Installation Guide

ManualsBrandsAmerican Dynamics ManualsCamera & PhotoDome SDU8E Color Camera Module

Table Of Contents

SPEEDDOME ULTRA 8 CAMERA DOME 8200-0600-03, REV. F1

INSTALLATION AND SERVICE GUIDE

1 OF 30

SpeedDome Ultra 8

Camera Dome

Installation and Service Guide

Figure 1. SpeedDome Ultra Camera Dome

Camera Dome Product Codes

Product

Description

ADSDU822N

22X, N, VERSION 1.00, BLACK

ADSDU822P

22X, P, VERSION 1.00, BLACK

ADSDU822WN

22X, N, VERSION 1.00, WHITE

ADSDU822WP

22X, P, VERSION 1.00, WHITE

ADSDU835N

35X, N, DAY/NIGHT, VERSION 1.00, BLACK

ADSDU835P

35X, P, DAY/NIGHT, VERSION 1.00, BLACK

ADSDU835WN

35X, N, DAY/NIGHT, VERSION 1.00, WHITE

ADSDU835WP

35X, P, DAY/NIGHT, VERSION 1.00, WHITE

Contents

About this Guide .................................................... 1

About the Camera Dome ....................................... 2

Cable Requirements .............................................. 7

Install/Removal Tool for Base with I/O Board ........ 8

Power-Up Routine.................................................. 8

Synchronizing Domes ............................................ 8

Diagnostic LEDs .................................................... 8

Warnings and Cautions ......................................... 9

Indoor Installation................................................. 10

Using the Install/Removal Tool ............................ 14

Troubleshooting Indoor Domes ........................... 16

Parts List for Authorized Users ............................ 25

Specifications-Indoor Dome ................................. 27

Declarations ......................................................... 29

Appendix A: Vicon Wiring Configurations ............ 30

About this Guide

This guide explains how to connect the camera

dome to a mounting base and how to service it.

It does not explain how to:

 Determine a mounting location for the camera

dome. The mounting location is determined by

customer requirements; therefore, this

information is provided separately.

 Attach the mounting base. See information

shipped with the base.

 Assemble housings and structures used with

this camera dome. See information shipped with

the housing and structure.

 Program the camera dome. See operator's

guide shipped with the dome.

Mounting

Base

Housing

Eyeball

Summary of content (30 pages)

PAGE 1
Contents SpeedDome Ultra 8 Camera Dome About this Guide .................................................... 1 About the Camera Dome ....................................... 2 Cable Requirements .............................................. 7 Install/Removal Tool for Base with I/O Board ........ 8 Power-Up Routine.................................................. 8 Synchronizing Domes ............................................ 8 Diagnostic LEDs ....................................................
PAGE 2
Figure 2. Mounting base and housing and eyeball assembly About the Camera Dome The SpeedDome Ultra 8 camera dome (Figure 1):  Mounts indoors, or outdoors (with accessory outdoor enclosure)  Communicates with the video controller over a SensorNet 485, RS-422, Manchester, or UTC (up-the-coax) network  Consists of a mounting base, housing, and rotating eyeball assembly.
PAGE 3
Tile Ceilings Indoor Ceiling/Wall Mounting (Optional) RHIUFB The camera dome attaches to one of the following optional indoor mounting structures (Figure 4). RHIUAB Sheet Rock, Concrete, Plaster or Wood Ceilings RHIUTH RHIUHC RHIUFB RHIUPNDT† RHIU2X2M* Top hat housing with trim ring. This housing attaches to a ceiling or to most indoor mounting structures. A trim ring and optional magnetic bubble provide concealment. Optional bubbles: RUCLR (clear), RUSLV (silver), RUSMK (smoked), or RUGLD (gold).
PAGE 4
Figure 4. Indoor mounting structures (optional) RHIUFB, RHIUAB RHIUHC RHIU2X2 RHIU2X2P (with options) RHIUIBM (with options) RHIUTH ADSDUPIHC ADSDUPIHS ADSDUPIVRC ADSDUPIVRS ADSDUPIHC ADSDUPIHS ADSDUPIVRC ADSDUPIVRS RD500A RHIUTH Vandal-Resistant Bubble Vandal-Resistant Bubble RHIUTH RD500A RHIUCM RHIUPNDT RHIULWM (with option) RHIUTR RHIU3X3 RHIU4X4 SPEEDDOME ULTRA 8 CAMERA DOME INSTALLATION AND SERVICE GUIDE ADSDUCLR ADSDUSMK RHIUTH 8200-0600-03, REV.
PAGE 5
Outdoor Mounting (Optional) SpeedDome Housing Adapter Bracket (Optional) Note: This document does not include installation and service instructions for the AD outdoor housing. These instructions are supplied with the housing. An RHSDA adapter bracket (Figure 6) enables the dome to fit into SpeedDome indoor housings (RD500A). Locking pins in the bracket enable the dome to swing out for servicing or removal.
PAGE 6
ROENDC end cap Figure 7. Outdoor mounting structures (optional) Note: Housing is shown for reference only. RHOTR over roof mount comes with the ROENDC end cap (shown with RHOTRF bracket) RHOWPA pole mount comes with the ROENDC end cap RHOSW/RHOLW wall mount comes with the ROENDC end cap RHOPN pendant mount RHOSW RHOLW RHOWCA corner bracket only (shown with RHOLW mount) SPEEDDOME ULTRA 8 CAMERA DOME INSTALLATION AND SERVICE GUIDE 8200-0600-03, REV.
PAGE 7
Note: Typically, distances are used that provide a 15% margin between nominal and low line conditions. For example, if the nominal voltage is 120Vac, restrict cable length to that associated with 100Vac (0.85 x 120). Cable Requirements Data Cable The table below shows requirements for SensorNet, RS-422, and Manchester networks. For more information about communication protocols and cable networks, see Communication Protocols and Cable Networks, 8000-2573-19.
PAGE 8
Install/Removal Tool for Base with I/O Board Power-Up Routine After power is connected to the dome, the dome performs the following homing routine. The install/removal tool (Figure 8) enables you to connect or disconnect the housing and eyeball assembly from the mounting base, and to attach/detach skirts and bubbles from a top-hat housing, without the need for a ladder. The tool attaches to a telescopic pole (purchased separately). See page 14.
PAGE 9
The power supply can be obtained through Sensormatic or through another source where the provider can furnish the verification. This is required to assure electrical safety in the product. Warnings and Cautions Please review the following warnings and cautions before you begin installation or service. Stromanforderungen in der EU: Dieses Produkt wird mit 24 V Wechselstrom betrieben. In der EU ist es für den Betrieb durch eine begrenzte Stromquelle vorgesehen.
PAGE 10
Referring to Figure 9: Indoor Installation 1. Set the termination jumper E1 according to the dome’s position in the communications line. This section explains how to connect the housing and eyeball assembly to a mounting base. Position of dome in communications line… Items You Will Need Between other devices End of communications line You should have on hand the following tools and parts: Off 1-2 2.
PAGE 11
SensorNet data connections Pin Color Designation 5. Connect the alarm input cable, if used, to the TB3 connector. 1-4 — Pin Color 5 Orange SensorNet (unshielded) 1 — Alarm 1 input (3.5mA sink) 6 Yellow SensorNet (unshielded) 2 — Alarm 2 input (3.5mA sink) 3 — Alarm 3 input (3.5mA sink) 4 — Alarm 4 input (3.5mA sink) 5 — Ground 6 — Ground Not used. Figure 9. Electrical connections Designation 6. Connect power to the TB4 connector.
PAGE 12
Figure 10.
PAGE 13
11. Connect the housing and eyeball assembly to the base (Figure 12) by aligning the cap and base tabs, and then turning the housing clockwise until you hear a click. Note: The base has a florescent arrow and dot. Once the housing is secured, only the florescent dot will be seen. Note: Tabs on the base and cap have small holes that align once the base and cap are locked. If required, insert the security pin supplied (part number 2869-0037-01) through the holes.
PAGE 14
TO CONNECT DOME: Using the Install/Removal Tool 1. Insert the dome "eyeball down" into the tool's receptacle. Fins on the dome mate with slots in the tool. Use the fins to properly align the dimple at top of the dome with the label on the tool. CAUTION: Do not use this tool to connect the dome to the standard base (without I/O board) CAUTION: Use of the security pin prevents the use of the install/removal tool.
PAGE 15
Figure 13. How to use the install/removal tool Skirt or Bubble Attachment/Detachment A B Catch notch and pull down C Snap tool into pole Attachment Detachment Dome Connection (Reverse the steps to disconnect) Line up Line up D Turn until you feel a click B C SPEEDDOME ULTRA 8 CAMERA DOME INSTALLATION AND SERVICE GUIDE E 8200-0600-03, REV.
PAGE 16
Troubleshooting Indoor Domes CAUTION: This troubleshooting section is for indoor camera domes only! To troubleshoot outdoor domes, see the installation and service guide shipped with the outdoor housing. This chapter contains information on:  Routine troubleshooting  Detailed troubleshooting  Disassembling the dome. IMPORTANT! 1. Try routine troubleshooting first! Use this procedure to isolate the problem without disassembling the housing and eyeball assembly (the I/O board is field repairable).
PAGE 17
3. Detach the dome from its base. Are the address switches set correctly? Figure 14. I/O board connector and jumper locations YES If dome still doesn't respond, contact your sales representative for repair instructions. If you must repair the dome, see ―Detailed Troubleshooting‖ on page 18. NO Set correct address and reattach housing and eyeball assembly. 4. Isolate the problem to the housing/eyeball assembly or base by attaching dome to another base.
PAGE 18
8. If using RS-422 network and an I/O board is used, check comm. line connections by pressing and holding data test switch SW1 (Figure 15) and observing nearby red (CR12) and green (CR13) LEDs. These LEDs indicate the following: 9. Check the spring finger connector on the I/O board by connecting a known good dome to the base to verify contact between the spring fingers and the CPU board (under cap). Does dome produce video and respond to commands? Constant green, Blinking red Comm. line correctly wired.
PAGE 19
Procedure Disassembling the Dome Choose a, b, c, d or e to determine if the problem is a cable connection or major component. CAUTION: Once disassembled, parts of dome housing and eyeball assembly are "extremely fragile" and may break. Use extreme care! a. Dome functions but does not pan. On the power supply board, is the pan motor ribbon cable attached to connector P2 and is the metal side of its fingers towards the contacts of connector? YES Replace the power supply board.
PAGE 20
Removing the CPU Board Removing the P/S Board CAUTION: Electrostatic-sensitive device. Use a ground strap when handling CPU board. CAUTION: Electrostatic-sensitive device. Use a ground strap when handling power supply board. Referring to Figure 16. Referring to Figure 17. 1. Remove cap. 1. Remove three Phillips screws holding the cap, then "gently" lift the cap (this will unplug the CPU board from the power supply).
PAGE 21
Removing the Pan Motor Removing the Slot Covers Referring to Figure 18. 1. Gently swivel eyeball to totally expose one of two slot covers (Figure 19). 1. Perform procedure "Removing the P/S Board" (page 20). CAUTION: Swiveling fast can damage gears. 2. Remove pan motor. 2. Insert small, thin-bladed screwdriver into space between cover and eyeball. a. Lift the motor housing up as shown to disengage the motor from the pan gear. 3. Gently pry off slot cover. b.
PAGE 22
Removing the Camera Detaching the Eyeball 1. Perform procedure "Removing the Slot Covers" (page 21). 1. Perform procedure "Removing the Slot Covers" (page 21). 2. Remove ribbon cable from camera (Figure 20). 2. Perform procedure "Removing the Camera" (this page). Swivel camera yoke to expose camera connector. Then, using a small slotted screwdriver, 1) gently pry camera connector loose from camera, and 2) pull it down through cable tie wrap. 3. Detach the eyeball from the housing (Figure 22). a.
PAGE 23
Removing the Camera/Lens Board The following steps refer to Figure 26. 1. Perform procedure "Removing the Slot Covers" (page 21). 6. Access camera/lens board. To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly. 2. Perform procedure "Removing the Camera" (page 22). 3. Perform procedure "Detaching the Eyeball" (page 22). 7. Remove cables from camera/lens board. 4. Separate the yoke brackets (Figure 24). a. Small amber ribbon cable is from tilt motor.
PAGE 24
6. Access the tilt motor. Removing the Tilt Motor To do this, loosen the captive retaining screw holding the tilt cable assembly in place and gently remove the assembly. 1. Perform procedure "Removing the Slot Covers" (page 21). 2. Perform procedure "Removing the Camera" (page 22). 7. Remove the tilt motor (Figure 29). Lift the motor housing up as shown to disengage the motor from the tilt gear. Then pull the motor bracket towards the outside of the cable/tilt assembly to remove the motor. 3.
PAGE 25
Eyeball Assembly Parts List for Authorized Users Parts can be ordered by authorized users only. To become authorized, contact your sales representative. Parts in following tables and shown in Figure 30 are listed for clarity and not all can be ordered. Parts that can be ordered are subject to change based on design improvements and availability. Key Description Part Number 19 Cable Assy.
PAGE 26
Figure 30. Base, housing, and eyeball assembly Housing Assembly (0404-0306-01/-02 Base Assembly with I/O Board* * ADSDUIOB / ADSDUIOBW 5 6 1 4 2 7 8 3 9 10 11 12 13 Housing and Eyeball Assy., SpeedDome Ultra 8 (0101-0150-xx) 14 15 16 17 18 Eyeball Assy.
PAGE 27
Surge Protection: Specifications-Indoor Dome Design tolerance .................. 16-36Vac, 50/60Hz Video output ..........................Low capacitance Zener suppressor 6.5V, 1500W Operational Power line .............................TVS rated at 60V, 1.5 joules, 250A 8/20µs impulse Pan/Tilt: Manual pan speed .................. 0.25°-100° per second (scaled to zoom position) RS-422 ..................................TVS rated at 9.8V/1A, 20V/25A, 500W, 8/20µs impulse Manual tilt speed ...............
PAGE 28
22X Camera 35X Day/Night Camera Type ............................ Interline transfer 1/4in CCD array Type ........................... Interline transfer 1/4in CCD array Scanning area ................................ 3.2 (H) x 2.4 (V) mm Scanning area ................................ 3.2 (H) x 2.4 (V) mm Scanning system .........................................2:1 interlace Scanning system ......................................... 2:1 interlace Horizontal resolution ..........................
PAGE 29
Field-of-View Formulas: 3.2mm* x distance from camera (m) Focal length (mm) x Digital Zoom 2.4mm** x distance from camera (m) Focal length (mm) x Digital Zoom Other Declarations = Horizontal view (m) = Vertical view (m) * Horizontal scanning area of pickup device (mm) in camera. ** Vertical scanning area of pickup device (mm) in camera. Example: Wide angle view with lens at 6mm and viewed object at 10m. 3.2mm x 10m 6mm 2.4mm x 10m 6mm = 5.
PAGE 30
Appendix A: Vicon Wiring Configurations In Vicon systems where domes support loop through, daisy chain the SpeedDome Ultra 8 domes off the last Vicon dome in the communications chain. Figure 31.