User Manual

ManualsBrandsAmerican DJ ManualsLightsInno Pocket Z4 - 10W RGBW LED MOVING HEAD

User Instructions

7/15

INNO POCKET Z4

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Inno Pocket Z4 Specifications

Model: Inno Pocket Z4

Voltage: 100 - 240V, 50/60Hz

LED: 4 x 10W 4-in-1 RGBW LEDs

Power Consumption: 67W

Dimensions: 5.5”(L) x 6.75”(W) x 9.75”(H)

141 x 174 x 247mm

Weight: 7 Lbs. / 3.2 kgs.

Beam Angle: 10 - 60 Degrees

Fuse: 3.15 Amp

Duty Cycle: None

DMX: 3 DMX Channel Modes: 16/19/22

Colors: RGBW Color Mixing

Sound Active: Yes

Working Position: Any Safe, Secure Position

Warranty:

2 Year (730 days) US+Canada only

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged

into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: info@americandj.com

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

service@adjgroup.eu / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Summary of content (16 pages)

PAGE 1
Inno Pocket Z4 Specifications Sound Active: 5.5”(L) x 6.75”(W) x 9.75”(H) 141 x 174 x 247mm 7 Lbs. / 3.2 kgs. 10 - 60 Degrees 3.15 Amp None 3 DMX Channel Modes: 16/19/22 RGBW Color Mixing INNO POCKET Z4 2 Year (730 days) US+Canada only Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
PAGE 2
©2015 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
PAGE 3
Inno Pocket Z4 Fuse Replacement Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.
PAGE 4
Inno Pocket Z4 General Instructions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
PAGE 5
Inno Pocket Z4 Channel 18 19 20 21 22 Value 132 - 139 140 - 181 182 - 189 190 - 231 232 - 239 240 - 247 248 - 255 0 - 255 0 - 255 0 - 69 70 - 79 80 - 89 90 - 199 200 - 209 210 - 255 0 - 20 21 - 40 41 - 60 61 - 80 81 - 100 101 - 255 22 Channel Mode Function SHUTTER/STROBE OPEN FAST CLOSE - SLOW OPEN OPEN SLOW CLOSE - FAST OPEN OPEN RANDOM STROBING OPEN MASTER DIMMER 0% - 100% PAN/TILT MOVEMENT SPEED FAST - SLOW SPECIAL FUNCTIONS NO FUNCTION BLACKOUT W/ PAN/TILT MOVEMENT DISABLE BLACKOUT WITH PAN/T
PAGE 6
Inno Pocket Z4 Mounting When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
PAGE 7
Inno Pocket Z4 Channel Value 1 2 3 4 5 6 7 8 9 10 11 12 13 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0-7 8 - 11 12 - 15 16 - 19 20 - 22 23 - 26 27 - 30 31 - 34 35 - 37 38 - 41 42 - 45 46 - 48 49 - 52 53 - 56 57 - 60 61 - 63 64 - 67 68 - 71 72 - 75 76 - 79 80 - 82 83 - 85 86 - 89 22 Channel Mode Function PAN MOVEMENT 0°-540° PAN FINE TILT MOVEMENT 0°-180° TILT FINE RED 1 0% - 100% GREEN 1 0% - 100% BLUE 1 0% - 100% WHITE 1 0% - 100% RED 2 0% -
PAGE 8
Inno Pocket Z4 DMX Set Up Power Supply: The ADJ Inno Pocket Z4 contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers.
PAGE 9
REMOTE CONTROL INPUT SOUND Inno Pocket Z4 Channel 13 14 15 16 17 18 19 Channel Mode Value 90 - 93 94 - 97 98 - 101 102 - 104 105 - 108 109 - 112 113 - 115 116 - 119 120 - 123 124 - 127 128 - 191 192 - 255 0 - 255 0 - 255 0-7 8 - 15 16 - 131 132 - 139 140 - 181 182 - 189 190 - 231 232 - 239 240 - 247 248 - 255 0 - 255 0 - 69 70 - 79 80 - 89 90 - 199 200 - 209 210 - 255 SOUND REMOTE CONTROL INPUT INPUT OUTPUT 2 3 ADJ Products, LLC - www.adj.
PAGE 10
Inno Pocket Z4 DMX Set Up Inno Pocket Z4 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- Channel Value 3-Pin XLR to 5-Pin XLR Conversion 1 2 3 4 5 6 7 8 9 10 11 12 13 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line.
PAGE 11
Inno Pocket Z4 16 Channel Mode Channel Value Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 PAN MOVEMENT 0°-540° PAN FINE TILT MOVEMENT 0°-180° TILT FINE RED 1 0% - 100% GREEN 1 0% - 100% BLUE 1 0% - 100% WHITE 1 0% - 100% RED 2 0% - 100% GREEN 2 0% - 100% BLUE 2 0% - 100% WHITE 2 0% - 100% ZOOM 10°- 60° SHUTTER/STROBE CLOSED OPEN STROBING SLOW - FAST OPEN FAST CLOSE - SLOW OPEN OPEN SLOW CLOSE - F
PAGE 12
Inno Pocket Z4 System Menu System Menu: When making adjustments press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds. To exit without making any adjustments press the MENU button. The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock. ADDR - DMX Address Setting. 1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER. 2. The current address will now be displayed and flashing.
PAGE 13
Inno Pocket Z4 Master-Slave Set Up Master-Slave Operation This function will allow you to link up to 16 units together and operate without a controller. The units will be sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave. 1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the units.
PAGE 14
Inno Pocket Z4 System Menu DNST - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted, or power is lost, the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied. 1. Press the MENU button until “DNST” is displayed, and either “MASL”, “BLND”, or “LAST” will be displayed beneath. 2.
PAGE 15
Inno Pocket Z4 Home Adjustment Menu Inno Pocket Z4 PINT - Pan Inversion System Menu 1. Press the MENU button until “PINT” is displayed, press ENTER. Either “Yes” or “No” will be displayed. To enter the home position adjustment menu, press the ENTER button for at least 5 seconds. In this submenu you are able to adjust the original position of the pan position and tilt position. PAN - Adjustment of the pan position. 1.
PAGE 16
Inno Pocket Z4 System Menu again. Press ENTER when you have made your desired setup. TEST - This function will run a self test program. 1. Press the MENU button until “TEST” is displayed, press ENTER. Inno Pocket Z4 System Menu 2. The running time of the fixture will now be displayed. Press MENU to exit. VER - Use this function to display the Software version of the unit. 2. The fixture will now run a self test. 1. Press the either the MENU button until “VER” is displayed, press ENTER.