refit the new lamp in reverse order ensuring that no wires get trapped and all screws are fully tightened. 4.4 Titan range: 1. Disconnect from the power supply and remove the heater from wall fixings before attempting to replace any lamp. 2. Remove the guard by flexing one end. 3.
PAGE 18
Notes
PAGE 19
Notes
PAGE 20
Document reference number GB/QG/004/0414 Replaces GB/QG/004/0813 Technical Support: Tel: 01384 489 200 Fax: 01384 489 707 ambiradgroupsupport@tnb.com www.ambiradgroup.co.