Illustra Flex Series 1MP & 3MP Outdoor Dome Quick Start Guide 8200-1027-10 B0
Illustra Flex 1MP & 3MP Outdoor Dome Notice Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.
Illustra Flex 1MP & 3MP Outdoor Dome Table of Contents WARNING ........................................................................................................................................................ 4 Preface ............................................................................................................................................................. 5 1. Product Overview .........................................................................................................
Illustra Flex 1MP & 3MP Outdoor Dome WARNING This unit operates at AC 24V/ PoE. Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty. To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth.
Illustra Flex 1MP & 3MP Outdoor Dome Preface This user manual is designed as a reference for the installation and manipulations of the unit including the camera’s features, functions, and detailed explanation of the menu tree. The reader is supposed to be able to get following information in the manual. Product Overview: the main functions and system requirements of the unit. Installation and Connection: instructions on unit installation and wire connections.
Illustra Flex 1MP & 3MP Outdoor Dome 1. Product Overview 1.
Illustra Flex 1MP & 3MP Outdoor Dome TABLE 1-1: PICTORIAL INDEX DEFINITION Index # Name 1 Camera bottom case 2 Tilt adjustment bracket and thumbnuts, notches(X2), 3 IR board 4 Loosen the screw to take off camera housing 5 Camera top case 6 Dome cover FIGURE 1-3: PIN DEFINITIONS 1/2 TABLE 1-2: PIN DEFINITIONS 1/3 DEFAULT RESET return to factory default by press button for 5 seconds system restart 7
Illustra Flex 1MP & 3MP Outdoor Dome FIGURE 1-4: PIN DEFINITIONS 2/2 Note Connectors and field wiring terminal for external Class 2 circuits provided with marking indicating minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field wiring terminals.
Illustra Flex 1MP & 3MP Outdoor Dome 2. Installation and Connection 2.1 Unpack Everything Check everything in the packing box matches to the order form and the packing slip. In addition to this manual, items below are included in the packing box. One Network IR vandal dome Camera 2-pin terminal block for power input, and 8-pin terminal block for alarm input/output One CD containing Illustra Connect, user manual and quick installation guide.
Illustra Flex 1MP & 3MP Outdoor Dome 2.2.2 Disassembling the Camera Gently remove the screw to take off camera housing (3). Set the camera housing (4) aside. FIGURE 2-1: DISASSEMBLING THE CAMERA 2.2.3 Connecting the wires 1. Connect the power cable to the power plugs with one of the following options. Inset power cable for AC 24V, Connect 24 V (~) cables to terminals ~AC 24V. PoE: Connect the RJ-45 jack to a PoE compatible network device that supplied power through the Ethernet cable.
Illustra Flex 1MP & 3MP Outdoor Dome 2. Insert Audio cable and alarm cable to the unit, and connect the network cable to the RJ-45 terminal of a switch. FIGURE 2-2: CONNECTING THE WIRES 3. Connected the wiring then place the camera to a proper position by pushing the button.
Illustra Flex 1MP & 3MP Outdoor Dome 2.2.4 Mounting the camera Place the mounting template sticker (supplied) on the mounting surface and mark three holes according to the mounting template sticker. Then fasten the anchors to the mounting surface with screws. Next, secure the unit bottom case (1) to the wall/ceiling with tapping screws as supplied and adjust the view angle (zoom, focus, and horizontal rotation). FIGURE 2-4: MOUNTING THE CAMERA Refer to figure 2-5.
Illustra Flex 1MP & 3MP Outdoor Dome (Optional) 4S Electrical junction box 1. Secure the mounting kit (optional) to 4S Electrical box using 2 appropriate screws. 2. Secure the unit case to mounting kit using 2 appropriate screws. 3. Tuck the cables in the 4S Electrical box. 4. Adjust the view angles (zoom, focus, and horizontal rotation). 5. Attach the unit housing. 6. Turn the power on after installed the unit.
Illustra Flex 1MP & 3MP Outdoor Dome 2.2.5 Adjusting the camera position The unit has three axes for positioning. While screening the picture on the monitor, adjust the position by procedures below. Pan Adjustment (A): for wall mount and tilted ceiling rotate the lens base (360° maximum) until satisfied with the field of view. Horizontal Rotation (B): rotate 3D assembly in the base, but do not turn assembly more than 360° as this may have the internal cables twisted, disconnected, or broken.
Illustra Flex 1MP & 3MP Outdoor Dome 2.2.6 Locking the camera Use soft, lint -free cloth to wipe the dome cover and remove fingerprints. Attach camera housing. Turn the power on after you have installed the unit. 2.2.7 Network Topology The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with Ethernet RJ-45 network interface.
Illustra Flex 1MP & 3MP Outdoor Dome 2.2.8 System Requirements Below table lists the minimum requirement to implement and operate a Illustra Flex Outdoor Dome. TABLE 2-1: SYSTEM REQUIREMENTS System Hardware CPU Intel Pentium 4 2.
Illustra Flex 1MP & 3MP Outdoor Dome 2.3 Connection 2.3.1 Default IP address Since this is a network-based unit, an IP address must be assigned at the very first. The unit’s default IP address is 192.168.1.168 and sub mask is 255.255.255.0. However, if you have a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server so that you don’t need to change the camera’s IP address. But be sure to enable DHCP in “Network/Basic setting” 2.3.
Illustra Flex 1MP & 3MP Outdoor Dome 2.3.2.2 Viewing Preparation Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these steps to enable the display. 1. 2. Enable Cookies as instructions below In Internet Explorer, click Internet Options on the Tools menu. On the Privacy tab, move the settings slider to Low or Accept All Cookies. Click OK.
Illustra Flex 1MP & 3MP Outdoor Dome Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows: 【Download signed ActiveX controls】 Prompt (recommended) 【Download unsigned ActiveX controls】 Prompt 【Initialize and script ActiveX not marked as safe for scripting】 Prompt FIGURE 2-12: SECURITY SETTINGS 2/4 【Automatic prompting for ActiveX controls】 Enable FIGURE 2-13: SECURITY SETTINGS 3/4 19
Illustra Flex 1MP & 3MP Outdoor Dome 【Run ActiveX controls and plug-ins】 Enable 【Script ActiveX controls marked safe for scripting*】 Enable FIGURE 2-14: SECURITY SETTINGS 4/4 Press OK to save the settings. Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect. Type your setting IP address into the browser. Then you should be able to see the camera image screen. 2.