UNO-2059E GX2-400 Universal Network Controller with PC Card, LAN, 2 x USB, 2 x RS-232/485, 2 x RS-232/422/485 User Manual
Copyright The documentation and the software included with this product are copyrighted 2006 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Contents Chapter 1 Overview .......................................................... 2 1.1 1.2 1.3 1.4 1.5 Chapter Chapter Introduction ....................................................................... 2 Hardware Specifications ................................................... 2 Safety Precautions ............................................................. 4 UNO-2059E Series............................................................ 4 Chassis Dimensions......................................
Figure A.6:RS-232 Jumper Settings ............................ 23 Figure A.7:RS-485 Jumper Settings ............................ 23 A.3 RS-232/422/485 Serial Port (CN15~CN16) ................... 23 A.4 Ethernet RJ-45 Connector (LAN1) ................................. 27 A.5 Phoenix Power Connector (CN1).................................... 27 A.6 A.7 5V Power Output Connector (CN2)................................ 27 PS/2 Keyboard & Mouse Connector (CN10).................. 28 A.
CHAPTER 1 2 Overview This chapter gives background information on the UNO-2059E. It shows you the UNO-2059E overview and specifications.
Chapter 1 Overview 1.1 Introduction Leveraging field-approved and worldwide-awareness real-time OS technology, Advantech UNO-2000 series provide Windows CE & XPe SP2 ready solution, and support several standard networking interfaces, such as Ethernet, Wireless LAN, RS-232/422/485 and so on. Because of its openness, great expansion capability and reliable design – fanless and diskless, Advantech UNO-2000 series are ideal embedded platforms to implement custom applications in diversified applications. 1.
- RS-422/485 speed: 50 ~ 921.6Kbps - RS-232 data signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND - RS-422 data signals: TxD+, TxD-, RxD+, RxD-, GND - RS-485 data signal: DATA+, DATA-, GND - RS-232 max data distance: 50 feet (15.2 meters) - RS-422/485 max data distance: 4000 feet (1220 meters) • USB Interface: Two USB ports, USB OpenHCI, Rev. 1.
1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. All of the connector pin assignments are shown in Appendix A. Warning! Always disconnect the power cord from your chassis whenever you are working on it. Do not connect while the power is on. A sudden rush of power can damage sensitive electronic components. Only experienced electronics personnel should open the chassis.
Common parts: • Warranty certificate • Software Supporting CD-ROM • 6P-6P-6P 20cm KB and PS/2 Mouse Y cable (P/N: 1700060202) • Plug-in Block 2P Female (P/N 1652002205) • 6P-15P 10cm VGA cable (P/N: 1703150101) • DIN-rail mounting accessory (1997001110, 1997001120, 1997001130, 1997001140) For UNO-2059ECE only: • Built in 128MB CompactFlash card with Windows CE .NET • End User License Agreement for Windows CE .
1.5 Chassis Dimensions Figure 1.
CHAPTER 2 2 Hardware Functionality This chapter shows how to set up the UNO-2059E’s hardware functions, including connecting peripherals, switches and indicators.
Chapter 2 Hardware Functionality 2.1 UNO-2059E Peripherals The following two figures show the connectors on UNO-2059E. The following sections give you detail information about function of each peripheral. Figure 2.1: UNO-2059E Front Panel Figure 2.2: UNO-2059E Rear Panel 2.2 COM1~COM2: RS-232/485 Interfaces The UNO-2059E offers two RS-232/485 serial communication interface ports, and they are COM1 and COM2.
2.3 COM3~COM4: RS-232/422/485 Interfaces The UNO-2059E offers two RS-232/422/485 serial communication interface port, and they are COM3 and COM4. Each port can be configured individually to either RS-232, RS422/485 by using on-board jumpers. (See Appendix A.3) and Table 2-2 lists the default setting of each port. Table 2.
2.4 LAN: Ethernet Connector The UNO-2059E is equipped with Realtek RTL8100BL Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Yellow LED) and Active (Green LED) status. 2.5 Power Connector The UNO-2059E comes with a Phoenix connector that carries 18~48 VDC external power input, and features reversed wiring protection.
2.9 PCMCIA: PC Card Slot The UNO-2059E provides one PC Card slot that supports CardBus (Card-32) Card and 16-bit (PCMCIA 2.1/JEIDA 4.2) Card standard. It supports +3.3 V, +5 V and +12 V @ 120 mA working voltage. PC Card is a 85.6 mm long by 54 mm wide (3.37" x 2.126") sized, 68-pin connector used and removable module standardized by PCMCIA that is known as “PCMCIA card.” PS: PCMCIA interrupt assignment is IRQ 9. 2.
LED and Buzzer Control Register LEDEn: Enable LED flickering LEDS0 and LEDS1: LED flickering speed setting bit SPKEn: Enable buzzer alarming SPKS0 & SPKS1: Buzzer alarming setting bit Table 2.4: Programmable LED Control Bit LED Flickering Status LEDS1 LEDS2 Light on 0 0 Fast flicker 0 1 Normal flicker 1 0 Short flicker 1 1 Table 2.5: Programmable Buzzer Control Bit Buzzer Alarm SPKS1 SPKS0 Beep on 0 0 Short beep 0 1 Normal beep 1 0 Long beep 1 1 2.
CHAPTER 3 2 Initial Setup This chapter shows how to initialize the UNO-2059E, sections include: Sections include: • Inserting the CompactFlash Card • Chassis grounding • Connecting the Power • BIOS Setup and System Assignments
Chapter 3 Initial Setup 3.1 Inserting CompactFlash Card The procedure for installing a CompactFlash card into the UNO-2059E is as follow, please follows these steps carefully. Step 1: Remove the power cord. Step 2: Unscrew four screws from the rear panel of the UNO-2059E. Step 3: Remove the rear panel. Step 4: Plug a CompactFlash card with user’s OS and application program into a CompactFlash card slot on board. Step 5: Screw back the rear panel with four screws. 3.
Connecting Chassis Ground with System Power Ground: (Default) JP1 Not Connecting Chassis Ground with System Power Ground: JP1 3.3 Connect the Power Connect the UNO-2059E to a 18~48 VDC power source. The power source can either be from a power adapter or an in-house power source. 3.4 BIOS Setup and System Assignments UNO-2059E adopts Advantech SOM-2354 CPU module.
UNO-2059E User Manual 16
APPENDIX A 2 Pin Assignments This appendix gives the UNO-2059E pin assignments Sections include: • Board Connectors & Jumpers • RS-232/485 Serial Port • RS-232/422/485 Serial Port • Ethernet RJ-45 Connector • Phoenix Power Connector • 5V Power Output Connector • PS/2 Keyboard and Mouse Connector • USB Connector • 6-pin Mini VGA Display Connector • CompactFlash Master/Slave Jumper • Enhanced IDE Connctor
Appendix A Pin Assignments A.1 Board Connectors & Jumpers There are connectors and jumpers on the UNO-2059E board. The following sections tell you how to configure the UNO-2059E hardware setting. Figure A-1 and figure A-2 show the locations of UNO-2059E connectors and jumpers. Figure A.1: Connector & Jumper Locations (Top) Figure A.
Table A.
A.2 RS-232/485 Serial Port (CN13~CN14) Pin Assignments 1 2 6 3 7 4 8 5 9 Table A.2: RS-232/485 Serial Port Pin Assigns Pin RS-232 Signal Name RS-485 Signal Name 1 DCD DATA- 2 RxD DATA+ 3 TxD NC 4 DTR NC 5 GND GND 6 DSR NC 7 RTS NC 8 CTS NC 9 RI NC Note: NC represents “No Connection.
Terminator Resistors Setup for RS-485 The terminal resistors for impedance matching on the UNO-2059E are not installed in the factory. Users can install the resistors with the appropriate resistances according to the UNO-2059E application. Each terminal resistor corresponds to a different channels for DATA+, DATA- lines.
RS-485 Signal Wiring The RS-485 standard supports half-duplex communication. This means that just two wires are needed to both transmit and receive data. Handshaking signals (such as RTS, Request To Send) in RS-232 are normally used to control the direction of the data flow and to switch the transmission accordingly. In RS-485 mode, the UNO-2059E automatically senses the direction of the data flow and switches the transmission direction - no handshaking is necessary.
Jumper Setting for RS-232 Interface: (Default Setting) A B C D E F G H Figure A.6: RS-232 Jumper Settings Jumper Setting for RS-485 Interface: A B C D E F G H Figure A.7: RS-485 Jumper Settings A.3 RS-232/422/485 Serial Port (CN15~CN16) Pin Assignments 1 2 6 3 7 4 8 5 9 Table A.
Terminator Resistor Setup for RS-422/485 The terminal resistors for impedance matching on the UNO-2059E are not installed in the factory. Users can install the resistors with the appropriate resistances according to the UNO-2059E application. Each terminal resistor responds to different channels for RS-422/485 signal lines.
An example of the installation of COM3 is as follows: TR3 120 Ω Figure A.9: Terminator Installation RS-232/422/485 Selection COM3 and COM4 support 9-wire RS-232, RS-422 or RS-485 interfaces, and you can set corresponding jumpers to select serial ports as RS-232 or RS-422/485 interfaces shown in Table A-7. The system detects RS-422 or RS-485 signals automatically in RS-422/ 485 mode. Table A.
RS-485 Auto Flow Control and RS-422 Master/Slave Mode Selection You set the “Auto Flow Control” mode of RS-485 or “Master/Slave” mode of RS-422 by using SW2 DIP switches for each RS-422/485 port. In RS-485, if the switch is set to “Auto”, the driver automatically senses the direction of the data flow and switches the direction of transmission. No handshaking is necessary. In RS-422, if DIP switch is set to “On,” the driver is always enabled, and always in high or low status. Table A.
A.4 Ethernet RJ-45 Connector (LAN1) Ethernet RJ-45 Connector Pin Assignments Table A.9: Ethernet RJ-45 Connector Pin Assigns Pin 10/100Base-T Signal Name 1 XMT+ 2 XMT- 3 RCV+ 4 NC 5 NC 6 RCV- 7 NC 8 NC A.5 Phoenix Power Connector (CN1) Phoenix Power Connector Pin Assignments Table A.10: Phoenix Power Connector Pin Assigns Pin Signal Name 1 18 ~ 48 VDC 2 GND A.
A.7 PS/2 Keyboard & Mouse Connector (CN10) PS/2 KB/MS Connector Pin Assignments 6 5 3 4 2 1 Table A.11: Keyboard & Mouse Pin Assigns Pin Signal Name 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MS CLOCK A.8 USB Connector (CN11, CN12) USB Connector Pin Assignments 4 3 2 1 Table A.
A.9 6-pin Mini VGA Display Connector (JP3) VGA Display Connector Pin Assignments PCB 1 2 3 4 5 6 Table A.13: VGA Display Connector Pin Assigns Pin Signal Name 1 RED 2 H-SYNC 3 GREEN 4 V-SYNC 5 BLUE 6 GND VGA Adaptor Cable Pin Assignments 5 1 10 6 15 11 Table A.
Chipset The UNO-2059E uses a AMD CS5535 chipset for its SVGA controller. It supports interlaced and non-interlaced analog monitors (color and monochrome VGA) in high-resolution modes while maintaining complete IBM VGA compatibility. Digital monitors (i.e. MDA, CGA and EGA) are NOT supported. Multiple frequency (multisync) monitors are handled as if they were analog monitors.
A.11 Enhanced IDE Connector (CN4) You can attach two IDE (Integrated Device Electronics) drives to the UNO-2059E for software installation or system testing. The UNO-2059E has an EIDE connector, designated CN1. Wire number 1 on the cable is red or blue, and the other wires are gray. Connect one end to connector CN1 on the board. Make sure that the red (or blue) wire corresponds to pin 1 on the connector (on the right side). See “A.
UNO-2059E User Manual 32
