Operation Manual

channels CUE (1) function is selected. To select a channels cue function press the CUE BUTTON

(1) thatisdirectlyassociatedwiththespecificchannelyouwishtomonitor.Youmayusethemixing

functiontoblendboththeCuelevelandtheProgramleveltogether.Youcanvarytheoutputlevelto

eitherhearmoreorlessofeitherofthetwolevels.TurningtheCueMixingknobtotheCUEposition

(left)willallowyou tohearmoreoftheCuelevel.Turningtheknobtothe PGM position(right) will

allowyoutohearmoreoftheProgramlevel(mainoutput).YoumayalsousetheCueMixingControl

toheareithertheCuelevelortheProgramlevelexclusively.IftheknobisinthefullCUEpositionyou

willonlyhearthecuelevel,iftheknobisinthefullPGMpositionyouwillonlyhearthemainoutput.

Thisfunctionisespeciallyusefulwhenmixingwithoutanmonitor.

8. SPLIT CUE - Thisbutton will activate the“Split Cue” function. Whenused with a setofstereo

headphones,theSplitCuefunctionwillassigntheCuesignaltotheleftchanneloftheheadphones

andtheProgram(mainoutput)signaltotherightchanneloftheheadphones.Essentiallysplittingthe

cuesignalinhalf.Thisprocesswillallowforheadphonesmixing.TheCUE MIXING CONTROL (7) will

alsoworkinconjunctionwithfunction.Pleasenotethatthisfunctionwillonlyworkwithasetofstereo

headphones.

9. SHIFT (MIDI) - The button has 2 functions a soft and a hard shift. A soft shift is performed by tog-

gling the shift button, this will be indicated by a blinking shift LED. A hard shift is performed by holding

down the shift button and combining it with another button.

NOTE: When performing a hard shift, it’s recommended you release the secondary button

before releasing the Shift button, this is to prevent MIDI latches unless the MIDI function is a

temporary function.

10. MASTER VOLUME LEVEL INDICATORS - ThedualMASTERLEVELLEDindicatorsareused

todetailthemasterfaderoutputlevel.Themeterswilldetailtheoutputlevelofboththeleftandright

channels.

11. FADER ASSIGN SWITCH -ThisswitchassignsachanneltotheCROSSFADER (13).Whena

channelisassignedtotheleftsideoftheCROSSFADER (13) thatchannelsoutputlevelisroutedto

andcontrolledbytheCROSSFADER (13).SlidingtheCROSSFADER (21)toleftpositionwillsendthe

volumeoutputoftheassignedchannel tothe MASTER VOLUME LEVEL (3),sidingtheCROSSFADER

(13) toright positionwill cutthatchannelsvolumeto MASTER VOLUME LEVEL (3). Thereverseis

truefortherightchannelfaderassignswitch.Whentheassignswitchissettothe“OFF”positionthe

crossfaderwillhavenofunction.

12. HEADPHONE JACK - Thisjackisusedtoconnectyourheadphonestothemixerallowingyouto

monitorthecuesource.Useheadphonesonlyratedat8ohmsto32ohms.MostDJheadphonesare

ratedat16ohm,thesearehighlyrecommended.AlwaysbesuretheCUE LEVEL VOLUME (6) is set to

minimumbeforeyouputtheheadphoneson.

13. FEATHER FADER PLUS CROSSFADER - Thisfaderisusedtoblendtheoutputsignalsofchan-

nelsoneandtwotogether.Whenthefaderisinthefullleftposition(channel1),theoutputsignalof

channelonewillbecontrolledbythemastervolumelevel.Thesamefundamentalswillapplyforchan-

neltwo.Slidingthefaderfromonepositiontoanotherwillvarytheoutputsignalsofchannelsone

andtworespectively.Whenthecrossfaderissetinthecenterposition,theoutputsignalsofboththe

channelsoneandchannelstwowillbeeven.

14. CROSSFADER CURVE ADJUSTMENT - Thisrotaryknobisusedtochangethewaythecross-

faderwilloperate.Thecrossfadercanoperateindifferentmodes,“NORMALCURVE”,“QUICKCURVE”

oranyvariationofthetwo.(QuickCurveisusuallyusedforscratching).

14MXR CONTROLS AND FUNCTIONS cont.