User Manual

INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED VERSION
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
DRAWING NO. A68128 REV -- (FRONT)
©2009 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-71-68128
OPENING & CLOSING THE ACCESS PANEL:OPENING & CLOSING THE ACCESS PANEL:
1. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE1. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE
BASE COVER TO THE UNIT, TOTALLY DISENGAGING THEM BASE COVER TO THE UNIT, TOTALLY DISENGAGING THEM
FROM THE CASTING. (SEE FIGURE 2). THE SCREWS ARE FROM THE CASTING. (SEE FIGURE 2). THE SCREWS ARE
DISENGAGED WHEN THE SCREWS CAN MOVE FREELY DISENGAGED WHEN THE SCREWS CAN MOVE FREELY
UP AND DOWN. UP AND DOWN.
2. LIFT THE BASE COVER FREE.2. LIFT THE BASE COVER FREE.
3. TO REINSTALL THE BASE COVER, REPEAT THE STEPS ABOVE3. TO REINSTALL THE BASE COVER, REPEAT THE STEPS ABOVE
IN REVERSE ORDER. IN REVERSE ORDER.
NOTE: BE SURE THAT THE “SS” EMBOSSMENT ON THE BASENOTE: BE SURE THAT THE “SS” EMBOSSMENT ON THE BASE
COVER IS ORIENTED WITH THE STREET SIDE OF THE UNITCOVER IS ORIENTED WITH THE STREET SIDE OF THE UNIT
AS DEPICTED.AS DEPICTED.
FULL CUTOFF BASE COVER REMOVAL & INSTALLATION:FULL CUTOFF BASE COVER REMOVAL & INSTALLATION:
11.. TO OPEN THE ACCESS PANEL, LOCATE THE FOUR CLOSURETO OPEN THE ACCESS PANEL, LOCATE THE FOUR CLOSURE
SCREWS. THESE ARE LOCATED INSIDE THE RING OF LEDs, SCREWS. THESE ARE LOCATED INSIDE THE RING OF LEDs,
MOUNTED IN A PLATE UNDER THE HOOD (SEE FIGURE 1.) MOUNTED IN A PLATE UNDER THE HOOD (SEE FIGURE 1.)
2. LOOSEN THE FOUR CLOSURE SCREWS. T2. LOOSEN THE FOUR CLOSURE SCREWS. THE SCREWS ARE HE SCREWS ARE
ADEQUATELY LOOSENED WHEN T ADEQUATELY LOOSENED WHEN THE HE ACCESS PANEL ACCESS PANEL CAN CAN
MOVE FREELY UP MOVE FREELY UP AND AND DOWN. DOWN.
3. 3. SLIDE THE ACCESS PANEL OVER TO THE ROUND AREAS SLIDE THE ACCESS PANEL OVER TO THE ROUND AREAS
OF THE KEYHOLE SLOTS, DISENGAGE IT FROM THE OF THE KEYHOLE SLOTS, DISENGAGE IT FROM THE
SCREW HEADS, AND LOWER THE PANEL. IT WILL HANG SCREW HEADS, AND LOWER THE PANEL. IT WILL HANG
SAFELY FROM THE POWER SUPPLY WIRING. SAFELY FROM THE POWER SUPPLY WIRING.
4. TO 4. TO REPLACE REPLACE THE THE PANELPANEL, SIMPLY , SIMPLY PLACE THE KEYHOLEPLACE THE KEYHOLE
SLOTS OVER THE SCREW HEADS, SLIDE THE PANEL SLOTS OVER THE SCREW HEADS, SLIDE THE PANEL
OVER AND RE-TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS. OVER AND RE-TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS.
CAUTION
!
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE SERVICING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
CAUTION
!
STREESTREETT SIDE VIEW SIDE VIEW
FIGURE 1FIGURE 1
MAX POLE OD 3”MAX POLE OD 3”
MIN POLE OD 2.375"MIN POLE OD 2.375"
LOWER HOUSINGLOWER HOUSING
ACCESS ACCESS
PANEL PANEL
SCREWS (4)SCREWS (4)
CUPOLCUPOL
AA CAP CAP
CUPOLCUPOL
AA BASE BASE
CUPOLCUPOL
AA LENS LENS
HOODHOOD
LADDER RESLADDER RESTT (2) (2)
-OPTIONAL--OPTIONAL-
SESETT SCREWS (3) SCREWS (3)
ADJUSADJUS
TT PHO PHOTTOCONTROLOCONTROL
BBYY LIFTING & TURNING LIFTING & TURNING
CUPOL
CUPOL
AA SIMU SIMULTLTANEOUSANEOUSLLYY
BASE COVERBASE COVER
TM
CAPTIVECAPTIVE
SCREW FORSCREW FOR
POWERPOWER
PAD (4)PAD (4)
CHIMNEY CHIMNEY
REST REST
CHIMNEY RESTCHIMNEY REST
ATTACHMENTATTACHMENT
SCREW (2) SCREW (2)
DO NOT DO NOT
REMOVEREMOVE
LENSLENS
PPANEL (4)ANEL (4)
"SS" EMBOSSMENT"SS" EMBOSSMENT
FIGUREFIGURE 22
OPENOPEN
HOOD -HOOD - TTOP VIEWOP VIEW
LOWER LOWER
HOUSINGHOUSING