COLOR VIDEO CAMERA ADC770 INSTRUCTIONS ∞ BF LO OK L DIGITA For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. ADC770 Serial No. LWT0188-001A-H E-1 e01_adc770(01_05)e.
These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. 2. 3. 4. Read all of these instructions. Save these instructions for later use. All warnings on the product and in the operating instructions should be adhered to. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5.
13. Follow all warnings and instructions marked on the appliance. 14. Do not overload wall outlets and extension cords as this can result in fire or electric shock. 15. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. 16.
Safety Precautions FOR USA AND CANADA Due to design modifications, data given in this instruction book are subject to possible change without prior notice. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Thank you for purchasing this product. (These instrustions are for ADC770) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. CONTENTS INTRODUCTION Features ............................................................................................................................... 6 Operating Precautions ...................................................................................................
INTRODUCTION Features A new DSP (Digital Signal Processor) features a Extended Dynamic Range (ExDR) and enables to shoot both bright and dark locations. The use of a new CCD with a SENSE UP (X32) function realized the minimum luminous flux density for subject of 0.8 lx (F1.2, 50%, AGC 20dB) and 0.025 lx (at slow shutter). A motion detector function detects the motion inside an image and emits alarm signals.
Operating Precautions ● To save energy, when it is not being used turn the system’s power off. ● This camera has been designed for indoor use. When you use it outdoor, be sure to use a housing and the like. ● Do not install or use the camera in the following places. • In a place exposed to rain or moisture. • In a place with vapor or oil soot, for example in a kitchen. • When the ambient temperature rises above or falls below the acceptable range (from –10°C to 50°C).
INTRODUCTION Controls, Connectors and Indicators 2 1 3 4 5 7 1 Lens mount 6 4 Camera-mounting bracket This means to attach the lens. This is applicable to both the C-mount lenses and CS-mount lenses. 2 Backfocus adjustment ring Adjusting the back focus during lens installation. When readjustment is required, loosen the locking screw 3 by turning it counterclockwise and turn the back focus adjustment ring 2 . After the adjustment, tighten the locking screw 3 again.
! @# $ SET AWC MENU CAMERA SETUP EXT TERM-OFF INT/GL ON LL NOT USED VIDEO % ^ IRIS DC 8 8 Cover 90 12 [SET/AWC] Set. Auto White Control The cover opens if it is pulled to the left while being pushed. 9 [VIDEO/DC] Iris Selector Switch This is set according to the type of lens when an automatic iris control lens is used. VIDEO: In case of lens with EE amp builtin. DC: In case of lens without EE amp built-in.
INTRODUCTION Controls, Connectors and Indicators (Continued) 13 [ , , , ] Up-and-down, left-andright Button These buttons select items on the menu screen and change a set value. ( Page 23) 14 [EXT.TERM-ON/OFF] Terminal On/Off Switch of External Synchronization Signal This is a terminating ON/OFF switch for the external synchronization input signal. When this is switched ON, termination is executed via a 75 Ω resistor. ON: terminates at 75Ω. OFF: does not terminate at 75Ω.
* + - 1 2 REMOTE CLASS 2 ONLY(U TYPE) ISOLATED POWER ONLY (E TYPE) AC24V DC12V & AUX GND ¤ Y/C OUT SYNC IN ⁄ ( VIDEO OUT POWER SEE INSTRUCTION MANUAL ) 17 [DC 12V, AC 24V] Power input terminals To input DC 12V or AC 24V power. 18 [AUX, GND] Auxiliary Output Terminals If any change occurs in the area that was set on the MOTION DETECT screen, these terminals output signals. ( Page 31) [Open-collector Low signal. Maximum voltage 30V, Current 30mA.
CONNECTION/INSTALLATION Procedures Execute connection/installation according to the procedures described below. Turn OFF the power supply to all equipment to be used before making carefully. 4.Setting the switches 6.Back focus adjustment (墌 Page 17) (墌 Page 21) SET CAMERA SETUP EXT TERM-OFF INT/GL ON LL VIDEO H ALC LEVEL NOT USED Av Pk L AWC MENU IRIS DC 5.Lens adjustment 7.Auto white balance control adjustment (墌 Page 22) (墌 Page 20) 3.Mounting the camera 1.
DC 12V/AC 24V power supply 2.Connections To alarm terminals such as switches ( Page 15) AC24V DC12V 1 REMOTE 2 CLASS 2 ONLY(U TYPE) ISOLATED POWER ONLY (E TYPE) AUX GND Genlock sync signal generator Y/C OUT SYNC IN POWER VIDEO OUT SEE INSTRUCTION MANUAL Monitor E-13 e02_adc770(06_22)e.
CONNECTION/INSTALLATION Mounting the lens Mount the lens according to the procedures described below. 1. CK LO BF (b) F (c) 3. Before mounting a lens, check whether it is a C-mount or CS-mount lens. To change the mounting method, loosen the back-focus locking screw (M 2.6) using a Phillips head screwdriver, turn the back-focus adjusting ring with your fingers or the screwdriver and change the mounting method. Dimension (b) of the lens shown in the illustration must be as shown in the table below.
Connections on the back Power supply AC24V DC12V 1 Connect the DC 12 V or the AC 24 V power supply to the DC 12V/AC 24V terminals. To prevent connection errors or a cable disconnection, we recommend the use of lug plates for the connections. The following table shows the connection distances and connection cables provided that 2-conductor VVF cables (vinyl-insulated vinyl sheath cables) are used.
CONNECTION/INSTALLATION Connections on the back (Continued) Genlock connection With some systems, when the external sync signal is a composite video or black burst signal genlocking by applying an external sync input requires the horizontal phase (H PHASE) and colour phase (SC COARSE) to be adjusted. MEMO • Genlocking is not possible with a signal containing too much jitter, such as a VCR or videodisc playback signal. Setting the swaitches E-16 e02_adc770(06_22)e.
Setting the switches EXT TERM-OFF INT/GL SET AWC MENU CAMERA SETUP EXT TERM-OFF INT/GL ON LL ON LL NOT USED NOT USED VIDEO IRIS DC Select the synchronization method of the camera image. Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE. (墌 Page 26.) E-17 e02_adc770(06_22)e.
CONNECTION/INSTALLATION Mounting the camera Camera mounting screw When mounting the camera on a fixer, pan/ tilt, etc., use the camera mounting screw hole located on the camera-mounting bracket. Camera-mounting bracket CAUTION: Use the screw with a length shorter than 7mm from a camera-mounting face. MAX. 7mm Furthermore, make use of the rotation prevention hole to prevent the camera from falling and securely mount the camera.
q IRIS VIDEO DC w Installation of camera • Mounting from the bottom This camera is originally designed to be mounted from the bottom, as shown q. The hole is standard photographic panhead screw size (1/4-20 UNC). Example the Fixing unit or Pan/Tilt unit. • Mounting from the top Remove the CAMERA MOUNTING BRACKET from the bottom of the camera by removing two fixing screws as shown w. Attach the CAMERA MOUNTING BRACKET to the top, then mount the camera on the Fixing Unit as shown e.
CONNECTION/INSTALLATION Lens adjustment Connect the camera according to the connection method, turn it on, display an image on the monitor, and check the image. The camera has been factory-adjusted to the best position, but it may need to be adjusted according to the object conditions or combination of lenses. If the image is unnatural, adjust it as follows: (Also read the instruction manual of the lens.
Back focus adjustment Back focus adjustment Be sure to make back-focus adjustments when changing the lens mounting method or using a different lens. If required, adjust it as follows: • With a fixed-focus lens If the focus can not be adjusted correctly by rotating the lens focus ring, adjust the back focus as follows. Back focus adjusting ring Tighten Loosen CK LO BF Back focus fixing screw (M2.6) 1. Loosen the back focus locking screw by turning it counterclocckwise ( ) with a screwdriver. 2. 3.
CONNECTION/INSTALLATION Auto white balance control adjustment Each light source has its own colour temperature. Therefore, when the main light source lighting an object is changed, the white balance should be adjusted again by pressing the AWC button. AWC button SET AWC MENU CAMERA SETUP EXT TERM-OFF INT/GL ON LL 1. Place a white object under the same lighting condition as the object to be shot and zoom in to fill the screen with white. 2. When the AWC button is pressed for approx. one sec.
MENU SETTING Setting the menu 4. MENU button Use the , button to set the cursor (>) to a desired item. A L C SE T T I NGS SET SET button CAMERA SETUP AWC MENU I R I S L E VE L A V E RA GE : P EAK S H UT T ER ( E x DR ) A G C MODE L O L U X MODE S E NS E U P P R I OR I T Y B LC 5. SET AWC MENU CAMERA SETUP EXT TERM-OFF INT/GL ON LL Change the set value using the , button. Change of the set value displays a change mark (∗). NOT USED IRIS VIDEO A L C SE T T I NGS DC ∗I R I S 1.
MENU SETTING The flow of menu screen Page 26 MENU SYNC A D J US T V PHASE H PHASE S C COARS E S C F I NE S YNC A DJ UST . . A L C S E T T I NGS . . V I DEO A DJ UST . . MODE S E L ECT . . MOT I ON D E T E CT . . F A C TORY SET T I NGS . . 0 0 0 1 28 Page 30 Page 35 V I DE O ADJ U ST WH I T E BAL A NCE COL OR L EVEL E N HANCE L E V E L P E DE ST AL LE V E L AU T O BL AC K C T L IR AV SH AG LO SE PR B WH I T E BALANC E CONT RO L ATW NORMAL NORMAL NORMAL OF F AWC SE T . .
SHUT TE R ( E x DR ) S HUT T ER SPEED F AST L I M I T E x D R L EV E L M . E x D R SPEED 1 / 120 – –– – –– – –– Page 26 A L C SE T T I NGS I R I S L E VE L A V E RA GE : P EAK S H UT T ER ( E x DR ) A G C MODE L O L U X MODE S E NS E U P P R I OR I T Y B LC OL : : NORMAL 8:2 N O RMAL 2 0 dB OF F OF F ––– OF F Page 34 B G Page 31 MODE S EL E C T CAMERA T I T L E ED I T . . RE V ERS E MODE OF F AL M .
MENU SETTING SYNC ADJUST Screen This executes the setting regarding synchronization. Item Functions and set values Initial value V PHASE This adjusts the vertical synchronization to those of other cameras when a selector switch for the synchronizing system on the side is at LL. (60Hz power region only.) When it is not set to LL, “---” will appear, disabling change the set value.
Item Functions and set values Initial value SHUTTER (ExDR) This sets the electronic shutter as well as the ExDR (Extended Dynamic Range). The use of an electronic shutter function enables shooting with proper brightness, as more brightness results in higher shutter speed. The ExDR function allows even the shooting of a subject having different luminous flux density by composing a picture shot at 1/120 sec. shutter speed with a picture shot by a high-speed shutter.
MENU SETTING ALC SETTINGS Screen (Continued) Item Functions and set values Initial value FAST LIMIT This sets the fastest value of a shutter speed when AUTO is set. The MANUAL, M. ExDR, A. ExDR set value is displayed as “- - -” and cannot be changed. The higher the shutter speed becomes, the more smear phenomenon is emphasized, which is peculiar to the CCD.
Item Functions and set values Initial value PRIORITY This item sets the order in which the AGC and slow shutter speed decrease function when the object brightness becomes low. When the item AGC MODE or the item SENSE UP is set to OFF, “- - -” will appear, disabling any setting. MOTION: Priority is given to motion. This is suitable to a subject with quick motion, since the AGC (automatic gain control) functions with priority when the subject becomes dark. PICTURE: Priority is given to image.
MENU SETTING VIDEO ADJUST Screen Adjustments are made on video signals. Item Functions and set values Initial value ATW WHITE BALANCE Selects the white balance adjustment function. The white balance can be adjusted manually or automatically for light within the colour temperature range of 2500K to 8000K. • ATW: Auto-Tracking White Balance mode. This automatically adjusts the white balance. • AWC: Auto White Balance Controll mode. When the SET button is pressed, the adjustment screen appears.
MODE SELECT Screen Titles, image reversion, etc., are set. Item Functions and set values Initial value CAMERA TITLE EDIT Bring up the CAMERA TITLE, EDIT screen. ( Page 36) REVERSE MODE Settings are executed for image reversion. OFF: Image does not reverse. R-L: Left and right of the image are reversed. U-D: Up and down of the image are reversed. ALL: Up and down and left and right of the image are reversed. OFF ALM.TITLE SIZE Set the size of the characters displayed in the case of alarms.
MENU SETTING MOTION DETECT Screen (Continued) Item Functions and set values Initial value LEVEL This sets the level that detects motion. If the item MODE is set to OFF, “- - -” will appear, and settings cannot be changed. To function with large signal level change…decrease the value To function with small signal level change…increase the value [Set values: –5 to NORMAL to 5] NORMAL AREA EDIT This sets the range in which the motion detecting function works.
FACTORY SETTINGS Screen Set values are returned to initial values. Item FACTORY SETTINGS Functions and set values Initial value The values set on the menu are returned to initial values. CANCEL : No return to the initial value. CLEAR : Returns set values except titles to the (WITHOUT TITLE) initial value. CLEAR (ALL) : Returns all set values including titles to the initial value. Select respective set value and press the SET button. Then, “DATA CLEARED” will appear for about 3 seconds.
MENU SETTING BLC EDITTING Screen It is possible to set freely the light metering area for backlight compensation. The 2 screens of EDIT1 and EDIT2 can be set. MENU button SET button A L C SE T T I NGS I R I S L E VE L A V E RAGE : P EAK S H UT T ER ( E x DR ) A G C MODE L O L U X MODE S E NS E U P P R I OR I T Y B LC NORMAL 8:2 N O RMAL 2 0 dB OF F OF F MOT I ON EDIT 1 SET AWC MENU CAMERA SETUP EDIT 1 screen Light metering area 1. Set the item BLC on the ALC SETTING screen to EDT1. 2.
Manual Adjustment of White Balance When automatic adjustment of the white balance results in a “reddish screen”, etc., adjust the white balance manually. MENU button SET button 1. Set the WHITE BALANCE item on the VIDEO ADJUST screen to AWC and press the SET button. * The WHITE BALANCE adjustment screen appears on the monitor. 2. Select the hue to be adjusted. (R/B or Mg/G) Press the or button. 3. Adjust the hue. Press the or button. * The “ ı ” indicator moves in accordance with the setting.
MENU SETTING CAMERA TITLE Setting Up to 24 characters can be selected as camera text for each camera. The set characters are displayed at the bottom of the screen. MENU button SET button 1. Then, the CAMERA TITLE screen is brought up. SET CAMERA SETUP AWC MENU Select the item CAMERA TITLE on the MODE SELECT screen, and push the SET button. 2. Select the first character from the character area using buttons. The selected character is displayed flashing on and off. 3.
Setting the MOTION DETECT Function It is possible to set freely the area where MOTION DETECTING functions. MO T I O N DE T EC T MOD E L E VE L AR EA E D I T . . AL ARM T I M E DE MON S TRA T I ON . . 1. Select the item AREA EDIT on the MOTION DETECT screen. 2. Press the SET button. OFF NORMAL 10s The setting screen is brought up. 3. MOTION DETECT screen Select the area not subject to detection using the button. The area flashing ON and OFF in black and white moves. flash 4. Press the SET button.
OTHERS Installing the ferrite core To retain electromagnetic compatibility, use the ferrite cores provided when connecting to the lens or the power source. Video-iris lens (or galvanometnc-iris lens) Wind twice H ALC LEVEL Av Pk L IRIS VIDEO DC Ferrite core Notes: ● Install the ferrite cores within 50 mm of the camera-side connectors. (Fasten the ferrite core with the wire clamp provided.) For lens connection: Pass the lens cable through the ferrite core twice and connect it to the camera.
Image pickup device: Synchronization method : Scanning frequency: Resolution: VIDEO OUT: Y/C OUT: 1/3 type IT CCD, 768 (H) × 494 (V) Internal, Line lock, Full Genlock (H) 15.734 kHz, (V) 59.94 Hz 480 TV lines (H) Composite video signal 1 V (p-p), 75Ω (BNC) (4-pin) Y: 1V(p–p), 75Ω C: 0.286V(p–p), 75Ω Video S/N ratio: 50 dB (AGC OFF) Minimum required illumination: 0.8 lx (50%, F1.2, AGC 20 dB) 0.4 lx (25%, F1.2, AGC 20 dB) 0.025 lx (50%, F1.
ADC770 COLOR VIDEO CAMERA Please visit our website for more information www.americandynamics.net ©2004 Sensormatic Electronics Corporation. Product specifications subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies. e03_adc770(23_40)e.