Drum Sander EZ-8 Operator’s Manual
READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
EN DANGER: Failure to read the Owner’s Manual prior to operating or servicing your American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If you or your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine. DANGER: DANGER: DANGER: WARNING:: WARNING:: WARNING:: WARNING:: A.
EN 4
EN 5
EN Introduction Control Switch Operating Control Lever Dust Pipe Control Link Transport Handle Locking Collar Handle Latch Level Adjustment Model Abrasive Size Abrasive Rate Drum Rate Dust Control Rate Drum Pressure Leveling Controls Operating Controls Motor Power Cable Voltage Frequency Amperage Dimensions (in)* Weight (lbs) * * Shipping Value 07012A 8 in x 19 in sleeve 2830 ft/min 1800 RPM 76 CFM 25 lbs Externally Adjustable Lever Operated 1½ HPTEFC Thermally Protected 40’ 12 Gauge Abrasive Resis
EN Electrical Connection Instructions SAFETY INSTRUCTIONS This floor-finishing machine shall be grounded while in use to protect the operator from electrical shock. The machine is provided with a three-conductor cord and a three contact grounding attachment plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect this wire to other than the grounding pin of the attachment plug.
EN Machine Transportation Figure 1 Figure 2 Figure 4 Figure 3 8
EN Machine Set-up 9
EN Machine Setup This sanding machine is designed to be operated with a remote vacuum dust collection system or with the included dust bag. Preparing Remote Vacuum Dust Collection Systems 2" Hose from D A vacuum system (not included) To prepare the machine for remote vacuum dust collection systems that have a 2” hose end, follow this procedure: 1.5" Hose from vacuum system (not included) 1. Install 2” hose end (figure 1, A) directly over the exhaust tube (figure 1, B). 2.
EN Operating Instructions Figure 11 1 2 3 4 11
EN Adjustment Procedures Leveling To adjust the machine leveling follow this procedure: 1. Locate the leveling screw. See Figure 6. 2. Tighten the screw (compress the leveling spring) to sand heavier on drive belt side of sanding drum. 3. Loosen the leveling screw (relax the leveling spring) to sand heavier on the side opposite the drive belts. Condition - Pad creates ridges on both edges or a “hop” is experienced: Rotate both adjusting screws equal amounts clockwise.
EN Troubleshooting 13
ES LEA ESTE MANUAL Este manual contiene información importante acerca del uso y la seguridad de la máquina. Si no lee el manual antes de utilizar su máquina American Sanders o de intentar realizar los procedimientos de reparación o mantenimiento de la misma, usted o el resto del personal podrían sufrir lesiones; asimismo, podrían producirse daños a la máquina o a otras propiedades. Antes de utilizar la máquina, es necesario recibir la capacitación adecuada en la operación de la misma.
ES Instrucciones De Seguridad Para El Operador PELIGRO significa: ADVERTENCIA significa: PRECAUCIÓN significa: Usted u otras personas pueden estar expuestos a sufrir lesiones personales, inclusive la muerte si las indicaciones de PELIGRO que se encuentran en esta máquina o en el manual de instrucciones se ignoran o no se tienen en cuenta. Lea y respete todas las indicaciones de PELIGRO que se encuentran en el manual de instrucciones y en la máquina.
ES 16
ES Introducción Palanca de control de funcionamientor Interruptor de control Collarín de cierre Enlace de control Manija de transporte Collarín de cierre Tubo para aspiración de polvo Ajuste del nivel Modelo Tapa del tambor 07012A 07058A 07060A 07084A 07057A 20.3 x 48.2 la manga 20.3 x 48.2 la manga 20.3 x 48.2 la manga 20.3 x 48.2 la manga 20.3 x 48.
ES Instrucciones De Seguridad Esta máquina para pisos de acabado deberá estar conectado a tierra mientras esté en uso para proteger al operador de una descarga eléctrica. La máquina está provista de un cable de tres conductores y un accesorio de conexión a tierra de tres contactos de enchufe para adaptarse al receptáculo de conexión a tierra adecuada. El conductor verde (o verde y amarillo) en el cable es el cable a tierra. Nunca conecte este cable a otro que el pasador de puesta a tierra del enchufe.
ES Cómo transportar la máquina Figura 1 Figura 2 Figura 4 Figura 3 19
ES Instalación de la máquina Para instalar su máquina siga este procedimiento: 1. Familiarícese con la máquina y lea todas las indicaciones de peligro, advertencia y precaución. Asegúrese de que todos los operadores de la máquina hayan leído este manual de instrucciones. Si ellos no pueden leer este manual, explíqueles el mismo por completo antes de permitirles operar la lijadora. 2. Instale la manija y fije los seguros. Consulte la figura 6. 3.
ES Instalación de la máquina Esta lijadora está diseñada para utilizarse con un sistema colector de polvo remoto mediante vacío o con la bolsa de polvo incluida. Preparación de los sistemas colectores de polvo remotos mediante vacío MANGUERA DE 2" DEL SISTEMA DE ASPIRACIÓN (NO INCLUIDO) A D MANGUERA DE 1.
ES Operación de la máquina 22 1 2 3 4
ES Procedimientos de ajuste de la lijadora Nivelación Para nivelar la máquina: tome el tornillo de ajuste de la roldana pivotante “A” con una herramienta adecuada (pinzas, etc.). Usando una herramienta similar, afloje la tuerca de seguridad “B” mediante un movimiento en dirección contraria a las agujas del reloj. (Figura 6). Condición - La almohadilla crea salientes en los dos bordes o se experimenta un “salto”: Rote los tornillos de ajuste en igual medida en sentido de las agujas del reloj.
ES Resolución de problemas 24
FR LISEZ CE MANUEL Ce Manuel contient des informations importantes concernant l’utilisation et le fonctionnement de cette machine dans des conditions de sécurité optimales. La non-lecture de ce manuel avant d’utiliser ou d’entretenir votre machine American Sanders risque de provoquer un accident ou d’endommager la machine ou son environnement. Vous devez avoir été formé à l’utilisation de cette machine avant de l’utiliser.
FR Consignes De Securite Destinees A L’operateur DANGER signifie: AVERTISSEMENT signifie: MISE EN GARDE signifie: De graves blessures corporelles, voire la mort, peuvent survenir si les déclarations DANGER apposées sur l’appareil ou inscrites dans le Manuel de l’utilisateur sont ignorées ou ne sont pas suivies. Lisez et respectez toutes les consignes DANGER se trouvant dans le Manuel de l’utilisateur et sur l’appareil.
FR 27
FR Introduction Levier de commande Interrupteur Tuyau à poussières Tige de commande Poignée de transport Collier de blocage Verrou du manche Réglage du niveau Couvre-tambour Modèle 07012A 07058A 07060A 07084A 07057A Dimension de abrasif (cm) 20.3 x 48.2 cm 20.3 x 48.2 cm 20.3 x 48.2 cm 20.3 x 48.2 cm 20.3 x 48.
FR Consignes De Sécurité 29
FR Transport de l’appareil 30
FR Préparation de l’appareil Figure 5 Figure 6 Figure 7 Figure 8 31
FR Préparation de l’appareil D TUYAU DE 2" DU SYSTEME D’ASPIRATION (NON FOURNI) B TUYAU D’EVACUATION C TUYEAU DE 1.50" DU SYSTEME D’ASPIRATION (NON FOURNI) (30563A) TUYAU DE 2" X ADAPTATEUR DE TUYAU DE 1.
FR Utilisation de l’appareil Figure 11 1 2 3 4 33
FR Réglage de la ponceuse Mise à niveau Pour régler la mise à niveau de l’appareil, exécutez les opérations suivantes : 1. Repérez la vis de mise à niveau (voir la figure 6). 2. Serrez la vis (en comprimant le ressort de mise à niveau) si vous désirez poncer plus fort sur le côté du tambour adjacent à la courroie d’entraînement. 3. Desserrez la vis (en relâchant le ressort de mise à niveau) si vous désirez poncer plus fort sur le côté du tambour opposé à la courroie d’entraînement. .
FR Dépannage 35
Drum Sander FloorCrafter BeltEZ-8 Sander Operator’s Manual Parts Manual Notes: ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ______________________________________
EZ-8 Sander Section II Parts Manual
HANDLE ASSEMBLY (07012A, 07058A, 07057A, 07084A) HANDLE ASSEMBLY (07012A, 07058A, 07057A, 07084A) 37 21 38 44 22 43 27 41 9 40 39 10 34 42 29 24 13 28 42 45 5 2 26 20 12 17 17 11 35 18 16 30 18 15 16 18 8 33 31 23 19 7 36 34 3 14 32 1 4 RF059800 25 032117 38
HANDLE ASSEMBLY (07012A, 07058A, 07057A, 07084A) HANDLE ASSEMBLY (07012A, 07058A, 07057A, 07084A) Parts List 2 1 1 PART NUMBER 170892 NB069300 40540A 1 40517A 1 42183A 1 40543A 1 41948A 5 [6] 7 8 1 1 1 1 47387B 48905A 51523A 71347A 9 10 11 12 1 2.
HANDLE ASSEMBLY HANDLE ASSEMBLY(07060A) (07060A) 22 21 37 28 9 39 41 46 40 38 27 34 13 10 42 29 2 45 42 26 16 24 5 20 48 18 18 43 16 15 12 44 17 11 18 18 30 16 8 33 17 35 25 23 19 32 34 31 47 3 4 14 1 36 7 RF064600 090216 40
HANDLE ASSEMBLY (07060A) HANDLE ASSEMBLY (07060A) Parts List ITEM QTY 1 2 3 4 2 1 1 1 5 [6] 7 8 9 10 11 12 1 1 1 1 1 2.
BASE ASSY 20 2 5 4 16 7 6 1 18 17 19 8 13 12 10 3 1 22 11 23 14 9 2 11 15 21 4 3 42
MOTOR ASSEMBLY MOTOR ASSEMBLY 2 19 6 5 14 4 15 3 21 16 10 11 13 13 12 1 8 20 17 9 7 RF064800 032117 44
MOTOR ASSEMBLY MOTOR ASSEMBLY Parts List ITEM 1 2 3 [ ] [ ] [ ] [ ] [ ] [ ] 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 2 2 2 2 2 1 1" 1 1 PART NUMBER 56380639 AS008400 40542A 41949A 44642A 41306A 41307A 47391A 44648A AS010600 41309A 47392A 77234A 170637 170667 962892 962988 29918A 61089A 61807A 68015A 69031A 70825A 80027A 81208A 81211A 97100A NB072800 71347A MP476500 DESCRIPTION DECAL PROP 65 CORD, MOTOR, EZ-8, AUSTRALIA (07060A) CORD, MOTOR W, L6-15P
DUST CONTROL ASSEMBLY DUST CONTROL ASSEMBLY 18 11 10 19 16 3 12 17 4 5 14 9 4 2 1 6 8 15 13 RF064700 032117 46
DUST CONTROL ASSEMBLY DUST CONTROL ASSEMBLY Parts List ITEM QTY PART NUMBER 1 1 50917A 2 1 167312 3 1 877307 4 2 902567 5 2 915561 6 1 NB003100 7 3 962798 8 4 962826 9 1 22122A 10 1 53741A 11 1 61897A 12 1 65005A 13 1 66159A 14 1 67457A 15 1 67612A 16 1 68285A 17 1 80295A 18 1 30563A 19 1 AS015400 DESCRIPTION BELT FAN EZ-8 RING, RETAINER, INTERNAL RING RETAINING .500 E STYLE BEARING BALL DOUBLE SEALED KEY 1/8 X 1/2 WOODRUFF NUT, HEX, 1/2"-13, JAM SCREW, 10-24 X 1/2 P.H.
SANDING DRUM ASSEMBLY (07012A, 07058A, 07060A, 07084A) 2 13 19 17 25 18 14 23 9 12 24 1 11 5 15 8 16 7 21 10 3 26 27 20 6 Nameplate, Ez-8 48 22 4
SANDING DRUM ASSEMBLY (07057A) SANDING DRUM ASSEMBLY (07057A) 8 2 10 9 14 12 17 15 17 14 16 6 5 11 4 18 13 1 7 3 Parts List ITEM QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 1 1 1 1 1 5 1 2 1 1 1 1 4 1 1 4 1 PART NUMBER 31223A 50916A 66948A 22123A 915082 920365 85517A 962170 51178B 64469A 65310A 66161A 67459A 80027A 80295A AS014600 81211A 13507A DESCRIPTION BUMPER, FRONT BELT, DRUM, EZ-8 RETAINER, BUMPER, PLTD, EZ-8 COVER, FRONT, (EZ-8) KEY, 3/16 SQ.
Wiring Diagram 50
Limited Warranty EZ-8 Sander TO QUALIFY FOR THIS WARRANTY (1) Machine must be registered within 30 days from the time of purchase on a form provided by American Sanders. Your American Sanders Distributor is responsible for the registration of your machine. Please cooperate with your Distributor in supplying necessary information on the card. (2) The machine must have been purchased from American Sanders or an authorized American Sanders Distributor.
American Sanders an AMANO Company 1 Eclipse Rd l PO Box 909 Sparta, North Carolina 28675 l USA www.pioneereclipse.com www.americansanders.