Professional Power Amplifier MONO STEREO BRIDGE LIMITER POWER LIMITER ON ON OVER HEAT ON PROTECT CLIP -5dB -10dB OFF -15dB 0 10 SIGNAL 0 10 PROFESSIONAL POWER AMPLIFIER V4000plus AMERICAN AUDIO ® 4295 Charter Street Los Angeles Ca.
This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of the electrical shock - DO NOT OPEN! CAUTION: To reduce the risk of electrical shock, do not remove cover.
CAUTION Do not open risk of electric shock CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO® DEALER. The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated “dangerous voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.
Important Precautions • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Do not spill water or other liquids into or on to your unit • Do not attempt to operate this unit if the power cord has been frayed or broken • Do not attempt to remove or break off the ground prong from the electrical cord.
Front Panel Control 1 2 3 4 5 6 8 MONO 9 10 11 12 STEREO BRIDGE LIMITER POWER 13 LIMITER ON ON OVER HEAT ON PROTECT CLIP -5dB -10dB OFF -15dB 0 SIGNAL 10 0 10 PROFESSIONAL POWER AMPLIFIER Diagram 1 7 1. Power Switch - This switch is used to control the units main power. 2. Channel 1 Gain Control - This rotary knob is used to control the output signal of channel one. Turning the knob in a clockwise direction will increase signal output. 3.
Rear Panel Control 15 17 20 22 24 26 25 16 18 19 21 23 27 15 Diagram 2 28 29 15. Cooling Fans - Dual high speed cooling fans 16. Channel 2 TRS Input - Channel two 1/4” female jack. Excepts either a balanced or unbalanced plug. See page 7 for more details. 17. Channel 2 XLR Input - Channel two 3-pin XLR balanced input jack. See page 7 for more details. 18. Channel 2 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel two on and off. 19.
Set Up INPUTS - The V4000 V4000plus amplifier allows you to use two types of input connector per a channel, a XLR jack for balanced connections and a 1/4” female jack that will accept balanced and unbalanced connectors. Use these connections to connect the output signal from a mixer, cross-over or EQ to your V4000 V4000plus amplifier. A balanced connection is recommended for cable runs longer that 20ft. When constructing your own XLR cables follow the pin configuration describe below for proper connections.
Bare Wire Connections: Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire insulation 1/2” (13mm). Insert the bare wire into the hole that was reveled by unscrewing the binding post cap. After inserting the wire into the binding post hole, screw the binding post cap down on the wire.
OPERATING MODES: Always configure your amplifier operating mode before beginning operation. If you want to change it during performance. You must decrease the gain controls to their lowest levels to protect the speakers from any popping noise. Stereo Operation - Page 10/Figure 9 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier.
Mono Subwoofer - This operation is similar to the Stereo Subwoofer operation but in mono. When running subwoofers it is usually recommended to run them in mono mode to achieve a cleaner tighter low end. This operation allows you to run several subwoofers down to a minimum of 2 ohms. To avoid amplifier overheating, never run the amplifier below 2 ohms in this mode. Set up this mode as you would a standard stereo set up. Be sure both channels are set to “SUBWOOF” and the mode switch is set to “MONO.
put). Short Circuit Protection can usually be traced back to the signal output line (i.e. speaker line). Check the line from the output terminal of the amplifier to the speaker. If this line good, check the internal speaker connections and components. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. Thermal Protection - Dual variable speed fans on the V4000 V4000plus amplifier provide adequate cooling.
OVERHEAT INDICATOR - Two red LED’s for this function, one for each channel. When the amplifier’s heat sink temperature rises above 91° C., output will be discontinue and the red overheat LED glow continuously. One channel can still operate normally if the other goes into overheat protection mode. SPEAKON ASSEMBLY: You will need a pair of Neutrik Speakon® NL4FC connectors. You will also need high-quality two or four conductor speaker cable, a pair of needle-nosed pliers and a 1.
Bridge Subwoofer Mode Speaker Set-Up Use Ch1 Inputs Do Not Use Ch2 Inputs Set to Bridge Stereo Subwoofer Mode Speaker Set-Up Set to Subwoof Use Ch1 Inputs Use Ch2 Inputs Set to Subwoof Set to Stereo Set to Subwoof Figure 15 Figure 14 Negative (-) Lead Positive (+) Lead Use the two red terminal from the banana jacks to power a subwoofer speaker in mono-bridge mode. Use either the Speakon or the banana jacks ©American Audio® - www.americandj.
TYPICAL STEREO OUTPUT CONNECTIONS Use Speakon or Banana Jacks SPEAKERS 2 OHM MINIMUM SPEAKERS 2 OHM MINIMUM TYPICAL MONO BRIDGE SET-UP Use Channel 1 Inputs Only (XLR or 1/4” Jacks) X Use the two positive binding post termainals (red) for speaker output. SPEAKERS 4 OHM MINIMUM ©American Audio® - www.americandj.
V-SERIES AMPLIFIER SPECIFICATIONS MODEL NO: Output Power: 2 ohms, 1 khz 1% THD 4 ohms, 1khz, 1%THD 8 ohms, 1khz 1% THD (Bridge Mode, mono) 4 ohms, 1khz, 1% THD 8 ohms, 1khz, 1% THD Total Harmonic Distortion: 20Hz-20kHz, @ rated output power, 8 ohms Input Sensitivity and Impedance: @ rated output power, 8 ohms Dimensions & Weight: Weight: Height Width Depth W Weight Frequency Response: +/- 1db, 1w RMS. 8 ohms +/- 0.2 db, @ rated output, 8 ohms V-1000 PLUS V-1500 315w RMS Per Ch. N/A 245w RMS Per Ch.
©American Audio® American Audio® is part of the American DJ® Group of Companies American DJ® World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-2650 / Fax: 323-582-2610 web: www.americandj.com / e-mail: info@americandj.