Owner's manual

ManualsBrandsAmerican Bicycle Security Company ManualsFor bicyclesBike Haven

The Bike Haven bridges the

gap between short and long

term bike parking. Starting

with a simple canopy

design, the design team

worked to provide a solid,

secure structure with full

coverage. Optional

polycarbonate side and

back panels are available

for additional protection.

The Bike Haven is

available with or without

racks to accommodate

existing bike parking. And

as demand grows, the Bike

Haven’s modular design

makes it easy to add more

sections.

American Bicycle Security Company

P.O. Box 7359

Ventura, CA 93006

Ph: (800) 245-3723 or (805) 933-3688

Fax: (805) 933-1865

www.ameribike.com

Email: turtle@ameribike.com

Bike Haven

Summary of content (6 pages)

PAGE 1
Bike Haven The Bike Haven bridges the gap between short and long term bike parking. Starting with a simple canopy design, the design team worked to provide a solid, secure structure with full coverage. Optional polycarbonate side and back panels are available for additional protection. The Bike Haven is available with or without racks to accommodate existing bike parking. And as demand grows, the Bike Haven’s modular design makes it easy to add more sections. American Bicycle Security Company P.O.
PAGE 2
Bike Haven Product Bike Haven Capacity See diagrams below and to left Materials Uprights: 4” x 3/16” square tube. Feet: 3/8” plate Roof Member: 4” x 3/16” square tube Roof Member Long: 2” x 4” x 1/8” tube Roof Panels: Type S deck 26g galvanized steel Panels: ¼” clear polycarbonate with 1.77” square aluminum framing Finishes An after fabrication hot dipped galvanized finish is our standard option.
PAGE 3
Bike Haven Parts List Tools needed for Installation: Tape Measure Marker or pencil Level Hammer Rubber Mallet Drill (Hammer Drill Recommended) 5/16” Socket with drill attachment ½” Masonry Bit ¾” Wrench/Socket 9/16” Wrench/Socket Philips Head Screwdriver Heavy Lifting Equipment ¼” Masonry Drill Bit (for panels) ½” Drill Bit (for panels) American Bicycle Security Company P.O. Box 7359 Ventura, CA 93006 Ph: (800) 245-3723 or (805) 933-3688 Fax: (805) 933-1865 www.ameribike.com Email: turtle@ameribike.
PAGE 4
Bike Haven 1. Installation Instructions – Starter Section Customer is responsible for preparing the slab with minimum strength of 2500psi as shown HSS 4” X 4” X 3/16” Typical Column in Weldment Sidewalk Footing = Minimum 5’ X 5’ X 5” concrete surround at base connection Field Footing = Minimum 42” X 42” X 12” concrete surround at base connection 90.00 2. 140.00 Lay an UPRIGHT SHORT and UPRIGHT TALL on the ground parallel to each other and about 86” apart.
PAGE 5
Bike Haven 4. 6. Installation Instructions – Starter Section Place the initial ROOF PANEL at one end of the assembly. The panel should cover both openings at the top of the uprights. With a self-drilling screw, drill through the ROOF PANEL and ROOF MEMBER LONG in noted points. You may want to clamp a wood 2x4 to both UPRIGHT SHORTS at the level of the ROOF panel, so that all the ROOF PANELS stay aligned with each other. Place the next ROOF PANEL in place, drill where noted.
PAGE 6
Bike Haven 8. Installation Instructions Drill a ¼” hole in the ground at the slotted hole in the REAR PANNEL foot and secure with a ¼” wedge anchor. 9. Place the SIDE PANEL in place and clamp it to the UPRIGHTS. Using the four ½” holes in the SIDE PANEL as a guide, drill through both walls of the UPRIGHTS with a 3/8” drill bit. Bolt the SIDE PANEL to the UPRIGHTS with the aluminum spacers in between the SIDE PANEL and UPRIGHTS. Repeat for the other SIDE PANEL.