User manual
ADJ Products, LLC - www.adj.com - MEGA GO PAR64 RGBA User Manual Page 13 ADJ Products, LLC - www.adj.com - MEGA GO PAR64 RGBA User Manual Page 14
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the “Slave” unit to DMX adressing and then connect the
“Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation. The
“Slave” unit will now follow the “Master”.
MEGA GO PAR64 RGBA Master-Slave Configuration
Battery Life:
This menu is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until “bXXX” is dis-
played. “XXX” represents a number between 0-100. The number
that is displayed is the remaining battery life. If “b---” is displayed,
it means either the battery is dead or your running the unit on AC
power.
MEGA GO PAR64 RGBA Operating Instructions MEGA GO PAR64 RGBA Operating Instructions
is displayed. This is the 1 Channel DMX Mode.
To run the 2 Channel Mode, press the MODE button until “Ch02”
is displayed. This is the 2 Channel DMX Mode.
To run the 4 Channel Mode, press the MODE button until “Ch04”
is displayed. This is the 4 Channel DMX Mode.
To run the 5 Channel Mode, press the MODE button until “Ch05”
is displayed. This is the 5 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until “Ch06”
is displayed. This is the 6 Channel DMX Mode.
To run the 7 Channel Mode, press the MODE button until “Ch07”
is displayed. This is the 7 Channel DMX Mode.
To run the 8 Channel Mode, press the MODE button until “Ch08”
is displayed. This is the 8 Channel DMX Mode.
4. Please see pages 16-19 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
ADJ RFC (Remote Control) On/Off:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see page 15 for the controls and func-
tions.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “rFXX” is displayed. “XX” repre-
sents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the
MODE button to exit.
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 30 xtures maximum. After 30 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
NOTE: Fixtures cannot be power cord daisy chained and run by
battery power.
MEGA GO PAR64 RGBA Power Cord Daisy Chain