User Manual

ADJ Products, LLC - www.adj.com - Inno Pocket Z4 Instruction Manual Page 8
lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.
Inno Pocket Z4 DMX Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground
1 Ground
XLR Male Socket
XLR Pin Conguration
3 Hot
2 Cold
2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 4
ADJ Products, LLC - www.adj.com - Inno Pocket Z4 Instruction Manual Page 23
Inno Pocket Z4 19 Channel Mode
Channel Value Function
13 COLOR MACROS
90 - 93 COLOR MACRO 23
94 - 97 COLOR MACRO 24
98 - 101 COLOR MACRO 25
102 - 104 COLOR MACRO 26
105 - 108 COLOR MACRO 27
109 - 112 COLOR MACRO 28
113 - 115 COLOR MACRO 29
116 - 119 COLOR MACRO 30
120 - 123 COLOR MACRO 31
124 - 127 COLOR MACRO 32
128 - 191 COLOR CHANGING
192 - 255 COLOR FADING
14 COLOR CHANGE/FADE SPEED
0 - 255 SLOW - FAST
15 0 - 255 ZOOM 10°- 60°
16 SHUTTER/STROBE
0 - 7 CLOSED
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 FAST CLOSE - SLOW OPEN
182 - 189 OPEN
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 OPEN
240 - 247 RANDOM STROBING
248 - 255 OPEN
17 0 - 255 MASTER DIMMER 0% - 100%
18 SPECIAL FUNCTIONS
0 - 69 NO FUNCTION
70 - 79 BLACKOUT W/ PAN/TILT MOVEMENT
80 - 89 DISABLE BLACKOUT WITH PAN/TILT
MOVEMENT
90 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 255 NO FUNCTION