AMC o ö PHONES o CCVT Integrated A~lfier CVTS030 H.O.M.E. AUTOMATION SERIES va.l.
A A CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUAUFIED SERVICE PERSONNEL. ATTENTION A' A AFIN DEV1TER UN CHOC ELECTRIQUE ET LES CONSEQUENCES GRAVES CUI POURRAIENT EN ~SUlTER, PARA REDUCIR EL RIESGO OE SACUDIDAS ELECTRICAS, NO DEBERA QUITARSE LA TAPA (NI PARTE POSTERIOR). CONSULTESE AL PERSONAL CAPACITADO PARA LAS REPARACIONES INTERNAS. TENTEZ PAS D'OUVRIR L'APPAREIL ET OE TauCHER AUX cor.
INTRODUCTION INSTAlLATION The AMC CVT 3030 has been designed to give superb sound quality and represents outstanding value for money. The CVT 3030 is a hybrid mosfet valve design, capable of giving superb sound reproduction. The components are all of the highest quality, but there are a few simple hints to follow in order to get the best from your new amplifier. 1) 00 not stand any object or other component on the top.
REAR PANEL CONNECTIONS/FRONT PANEL CONTROLS REAR PANEL 1 " PttCK) 1»" CZt ~ -..c _ L~ R -{()------1~o--,~ft_-ft-A 1. PHONO GROUND TERMINAL 2. PHONO MM INPUT 3. DATINPUT 4. CD INPUT 5. TUNER INPUT 6. VIDEO INPUT 7. AUXlUARY INPUT 8. TAPE INPUT 9. TAPE OUTPUT 10. LOUDSPEAKER TERMINALS 11. AC CONVENIENCE OUTLETS 12. AC UNE CORD FRONT PANEL AMC A~lfier H.O.M.E. AUTOMATION SERIES CCVT Integrated CVT3030 o VOLlIoE ••ss 1 2 3 1. POWER SWITCH 2. PHONES 3. PHONES/NORMAUDIRECT SWiTCH 4.
REAR PANEL CONNECTIONS DAT The DAT input is suitable for use with any DAT player. Connect your DAT player using the phono socket marked DAT. A/COUTLET The AlC convenience outlet is fitted so that other components can be powered when your amplifier is switched on. You must fit an European Standard two pin plug, avallable from most speciallst dealers. UNDER NO CIRCUMSTANCES SHOULD THE CASE OF THE AMPLIFIER BE OPENED BY ANYONE OTHER THAN A QUALIFIED ENGINEER, AS DANGEROUS VOLTAGES ARE PRESENT INSIDE.
FRONT, PANEL CONTROLS For 8 Ohm Speakers, connect the negative (black) speaker wire to the'common' negative binding post. Then connect the positive (red) cable to the 8 Ohm red binding post. Repeat for the right speaker. For 4 Ohm speakers, the negative (black) connections are the same as the 8 Ohm, but the positive or red connection must be to the 4 Ohm binding post.
level differences caused by the nature of the input signal or due to room acoustics. PLAYBACK Set the Tape Monitor switch to the 'Tape' position and your recorder to the playback mode. TONE CONTROLS The tone controls on your AMC amplifier use low colouration high overload margine (higher then 50V RMS.) circuitry to ensure the minimum degradation of the music signal. They are designed to gradually modify the tonal emphasis of the music and to compensate for such problems as difficult room acoustics.
SPECIFICATIONS Power output into 8/4 ohms ............................................................................................... 30W With both channels driven Rated T.H.D. 45Hz-20KHz ................................................................................................ 1.0% 1KHz clipping power into 8/4 ohms .................................................................................... 36W Input sensitivity for 1W/3OW into 8 ohms: High level inputs ..................................
SAFETY INSTRUCTION 1. READ INSTRUCTIONS All the safety and operating instructions should be read before the appliance is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the appliance and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5.
WEL TRONICS CORP. LON DON/L.A. C 1992 AMC PRINTED IN TAIWAN R.O.C.
