Owner manual

INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED 2ND GEN
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
DRAWING NO. A72916 REV -- (FRONT)
©2013 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72916
OPENING & CLOSING THE UNIT:
OPENING & CLOSING THE UNIT:
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
ABOVE).
ABOVE).
2. UNSCREW THE TWO SCREWS ATTACHING THE BOTTOM
2. UNSCREW THE TWO SCREWS ATTACHING THE BOTTOM
COVER. (SEE FIGURE 2).
COVER. (SEE FIGURE 2).
3. LOCATE THE WIRING DIAGRAM ATTACHED UNDER THE
3. LOCATE THE WIRING DIAGRAM ATTACHED UNDER THE
BOTTOM COVER. USE AS A GUIDE FOR CONNECT THE POWER
BOTTOM COVER. USE AS A GUIDE FOR CONNECT THE POWER
SUPPLY LEADS TO THE TERMINAL BLOCK.
SUPPLY LEADS TO THE TERMINAL BLOCK.
4. PULL UP THE TERMINAL BLOCK COVER. (SEE FIGURE 2).
4. PULL UP THE TERMINAL BLOCK COVER. (SEE FIGURE 2).
5. UNSCREW THE TERMINAL BLOCK SCREWS AND CONNECT
5. UNSCREW THE TERMINAL BLOCK SCREWS AND CONNECT
PROPER THE SUPPLY LEADS ON EACH POSITION.
PROPER THE SUPPLY LEADS ON EACH POSITION.
6. TIGHTENING THE SCREWS FROM TERMINAL BLOCK.
6. TIGHTENING THE SCREWS FROM TERMINAL BLOCK.
RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.
RECOMMENDED TORQUE FOR SCREWS 35 IN-LBS.
7. PUSH DOWN THE TERMINAL BLOCK COVER.
7. PUSH DOWN THE TERMINAL BLOCK COVER.
8. SECURE THE BOTTOM COVER.
8. SECURE THE BOTTOM COVER.
9. CLOSE THE UNIT.
9. CLOSE THE UNIT.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
WIRING:
WIRING:
1.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO
2. UNSCREW THE TWO
CAPTIVE
CAPTIVE
CLOSURE SCREWS. YOU WILL
CLOSURE SCREWS. YOU WILL
KNOW
KNOW
T
T
HE SCREWS ARE COMPLETELY DISENGAGED FROM
HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD
THE HOOD
WHEN
WHEN
THE SCREWS CAN MOVE FREELY UP AND
THE SCREWS CAN MOVE FREELY UP AND
DOWN.
DOWN.
3. OPEN THE HOOD.
3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
TIGHTEN
TIGHTEN
THE TWO CA
THE TWO CAP
TIVE CLOSURE SCREWS.
TIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL
SIMPLY PULL
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
INDEX FINGER WHILE
INDEX FINGER WHILE
PUSHING UP ON THE HOOD WITH YOUR
PUSHING UP ON THE HOOD WITH YOUR
THUMBS. CLOSE THE UNIT BY
THUMBS. CLOSE THE UNIT BY
CLOSING THE HOOD AND PRESSING
CLOSING THE HOOD AND PRESSING
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
CAUTION
!
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
CUPOLA CAP
CUPOLA CAP
CUPOLA BASE
CUPOLA BASE
CLOSURE
CLOSURE
SCREW
SCREW
BOSS (2)
BOSS (2)
SCREW NOT
SCREW NOT
SHOWN
SHOWN
LOWER HOUSING
LOWER HOUSING
MIN POLE OD 2.375”
MIN POLE OD 2.375”
MAX POLE OD 3”
MAX POLE OD 3”
SET SCREWS (3)
SET SCREWS (3)
LADDER REST (2)
LADDER REST (2)
-OPTIONAL-
-OPTIONAL-
LENS
LENS
PANELS (4)
PANELS (4)
TRIGGER
TRIGGER
LATCH (2)
LATCH (2)
-OPTIONAL-
-OPTIONAL-
CUPOLA LENS
CUPOLA LENS
ADJUST PHOTOCONTROL
ADJUST PHOTOCONTROL
BY LIFTING & TURNING
BY LIFTING & TURNING
CUPOLA SIMULTANEOUSLY
CUPOLA SIMULTANEOUSLY
FIGURE 1
FIGURE 1
CLOSED HOOD - STREET SIDE VIEW
CLOSED HOOD - STREET SIDE VIEW
HOOD
HOOD
FIGURE 2
FIGURE 2
BOTTOM COVER AND
BOTTOM COVER AND
TERMINAL BLOCK ASSEMBLY
TERMINAL BLOCK ASSEMBLY
TM
WARNING
FIXTURE MUST BE GROUNDED
TO FUNCTION AS INTENDED
!
TERMINAL BLOCK
TERMINAL BLOCK
COVER
COVER
BOTTOM
BOTTOM
COVER
COVER