Operating instructions

Programming a System Tour
To select a tour for programming:
1. Move the cursor to TOUR entry in the title line of the SET
SYSTEM TOURS menu (page 4-5).
2. Enter the desired tour number (1 - 24) on the keypad.
3. Press the ACK button.
Eight tour entries are displayed per page for programming.
See page 4-3 for menu paging instructions.
CAM (Camera)
To add or change a camera in the tour:
1. Move the cursor to the CAM column of the desired entry.
2. Enter a camera number (1 to 32) on the keypad.
3. Press the ACK button. The camera number appears in the
CAM column menu entry.
DWL (Dwell Time)
To set or change a dwell time for a camera:
1. Move the cursor to the DWL column for the desired entry.
2. Enter the desired dwell time (1 to 60 seconds in one second
increments). If 61 is entered, the dwell time is set to a hold
condition for the selected camera.
3. Press the ACK button. The dwell time appears in the DWL
column.
PRE (Preset)
To select a preset scene (which has already been defined):
1. Position the cursor to the PRE column of the desired entry.
2. Enter the preset number (1 to 72). Zero represents no
preset call for this entry.
3. Press the ACK key. The preset number appears under the
PRE heading.
AUX (Auxiliary)
If an auxiliary action is desired for this entry:
1. Move the cursor to the AUX column for the desired entry.
2. Enter one of the following auxiliary numbers and press the
ACK button. The selection is displayed under the AUX
column.
1 = aux 1 ON 5 = aux 1 OFF
2 = aux 2 ON 6 = aux 2 OFF
3 = aux 3 ON 7 = aux 3 OFF
4 = aux 4 ON 8 = no aux call
or
Press the ACK button to cycle through the auxiliary
actions. Press the NEXT button to save the displayed
entry.
CN (Connect Next)
If a salvo switching is desired at a tour entry:
1. Position the cursor to the CN entry to be changed.
2. Enter the one of the following numbers and press the ACK
button. The selection is displayed in the CN column entry.
1 = N, no connect next
2 = Y, connect to next tour entry
3 = S, call a System Salvo
or
Press the ACK button to cycle through the CN values. The
entry displays “N”, “Y”, or “S” each time ACK is pressed.
Press the NEXT button to save the displayed entry.
If a System Salvo (S) is selected, the CAM number for this
entry must be set to the desired Salvo number.
If Connect Next (Y) is selected, the dwell times for each salvo
group is controlled by the first entry of the group. The dwell
time for all but the first entry in the salvo group may be left
blank. All entries in a connect next sequence should have the
CN entry set to Y except the last entry, which is set to N.
Example:
The following menu shows sample entries made to System
Tour 11. These associate Camera 17 with tour entry 06, set a
dwell time of 30 seconds for this camera, with a preset of 25,
AUX 1 ON, and salvo connect to the next entry (07).
SET SYSTEM TOURS
TOUR - 01
ENT CAM DWL PRE AUX CN
01 01 02 00 0- N
02 02 02 00 0- N
03 03 02 00 0- N
04 04 02 00 0- N
05 05 02 00 0- N
06 17 30 25 1-ON Y
07 07 00 07 0- N
08 08 02 00 0- N
PREVIOUS MENU
Note that the Dwell Time for tour entry 07 is set to zero since
its dwell time is controlled by the first entry of the salvo group,
entry 06.
4-6
MENU PROGRAMMING - SYSTEM MENU