Instruction Guide

ManualsBrandsAmerican Lighting ManualsOtherAmerican Lighting Hybrid 2 216" Long LED 120V Tape Light Kit

SAFETY INFORMATION

• Read all installation instructions before beginning; if not qualiﬁed, do not attempt installation. Contact a qualiﬁed electrician.

• To reduce the risk of ﬁre, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this

product. Save these instructions for future use.

• Do not cover this product as the covering may cause rope to overheat, melt, or ignite.

• Do not operate Hybrid 2 while it is tightly coiled.

• Do not submerge ﬂexible light in liquids, or use the product in the vicinity of standing water or other liquids.

• Do not route the cord or Hybrid 2 through walls, ceilings, doors, windows, or any similar part of the building structure.

• Secure this ﬂexible light using only the mounting clips provided or factory recommended mounting track (sold separately).

• Do not secure this product or its cord with staples, nails, or like means that may damage the insulation.

• Do not use if there is any damage to the PVC housing or power cord insulation. Inspect periodically.

• Do not install on gates or doors, where subject to continuous ﬂexing.

• Do not install in tanks or enclosures of any kinds.

• Follow instructions carefully when splicing Hybrid 2 sections or attaching power cords. Ensure that all connections,

including the end cap on the last segment, are properly installed with dielectric grease and shrink tube to preclude the

entrance of water (outdoor applications).

• Risk of ﬁre. Do not replace attachment plug. Discard product if attachment plug is damaged.

• This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will ﬁt in a

polarized outlet only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician.

Never use with an extension cord unless plug can be fully inserted. Do not alter plug. This plug contains an electrical fuse as a safety feature.

See Page 2 for instructions on replacing the fuse (Use only 8 Amp 125 Volt fuse).

• 120V Hybrid 2 is cETLus Listed, but this safety rating is void if the 150ft reel is cut. Cutting the Hybrid 2 Kit and/or altering the power cord in

any way including, but not limited to cutting, splicing, and/or adding any power accessories will void the cETLus Listing.

• This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.

• Do not exceed 150ft maximum run distance in any single run.

PRODUCT INFORMATION

Hybrid 2 Kits are sold in 3ft, 6ft, 12ft, 18ft, 30ft, and 45ft lengths. Each kit includes (1) 5ft removable power cord, (1) removable end cap, and (1)

mounting clip per foot of length. Mounting accessories include H2-CLIPS (bag of ten plastic mounting clips), H2-TRACK-3 (3ft plastic track) and/or

H2-CHAN-3 (3ft aluminum mounting channel); all sold separately. Jumpers (linking extensions) include 6”, 3ft, and 6ft lengths for kits.

Power consumption = 3 W/ft; Maximum run = 150 feet

These products may represent a possible shock or ﬁre hazard if

improperly installed or attached in any way. Products should be

installed in accordance with these instructions, current electrical

codes, and/or the current National Electric Code (NEC).

To reduce the risk of ﬁre, electric shock or injury to persons,

use this ﬂexible light only with American Lighting recommended

drivers, controllers, power connectors, jumpers and extensions.

120V Hybrid 2 Kits are cETLus Listed and interconnectable up

to 150ft. Safety rating is void if a kit is cut or altered, or if used

with any power cord other than the one provided.

To reduce the risk of ﬁre, electric shock or injury to persons,

make sure that the electrical power to the ﬁxture is

disconnected at the source prior to installation or any servicing.

When using outdoor portable lighting products, basic safety precautions should always be followed to reduce the risk of

ﬁre, electric shock, and personal injury, including the following:

• Use dielectric grease and shrink tube at all power connections, including end cap when using outdoors.

• Use ground fault circuit interrupter (GFCI) protection on the circuit(s) or outlet(s) when using outdoors.

• Use only UL approved outdoor extension cords, such as type SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW. This designation is

marked on the jacket of the extension cord.

WARNING

HYBRID 2 Kits120V

INSTALLATION INSTRUCTIONS

H2-KIT Series

Do not operate Hybrid 2 while it is coiled.

Summary of content (2 pages)

PAGE 1
20V HYBRID 2 Kits INSTALLATION INSTRUCTIONS H2-KIT Series WARNING WARNING These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC). WARNING 120V Hybrid 2 Kits are cETLus Listed and interconnectable up to 150ft.
PAGE 2
120V HYBRID 2 Kits INSTALLATION INSTRUCTIONS H2-KIT Series EXTENDING HYBRID 2 KITS (See Figure 1): Note: When connecting multiple Hybrid 2 Kits together, do not exceed the maximum run length as noted by the tag on the cord: 150ft max FIGURE 1 1. Turn the plastic end cap counter-clockwise to remove from the first kit. 2. Remove power cord from the second kit. 3. Connect the kits by plugging the male and female halves into each other, then tightenint the screw-on connection cover. 4.