User Manual

INSTALLATION INSTRUCTIONS CONTEMPO
POST TOP LUMINAIRE 245 LED SERIES
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A72882 REV C
©2013 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72882
WARNING
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
!
CAPTIVE SCREW
CAPTIVE SCREW
DOOR
DOOR
SERVICE LEADS (105
SERVICE LEADS (105°
C)
C)
TERMINAL BLOCK
TERMINAL BLOCK
HOOD LOCKING SCREW
HOOD LOCKING SCREW
(HIDDEN) HINGE
(HIDDEN) HINGE
SET SCREW
SET SCREW
WARNING
ENSURE THAT ALL POWER IS
DISCONNECTED PRIOR TO WIRING
!
TM
MOUNTING:
MOUNTING:
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
EXTERIOR DIAMETER BETWEEN 2.375” AND 3.125“
EXTERIOR DIAMETER BETWEEN 2.375” AND 3.125“
1. REMOVE ACCESS DOOR BY LOOSENING CAPTIVE SCREW.
1. REMOVE ACCESS DOOR BY LOOSENING CAPTIVE SCREW.
2. PULL SERVICE LEADS THROUGH BASE ASSEMBLY AND
2. PULL SERVICE LEADS THROUGH BASE ASSEMBLY AND
OUT ACCESS DOOR OPENING AS SHOWN.
OUT ACCESS DOOR OPENING AS SHOWN.
NOTE: IF UNIT IS PRE-WIRED, FEED THE SUPPLIED
NOTE: IF UNIT IS PRE-WIRED, FEED THE SUPPLIED
PRE-WIRE THROUGH THE POST TOP AND DOWN THE POLE.
PRE-WIRE THROUGH THE POST TOP AND DOWN THE POLE.
3. ORIENT THE UNIT SO THE DOOR IS TO THE STREET SIDE.
3. ORIENT THE UNIT SO THE DOOR IS TO THE STREET SIDE.
4. TIGHTEN THE THREE MOUNTING SET SCREWS.
4. TIGHTEN THE THREE MOUNTING SET SCREWS.
CAUTION
DO NOT TIGHTEN SET SCREWS
BEYOND 15 ft-lb. TORQUE.
!
WIRING:
WIRING:
NOTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS
NOTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS
SUPPLIED WITH PRE-WIRE.
SUPPLIED WITH PRE-WIRE.
1. PULL UP THE TERMINAL BLOCK COVER.
1. PULL UP THE TERMINAL BLOCK COVER.
2. CONNECT SERVICE LEADS TO TERMINAL BLOCK. REFER
2. CONNECT SERVICE LEADS TO TERMINAL BLOCK. REFER
TO WIRING DIAGRAM ON INSIDE OF ACCESS DOOR.
TO WIRING DIAGRAM ON INSIDE OF ACCESS DOOR.
3. PUSH DOWN THE TERMINAL BLOCK.
3. PUSH DOWN THE TERMINAL BLOCK.
4. REPLACE ACCESS DOOR AND SECURE WITH CAPTIVE
4. REPLACE ACCESS DOOR AND SECURE WITH CAPTIVE
SCREW.
SCREW.
HOOD:
HOOD:
1. INSTALL HOOD ONTO BASE ASSEMBLY BY INSERTING
1. INSTALL HOOD ONTO BASE ASSEMBLY BY INSERTING
HINGE BAR OF THE BASE INTO HINGE BRACKET ON UNDER
HINGE BAR OF THE BASE INTO HINGE BRACKET ON UNDER
SIDE OF THE HOOD. SWING HOOD OVER AND INTO PLACE.
SIDE OF THE HOOD. SWING HOOD OVER AND INTO PLACE.
NOTE: IF THE UNITS INCLUDE PHOTOCONTROL CONNECT
NOTE: IF THE UNITS INCLUDE PHOTOCONTROL CONNECT
THE QUICK CONNECTORS BEFORE CLOSE THE HOOD.
THE QUICK CONNECTORS BEFORE CLOSE THE HOOD.
2. FASTEN HOOD LOCKING SCREW.
2. FASTEN HOOD LOCKING SCREW.
PHOTOCONTROL:
PHOTOCONTROL:
NOTE: NO TOOLING IS NECESSARY FOR THE PHOTOCONTROL
NOTE: NO TOOLING IS NECESSARY FOR THE PHOTOCONTROL
INSTALLATION OR ADJUSTMENT.
INSTALLATION OR ADJUSTMENT.
1. LIFT AND ROTATE THE RECEPTACLE SO THAT THE ARROW
1. LIFT AND ROTATE THE RECEPTACLE SO THAT THE ARROW
ON THE TOP POINTS NORTH. RELEASE THE RECEPTACLE.
ON THE TOP POINTS NORTH. RELEASE THE RECEPTACLE.
2. PLUG THE PHOTOCONTROL INTO THE RECEPTACLE AND
2. PLUG THE PHOTOCONTROL INTO THE RECEPTACLE AND
TWITS IT CLOCKWISE UNTIL IT LOCKS INTO POSITION.
TWITS IT CLOCKWISE UNTIL IT LOCKS INTO POSITION.
MAINTENANCE:
MAINTENANCE:
CLEAN THE FIXTURE WITH MILD SOAP OR HOUSEHOLD TYPE
CLEAN THE FIXTURE WITH MILD SOAP OR HOUSEHOLD TYPE
DETERGENT. DO NOT USE ACID OR CAUSTIC CLEANERS.
DETERGENT. DO NOT USE ACID OR CAUSTIC CLEANERS.
THIS DEVICE COMPLIES WITH PART 18 THE FCC RULES BUT
THIS DEVICE COMPLIES WITH PART 18 THE FCC RULES BUT
MAY CAUSE INTERFERENCE WITH CORDLESS AND CELL
MAY CAUSE INTERFERENCE WITH CORDLESS AND CELL
PHONE, RADIOS, TELEVISIONS AND OTHER ELECTRICAL
PHONE, RADIOS, TELEVISIONS AND OTHER ELECTRICAL
DEVICES. TO CORRECT THE PROBLEM MOVE THE DEVICE
DEVICES. TO CORRECT THE PROBLEM MOVE THE DEVICE
AWAY FROM THE LUMINARY OR PLUG INTO A DIFFERENT
AWAY FROM THE LUMINARY OR PLUG INTO A DIFFERENT
OUTLET. THIS PRODUCT MAY CAUSE INTERFERENCE TO
OUTLET. THIS PRODUCT MAY CAUSE INTERFERENCE TO
RADIO EQUIPMENT AND SHOULD NOT BE INSTALLED NEAR
RADIO EQUIPMENT AND SHOULD NOT BE INSTALLED NEAR
MARITIME SAFETY COMMUNICATIONS EQUIPMENT OR OTHER
MARITIME SAFETY COMMUNICATIONS EQUIPMENT OR OTHER
CRITICAL NAVIGATION OR COMMUNICATION EQUIPMENT
CRITICAL NAVIGATION OR COMMUNICATION EQUIPMENT
OPERATING BETWEEN 0.45-30 MHz.
OPERATING BETWEEN 0.45-30 MHz.
NOTE:
NOTE: