Specifications

ManualsBrandsAmerican Dynamics ManualsSecurity CameraRAS917LS-1

SPEEDDOME ULTRA VII CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0184-01, REV. A1)

1 of 41

SpeedDome

Ultra VII

Camera Dome

Installation and Service Guide

Figure 1. SpeedDome Ultra VII camera dome

Camera Dome Product Codes

Product Description

RAS915LS BW, 60HZ, 22X, NO BASE, BLACK

RAS915LSI BW, 60HZ, 22X, I/O BASE, BLACK

RAS915LSP BW, 60HZ, 22X, STD BASE, BLACK

RAS915LS-1 BW, 50HZ, 22X, NO BASE, BLACK

RAS915LSI-1 BW, 50HZ, 22X, I/O BASE, BLACK

RAS915LSP-1 BW, 50HZ, 22X, STD BASE, BLACK

RAS916LS COLOR, 60HZ, 22X, NO BASE, BLACK

RAS916LSI COLOR, 60HZ, 22X, I/O BASE, BLACK

RAS916LSP COLOR, 60HZ, 22X, STD BASE, BLACK

RAS916WLS COLOR, 60HZ, 22X, NO BASE, WHITE

RAS916WLSI COLOR, 60HZ, 22X, I/O BASE, WHITE

RAS916WLSP COLOR, 60HZ, 22X, STD BASE, WHITE

RAS916LS-1 COLOR, 50HZ, 22X, NO BASE, BLACK

RAS916LSI-1 COLOR, 50HZ, 22X, I/O BASE, BLACK

RAS916LSP-1 COLOR, 50HZ, 22X, STD BASE, BLACK

RAS916WLS-1 COLOR, 50HZ, 22X, NO BASE, WHITE

RAS916WLSI-1 COLOR, 50HZ, 22X, I/O BASE, WHITE

RAS916WLSP-1 COLOR, 50HZ, 22X, STD BASE, WHITE

RAS917LS DAY/NIGHT, 60HZ, 23X, NO BASE, BLACK

RAS917LSI DAY/NIGHT, 60HZ, 23X, I/O BASE, BLACK

RAS917LSP DAY/NIGHT, 60HZ, 23X, STD BASE, BLACK

RAS917WLS DAY/NIGHT, 60HZ, 23X, NO BASE, WHITE

RAS917WLSI DAY/NIGHT, 60HZ, 23X, I/O BASE, WHITE

RAS917WLSP DAY/NIGHT, 60HZ, 23X, STD BASE, WHITE

RAS917LS-1 DAY/NIGHT, 50HZ, 23X, NO BASE, BLACK

RAS917LSI-1 DAY/NIGHT, 50HZ, 23X, I/O BASE, BLACK

RAS917LSP-1 DAY/NIGHT, 50HZ, 23X, STD BASE, BLACK

RAS917WLS-1 DAY/NIGHT, 50HZ, 23X, NO BASE, WHITE

RAS917WLSI-1 DAY/NIGHT, 50HZ, 23X, I/O BASE, WHITE

RAS917WLSP-1 DAY/NIGHT, 50HZ, 23X, STD BASE, WHITE

Contents

Contents ..................................................................1

About this Guide......................................................1

About the Camera Dome ........................................2

Cable Requirements ...............................................8

Install/Removal Tool for Base with I/O Board .........9

Power-Up Routine...................................................9

Synchronizing Domes .............................................9

Diagnostic LEDs......................................................9

Warnings and Cautions.........................................10

Indoor Installation ..................................................12

Using the Install/Removal Tool .............................20

Troubleshooting Indoor Domes.............................22

Parts List for Authorized Users ............................34

Specifications-Indoor Dome ..................................36

Specifications-22X Camera...................................37

Specifications-23X Camera...................................38

Declarations ..........................................................39

Appendix A: Checking Power/Data on Std Base ..40

About this Guide

This guide explains how to connect the camera

dome to a mounting base and how to service it.

It does not explain how to:

· Determine a mounting location for the camera

dome. The mounting location is determined by

customer requirements; therefore, this

information is provided separately.

· Attach the mounting base. There are two types

of mounting bases. See information shipped

with the base.

· Assemble housings and structures used with

this camera dome. See information shipped with

the housing and structure.

· Program the camera dome. See operator's

guide shipped with the dome.

Mounting

Base

Housing

Eyeball

Summary of content (41 pages)

PAGE 1
SpeedDome Ultra VII Camera Dome Contents ® Contents ..................................................................1 About this Guide......................................................1 About the Camera Dome ........................................2 Cable Requirements ...............................................8 Install/Removal Tool for Base with I/O Board .........9 Power-Up Routine ...................................................9 Synchronizing Domes .......................................
PAGE 2
· Eyeball. With a diameter of 120mm (4.75"), the eyeball contains a camera, tilt motor, and associated electronics. The eyeball enables the camera to pan and tilt to track a target moving in any direction even as it moves under the dome. About the Camera Dome The SpeedDome Ultra VII camera dome (Figure 1) comes in black or white finish (to blend into surrounding areas), mounts indoors or outdoors, and can communicate with the video controller over a SensorNet 485, RS422, or Manchester network.
PAGE 3
Indoor Ceiling Mounting Using hardware shipped with the base, the dome attaches directly to indoor ceilings made of sheet rock, wood, metal, or concrete (Figure 3), or to tile ceiling T-bars where they intersect (Figure 4). Figure 3. Surface mounting to hard ceilings Figure 4. Surface mounting to tile ceilings SPEEDDOME ULTRA VII CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0184-01, REV.
PAGE 4
Indoor Ceiling/ Wall Mounting (Optional) Structural I-Beams RHIUIB† I-beam mount Enables dome to suspend from an I-beam. The camera dome attaches to one of the following optional indoor mounting structures (Figure 5). Sheet Rock, Plaster or Wood Ceilings RHIUTH Tile Ceilings Top hat housing with trim ring This housing attaches to a ceiling or to most indoor mounting structures. A bubble and trim ring provide concealment. Optional bubbles: RUCLR (clear), RUSLV (silver), RUSMK (smoked), or RUGLD (gold).
PAGE 5
Figure 5. Indoor mounting structures (optional) RHIUFB RHIUAB RHIUHC RHIUIB RHIU2X2 RHPLA RHIU2X2P RHIUTH RHIUWM RHIUPNDT RHIUCM RHIUTR RHIU3X3 RHIU4X4 RUCLR RUSLV RUSMK RUGLD SPEEDDOME ULTRA VII CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0184-01, REV.
PAGE 6
Outdoor Mounting (Optional) SpeedDome Housing Adapter Bracket (Optional) Note: This document does not include outdoor installation and service instructions. For these instructions, see Installing the RHODUL Outdoor Housing, 8000-2573-04. An RHSDA adapter bracket (Figure 7) enables the dome to fit into SpeedDome indoor and outdoor housings. Locking pins in the bracket enable the dome to swing out for servicing or removal.
PAGE 7
RHOWPA pole mount Figure 8. Outdoor mounting structures (optional) RHOTR over roof mount (shown with RHOTRF bracket) RHOSW/RHOLW wall mount RHOSW PHOPN pendant mount RHOLW RHOWCA corner bracket (shown with RHOLW mount) SPEEDDOME ULTRA VII CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0184-01, REV.
PAGE 8
Note: Typically, distances are used that provide a 15% margin between nominal and low line conditions. For example, if the nominal voltage is 120Vac, restrict cable length to that associated with 100Vac (0.85 x 120). Cable Requirements Data Cable The table below shows requirements for SensorNet, RS422, and Manchester networks. For more information about communication protocols and cable networks, see Communication Protocols and Cable Networks, 8000-2573-19.
PAGE 9
Install/Removal Tool for Base with I/O Board Power-Up Routine After power is connected to the dome, the dome performs the following homing routine. The install/removal tool (Figure 9) enables you to connect or disconnect the housing and eyeball assembly from the base with I/O board, and to attach/detach skirts and bubbles to a top hat housing, without the need for a ladder. The tool attaches to a telescopic pole (purchased separately). See page 20. 1.
PAGE 10
! Warnings and Cautions Please review the following warnings and cautions before you begin installation or service. This dome runs on 24Vac. DO NOT connect line voltage to this dome. North America power requirements: In North America, this device is intended to be supplied from a Class 2 power supply. For outdoor installations, use Class 3 wiring techniques, liquidtight conduit, or liquid-tight pipe.
PAGE 11
CAUTIONS G When connecting the housing and eyeball assembly to an outdoor housing: G Do not run data and power cables adjacent to or in the same conduit as line voltage mains power. - Remove both slot covers to keep the camera from overheating. - Keep cables entering the housing away from the heater assembly. G SensorNet 485 networks require 22 AWG unshielded cable. Do not exceed 32 devices per cable run.
PAGE 12
Other Preparations Indoor Installation To ensure a smooth and successful installation, you must: This section explains how to connect the housing and eyeball assembly to a: · Mounting base with I/O board. · Have electrical work comply with latest national electrical code, national fire code, and all applicable local codes and ordinances. Items You Will Need · Coordinate work with other trades to avoid interference.
PAGE 13
Connecting to the Standard Mounting Base Figure 10. Setting address switches SW3 MSB This procedure explains how to connect the housing and eyeball assembly to a standard base. ! 0 WARNING: Ensure that ac power and electrical signals are off during wire connections! SW2 9 0 SW1 LSB 9 0 9 1. Set the dome address (Figure 10). Recessed at the top of housing and eyeball assembly are three rotary address switches. Address range is from 001 to 255, except for Manchester, which is 01 to 64.
PAGE 14
5. Connect the 9-pin plug (data and power) to the 9-pin receptacle (Figure 13). If using a Pelco Coaxitron or Panasonic UTC protocol, no data wires are connected, just power. 3. WITH POWER OFF, connect the video cable (Figure 12). a. Connect BNC of video micro coax cable 6003-0170-01 to BNC of video cable. CAUTION: DO NOT connect the 9-pin plug unless you have performed step 3 first! b. Feed cable through access hole in base. c.
PAGE 15
7. Connect the housing and eyeball assembly to the base (Figure 14). 6. Connect the 4-pin plug (alarm input/output) to the 4-pin receptacle (Figure 13). a. Feed the cable through the access hole in the base. a. Align the dimple on the cap of the dome with the rib on the mounting base. b. Connect alarm wires to the 4-pin plug (refer to chart below). b. Mate the housing and eyeball assembly to the base and turn it clockwise until you hear a click. c.
PAGE 16
Connecting to a Mounting Base with I/O Board RS422 data connections This procedure explains how to connect the housing and eyeball assembly to a mounting base with I/O board. WARNING: Ensure that ac power and electrical signals are off during wire connections! ! Pin Color Designation 1 Orange RS422 Data In High (+) 2 Green RS422 Data In Low (–) 3 Yellow RS422 Data Out High (+) 4 Brown RS422 Data Out Low (–) 5-6 — Not used.
PAGE 17
4. Connect the alarm output cable, if used, to the P3 connector. Pin Color 1 — 12Vdc (100mA max.) 2 — 12Vdc (100mA max.) 3 — Output P0 (40mA sync. max.) 4 — Output P1 (40mA sync. max.) 5 — Output P2 (40mA sync. max.) 6 — Output P3 (40mA sync. max.) 7 — Ground 8 — Ground 7. Reattach the I/O board. 8. Connect power to the base. Designation 9. Check LEDs on the I/O board to verify power and data are reaching the dome (Figure 16). a.
PAGE 18
Figure 17. Setting address switches 10. Set the dome address (Figure 17). Recessed at top of the housing and eyeball assembly are three rotary address switches. The address range is from 001 to 255, except for Manchester, which is 01 to 64. SW3 MSB Set switches from most significant bit (MSB) to least significant bit (LSB). For example: For address 166, set SW3 to 1, SW2 to 6, and SW1 to 6.
PAGE 19
11. Connect the housing and eyeball assembly to the base (Figure 18). a. Align the dimple on the cap of the dome with the rib on the mounting base. b. Mate the housing and eyeball assembly to the base and turn it clockwise until you hear a click. 12. Wait a few seconds for dome to begin its homing routine. The homing routine indicates that the address was placed into the dome memory and that the dome is ready for programming. Figure 18.
PAGE 20
TO CONNECT DOME: Using the Install/Removal Tool 1. Insert dome "eyeball down" into tool's receptacle. Fins on dome mate with slots in tool. Use fins to properly align dimple at top of dome with label on tool. CAUTION: Do not use this tool to connect the dome to the standard base. 2. Align label on tool with logo on I/O board in base. Push dome up into place.
PAGE 21
Figure 19. How to use the install/removal tool Skirt or Bubble Attachment/Detachment A B Catch notch and pull down. C Snap tool into pole. Attachment Detachment Dome Connection (reverse steps to disconnect) Line up Line up D Turn until you feel a click. B C E Do not use this tool to connect the standard base! SPEEDDOME ULTRA VII CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0184-01, REV.
PAGE 22
Items You Will Need Troubleshooting Indoor Domes You should have on hand the following items: · Phillips-head screwdriver CAUTION: This troubleshooting section is for indoor camera domes only! To troubleshoot outdoor domes, see installation and service manual shipped with the outdoor housing. · Small slotted screwdriver · 2.5mm (0.1") slotted screwdriver (for wire connections). Wider blade widths can damage connectors.
PAGE 23
Routine Troubleshooting Procedure Use this procedure if: Follow steps until the problem is corrected. · Dome does not respond to commands 1. Check video on monitor (a, b, or c). · Dome does not produce video a. No video? Go to step 2. · Quality of the video is poor b. Contrast or color off? · Dome has no lens control. YES Contact your sales representative for repair instructions. CAUTION: NO · DO NOT use this procedure if the dome functions but does not pan or tilt (see step 2 on page 22).
PAGE 24
6. Observe green power LED on I/O board (Figure 21). Is green LED off or not on steady? 4. Isolate problem to housing and eyeball assembly or base by attaching dome to another base with I/O board. Does dome display video or respond to commands? YES Problem is likely cable connections or I/O board if used. Go to step 5. YES Verify 24Vac cable is properly attached. If OK, replace I/O board or contact your sales representative for repair instructions.
PAGE 25
P1 connector (Manchester data) Pin Color 1-4 9. Check spring finger connector on I/O board by connecting housing and eyeball assembly to original base to verify contact between spring fingers and CPU board (under cap). Does dome produce video and respond to commands? Designation Not used. 5 Black Manchester (+) 6 White Manchester (–) YES Spring fingers may not have seated properly. Reconnect housing and eyeball assembly.
PAGE 26
Detailed Troubleshooting Procedure Use this procedure to determine if the problem is a simple cable connection or a major component. 1. Match symptom to one of the following criteria: - Dome functions but does not pan To perform this procedure, you must open the housing and eyeball assembly. Refer to "Disassembling the Dome" on page 27.
PAGE 27
Disassembling the Dome Removing the CPU Board CAUTION: Once disassembled, parts of dome housing and eyeball assembly are "extremely fragile" and may break. Proceed using extreme care! CAUTION: Electrostatic-sensitive device. Use a ground strap when handling CPU board. Referring to Figure 22. 1. Remove cap. This section explains how to remove the following parts from the camera dome. Remove three Phillips-head screws holding cap, then "gently" lift cap to one side. · CPU board, page 27 2.
PAGE 28
Removing the P/S Board Removing the Pan Motor CAUTION: Electrostatic-sensitive device. Use a ground strap when handling power supply board. Referring to Figure 24. Referring to Figure 23. 1. Perform procedure "Removing the CPU Board" (page 27). 1. Perform procedure "Removing the CPU Board" (page 27). 2. Perform procedure "Removing the P/S Board" (page 28). 2. Remove metal shield. 3. Remove pan motor. Lift motor housing up as shown (1) to disengage motor from pan gear.
PAGE 29
Removing the Slot Covers Removing the Camera 1. Gently swivel eyeball to totally expose one of two slot covers (Figure 25). 1. Perform procedure "Removing the Slot Covers" (page 29). CAUTION: Swiveling fast can damage gears. 2. Remove ribbon cable from camera (Figure 26). Swivel camera yoke to expose camera connector. Then, using a small slotted screwdriver, 1) gently pry camera connector loose from camera, and 2) pull it down through cable tie wrap. 2.
PAGE 30
Detaching the Eyeball Removing the Camera/Lens Board 1. Perform procedure "Removing the Slot Covers" (page 29). 1. Perform procedure "Removing the Slot Covers" (page 29). 2. Perform procedure "Removing the Camera" (this page). 2. Perform procedure "Removing the Camera" (page 29). 3. Detach eyeball from housing (Figure 28). 3. Perform procedure "Detaching the Eyeball" (page 30). a. Turn yoke to access tabs. One tab is more accessible than the other.
PAGE 31
The following steps refer to Figure 32. Removing the Tilt Motor 6. Access camera/lens board. 1. Perform procedure "Removing the Slot Covers" (page 29). To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly. 2. Perform procedure "Removing the Camera" (page 29). 7. Remove cables from camera/lens board. 3. Perform procedure "Detaching the Eyeball" (page 30). a. Small amber ribbon cable is from tilt motor.
PAGE 32
6. Access tilt motor. 8. Reverse steps to reassemble. To do this, loosen captive retaining screw holding tilt cable assembly in place and gently remove this assembly. CAUTION: When installing a new motor, be careful to properly mesh motor and tilt gears! Failure to do so can destroy both motor and tilt gear. Verify tilt gear turns freely! 7. Remove tilt motor (Figure 35). Lift motor housing up as shown to disengage motor from tilt gear.
PAGE 33
Updating/Reprogramming Dome Software Figure 36. Removing the flash memory chip CAUTION: This procedure involves extracting a flash memory chip, an electrostatic-sensitive device. Use a ground strap when handling the chip. To update or reprogram dome software: 1. Insert the chip extractor tool into the square access hole and squeeze the tool to extract the flash memory chip (Figure 36). 2. Reprogram the chip or replace it with a new one. 3.
PAGE 34
Eyeball Assembly Parts List for Authorized Users The following parts can only be ordered by authorized users. To become authorized, contact your sales representative. Parts in the tables below are shown in Figure 37. Parts lists Standard Base Assembly 27 Tilt Motor 3501-0018-01 28 Slot Cover (No Lens)* 0500-8037-01/-02 29 Yoke, Camera 0500-7258-01 30 Camera/Lens PC Board 0301-0953-01 31 Bearing Assy., Lens Carriage 2510-0038-01 32 Yoke Bracket (Qty. 2) 0500-8038-01/-02 33 Cable Assy.
PAGE 35
Figure 37. Base, housing, and eyeball assembly Standard Base Assembly* * RUPTB/RUWPTB ** RUIOB/RUWIOB Housing Assembly (0404-0078-01/-02) Base Assembly with I/O Board** 13 14 9 1 2 10 3 11 4 12 5 15 16 17 18 19 20 21 6 7 8 Housing and Eyeball Assy. Assy.
PAGE 36
Program Storage .................... 256 Kbytes of Flash memory Specifications-Indoor Dome Data Storage .......................... 128 Kbytes of SRAM Menu Languages.................... English, French, German, Spanish, Italian, and Portuguese Operational Pan/Tilt: * Using AD2083-02A Manual Pan Speed ............. 0.2°-100° per second (scaled to zoom position) Electrical Manual Tilt Speed............... 0.25°-100° per second (scaled to zoom position) Input Voltage ........................
PAGE 37
Environmental PAL: Effective Pixels ..................752 (H) x 582 (V) pixels Operating Temperature.........–10° to 50°C (14° to 122°F) Scanning ...........................625 lines, 50 fields, 25 frames Relative Humidity ..................0 to 95% non-condensing Storage Temperature ............. –20°C to 65°C (–4°F to 149°F) Horizontal ..........................15.625kHz Vertical ..............................50Hz Mechanical Monochrome Camera Only Horizontal Resolution ........
PAGE 38
Field-of-View Formulas: Specifications-23X Camera 3.2mm* x distance from camera (m) Type .................................. Interline transfer 1/4" CCD array Scanning Area .................. 3.2 (H) x 2.4 (V) mm Focal length (mm) 2.4mm** x distance from camera (m) Focal length (mm) Scanning System .............. 2:1 interlace Video Out .......................... 1.0 Vp-p/75 ohms composite = Horizontal view (m) = Vertical view (m) * Horizontal scanning area of pickup device (mm) in camera.
PAGE 39
Other Declarations Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
PAGE 40
Figure 38. Cable connections (Manchester requires separate cables for data and power) Appendix A: Checking Power and Data for Domes Using the Standard Base Check LEDs to verify that power and data are reaching the dome (Figure 38). IMPORTANT! To view the LEDs, you will need to detach the dome from its base. To prevent damage to the dome, hold the dome by its housing, not its eyeball assembly. a. If the power LED (CR33) on the I/O board glows green, then ac power is connected. b.
PAGE 41
SensorNet: After approximately 20 seconds, the three LEDs do the following: RS422: Set the domes address switches to 900 test mode, then apply power. After approximately 20 seconds, the three LEDs do the following: 3 Red Green Yellow Control3 Possible Cause Mostly Off, Blinking On Mostly Off, Blinking On Rapidly Blinking Yes RX+ (pin 6) and RX– (pin 7) correctly wired. Mostly Off, Blinking On Mostly Off, Blinking On Rapidly Blinking No Wire to RX+ (pin 6) not connected.