User's Manual

ManualsBrandsAmcrest Technologies ManualsCamera & PhotoPan/Tilt Video Baby Monitor (Camera Unit)

Setup

Camera Setup

Power Supply - Using AC Power

1.1

1. Plug one end of the provided power adapter into a wall outlet and the other

end into the back of the camera.

2. Press the ON/OFF button to turn on the camera. The LED (green light) on the camera

will light up.

Note : Press and hold the ON/OFF button for about 2 seconds to turn off

the camera.

1. Open the battery compartment cover on the rear of the monitor.

2. Insert the battery with the metal facing the battery compartment.

3. Close the battery compartment cover, and make sure it is locked securely.

4. Press the POWER button to turn on the monitor.

Monitor Setup

Power Supply

2.1

The monitor uses a Lithium-ion rechargeable battery, or the household power

adapter.

Loading the Battery

When Battery is in low level after loading the battery, the LED (greed light) will start

blinking and need to recharging.

1. Plug one end of the provided power adapter into a wall outlet and the other end

into the monitor.

2. The LED (red light) will light up when the battery is charging .

3. When battery is fully charged, the LED (red light) will turn off .

Battery Charging

Night Vision

1.2

The camera has eight high-intensity LEDs for picking up clear images in the dark.

When the light sensor detects low ambient light levels, the LEDs will be automatically

activated. Press the brightness up button and down button at the same time on

the monitor unit to enable/disable/auto the night vision function.

The on-screen-display (OSD) will notify you the night vision function is set to

ON/OFF/AUTO.

1. Plug one end of the provided power adapter into a wall outlet and the other end

into the monitor.

2. Press the POWER button and to turn on the monitor.

Note 1 : When power on the monitor, the LED (green light) will light up.

Note 2 : Press and hold the POWER button for about 2 seconds to turn off the

monitor.

Using AC Power

Summary of content (7 pages)

PAGE 1
Setup 1 Camera Setup 1.1 Power Supply - Using AC Power 1. Plug one end of the provided power adapter into a wall outlet and the other end into the back of the camera. 2. Press the ON/OFF button to turn on the camera. The LED (green light) on the camera will light up. Note : Press and hold the ON/OFF button for about 2 seconds to turn off the camera. 1.2 Night Vision The camera has eight high-intensity LEDs for picking up clear images in the dark.
PAGE 2
.2 Monitor Remote Control Function The monitor can control the movement of the camera. The camera head has the ability to rotate up, down, right and left. Press the up or down buttons on monitor to move the camera up or down. Press the left or right buttons on monitor to move the camera left or to the right. See Fig. 3. Tilt Pan Fig. 3 2.3 VOX ( Voice-Operated Transmission) function 1. Press the volume up button and down button at the same time on the monitor unit to enable/disable the VOX function.
PAGE 3
2.4 Volume Setting Press volume up or down Press to increase volume. Press to decrease volume. buttons to adjust volume level. 2.5 Brightness Setting (Brightness) Press brightness up or down Press to increase brightness. Press to decrease brightness. 3 buttons to adjust the brightness. Camera Paring The system comes with a camera unit that has already been paired with the monitor. The "Camera Paring" function gives each camera unit a separate channel on the monitor unit.
PAGE 4
Package Contents - One Camera One Monitor Two Power Adapters Lithium-ion Battery for Monitor User Manual Troubleshooting You don’t getting any signal - Make sure the camera and the monitor are turned on. - Make sure the power plugs are firmly installed and plugged in. If the signal is poor, or if there is interference - If there is a microwave oven use in the between the camera and monitor, remove the microwave oven or turn it off, it may be causing interference.
PAGE 5
FCC Statement WARNING : Modifications not authorized by the manufacturer may void users authority to operate this device. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
Following the safety tips To prevent deaths and injuries associated with baby monitor cords : - Make sure the camera unit and power adapter cable are always out of reach of the baby at least 3 feet (1 meter) away. Note : It's important even if your baby is not yet standing or mobile. Camera Unit - Never use extension cords with power adapters. Only use the power adapters provided.
PAGE 7
Power Adapter information Source 1 Model number Input Output S08-006-0060-00800 100 ~240 , 50 ~60 Hz, 0.2A 6V 800mA Source 2 Model number Input Output CS6D060080 100 ~240 , 50 ~60 Hz, 0.2A 6V 800mA Only use Power Adapter listed in the user manual. Battery information Model number Specification PT603450 3.7V 1000mAh Only use Battery listed in the user manual. CAUTION :Risk of explosion If battery is replaced by an incorrect type. Dispose of used battery according to the instructions.