Specifications

ManualsBrandsAmerican DJ ManualsCD PlayerDCD-PRO300

194

XLS SERIES

Specifications

The following applies to units in Stereo mode with 8-ohm

oads and rated input sensitivity unless otherwise specified.

erformance

Sensitivity (volts RMS) for full rated power at:

4 ohms: 0.725

(XLS 202)

ohms: 1.025

(

XLS 402)

4 ohms: 1.26 (XLS 602)

Frequency Response (at 1 watt) 20 Hz to 20 kHz: ±0.75 dB.

Phase Response (degrees at 1 watt)

at 10 Hz: –10.

at 20 kHz: +19.

Signal-to-Noise Ratio (20 Hz to 20 kHz)

A-weighted, below rated power: > 100 dB.

No weighting, below rated power: > 97 dB.

Total Harmonic Distortion (THD) at full bandwidth power,

from 20 Hz to 1 kHz: < 0.15%.

Intermodulation Distortion (IMD) (60 Hz and 7 kHz at 4:1)

from full rated output to –40 dB: < 0.3%.

Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.

Crosstalk (below rated power)

at 1 kHz: –82 dB.

at 20 kHz: –58 dB.

Voltage Gain (at maximum output): 31 dB.

Power

Load Impedance: Safe with all types of loads. Rated for 2 to

8 ohms in Stereo, 8 ohms in Bridge-Mono.

AC Line Voltages Available (±10%): 120 and 230 VAC.

Line Frequency: 50/60 Hz.

Controls

Level: Two front-panel, black rotary level controls, one for

each channel.

Power: Front-panel switch; on when in the UP position.

Filter Switches: One per channel; three-position back-panel

switches set the frequency for internal high-pass filters.

requency setting is 30 Hz when switch is in left position; 15

Hz when switch is centered; and bypassed when switch is in

right position.

Limiter Switch: Back-panel switch offers loud-speaker

protection against moderate amplifier clip when set to the “IN”

position.

Fuse: Provides overload protection.

Indicators

Clip: Two front-panel red LEDs, one for each channel,

illuminate when the channel’s output signal is being

overdriven.

Power: Green front-panel LED indicates amplifier has been

turned on and AC power is available.

Fault: Yellow front-panel LED illuminates when amplifi er is in

protect mode. Also illuminates briefly during normal power-up

when amplifier is first switched on.

The XLS Series of power amplifiers from Crown represents a new era in affordable, quality

power amplification. The line consists of three models in a uniform, rugged chassis, incorpo-

ating the best of tried-and-true design principles and innovative features. XLS Series

amplifiers are professional stereo power amplifiers engineered to meet demanding audio

requirements—reliably and within budget. Plus, every XLS Series amplifier is backed by

Crown’s unequaled Three-Year, No-Fault, Fully-Transferrable Warranty that covers everything.

XLS 402

Output Power:

2-ohms Stereo (per channel)

570W

4-ohms Stereo (per channel)

400W

8-ohms Stereo (per channel)

260W

XLS402

LIST......$519.00

XLS 602

Output Power:

2-ohms Stereo (per channel)

840W

4-ohms Stereo (per channel)

600W

8-ohms Stereo (per channel)

370W

XLS602

LIST......

$692.00

XLS 202

Output Power:

2-ohms Stereo (per channel)

250W

4-ohms Stereo (per channel)

200W

8-ohms Stereo (per channel)

145W

XLS202

LIST ......$429.00

CE1000A3 LIST...........$740.00

CE2000A3 LIST........$1,056.00

CE4000CE4D LIST... $2,079.00

Once again, LPD leads the way! Introducing

the NEW Crown XLS Series amplifiers.

INPUT/OUTPUT

Input Connectors: 3 balanced

inputs per channel - Neutr

Combo (1/4” TRS/XLR) and

barrier block.

Output Connectors:Neutrik

NL4 Speakon (1 per channel)

plus 5-w

y binding post.

CE1000

DUAL 560W 2 ohms

450W 4 ohms

275W 8 ohms

BRIDGED 1100W 4 ohms

900W 8 ohms

CE2000

DUAL 975W 2 ohms

660W 4 ohms

400W 8 ohms

BRIDGED

1950W 4 ohms

1320W

8 ohms

CE4000

1,800W*

2 ohms

1,200W 4 ohms

600W 8 ohms

BRIDGED 3,600W* 4 ohms

(*at g

reater than or equal to 200

C line voltage)

The CE Ser

ies - pro

vides an accur

ate

, uncolored, sound with v

ery low

distortion, for the best in music and voice reproduction. A Bridge-

Mono/Stereo mode switch allows you to set up your amp/speaker in the

configuration that best suits your needs. An advanced protection circuitry

guards against shor

ted outputs

, open circuitry, DC, mismatched loads,

general overheating, high-frequency overloads and internal faults. System

Solution Topologies (SST) input modules customize your CE amplifier to

better ser

e y

our needs. All CE amplifiers are ETL

appro

ed.

CE SERIES

CE4000CE4D Features: BCA circuitr

y; signal, fault, clip indicators; stereo & bridge-mono modes; choice of input and output connectors;

selectable filters, aux fault jack; front panel level controls; 3 position input sensitivity switch. 3-speed fan on demand.